Viconics R820 REV2 Series Manuel utilisateur

Product overview

R820 REV2 SERIES

SCR POWER CONTROLS

NOVEMBER 2017

The Viconics R820 series SCR power controls are designed for cost effective, precise

modulation of electric loads for most electric heating applications.

(Applicable on resistive loads only)

The R820 series consists of SCR’s power controls, c/w factory assembled heatsink for

surface or in-panel mounting.

Models available

Model No.

Voltage Range

Phase

Max Current

R820-211-REV2

24 - 240 Volts AC

Amp

R820-213-REV2

24 - 240 Volts AC

Amp

R820-321-REV2

24 - 347 Volts AC

Amp

R820-323-REV2

24 - 347 Volts AC

Amp

R820-341-REV2

24 - 347 Volts AC

Amp

R820-343-REV2

24 - 347 Volts AC

Amp

R820-421-REV2

24 - 480 Volts AC

Amp

R820-423-REV2

24 - 480 Volts AC

Amp

R820-441-REV2

24 - 480 Volts AC

Amp

R820-443-REV2

24 - 480 Volts AC

Amp

R820-471-REV2

24 - 480 Volts AC

Amp

R820-621-REV2

24 - 600 Volts AC

Amp

R820-623-REV2

24 - 600 Volts AC

Amp

R820-641-REV2

24 - 600 Volts AC

Amp

R820-643-REV2

24 - 600 Volts AC

Amp

R820-671-REV2

24 - 600 Volts AC

Amp

R820-PCB-A01

24 Vac Electronic PCB

1 or 3

-----

Features

Feature

Benefit

Complete assembly with factory installed heat sink.

Reduced total installation cost

Designed for surface or panel mounting

Covers wider array of application with same

component.

UL Recognized

Easily integrated into complete assemblyrequiring

industry listings.

CSA approved for Canada and USA

Trouble free approval process

Status LED

Quick field troubleshooting.

High quality assembly with 2-year warranty

Reduced field service calls.

Full line of matching peripheral temperature

controllers

Simplified component sourcing and matching for

reliable operation

They are compatible with many industry standard signals. A typical application would be to control a modulating

electric duct heater with a 0 to 10 Vdc control signal from an analog room thermostat. The R820 power controller also

contain four dip switch to adjust to the following control signals:

•0 to 10 Vdc control signal ( 2 to 10 Vdc control range)

•4 to 20 mA control signal

Power modules installation

Important.

All external safety devices like: contactors, relays, flow switch & thermal protections are to be supplied and

installed by other.

When the SCR is installed inside a panel, the enclosure needs to be adequately louvered for proper ventilation

and heat dissipation. Call the factory for the derating amperage curves for these specific applications.

Electronic controls require special care for wiring and startup. To avoid problems, carefully follow the

procedures below.

Look at the wiring diagrams, and study them carefully. Be sure that you understand how the system is supposed to

work.

A) Location:

1- Can be installed inside a louvered approved cabinet or with the heatsink mounted externally.

2- Must be installed away from excessive heat source.

3- Nothing must restrain air circulation to the heatsink.

B) Installation:

1- If installed completely inside a cabinet, use the mounting tabs on the heatsink to secure the SCR to the back

plate of the panel.

2- If installed with heatsink outside the cabinet, use the proper model mounting template for the cut-out

dimensions and to check for mounting obstructions.

3- Respect mounting orientation

(this side up).

4- Mount the heatsink verticallyon the side of the cabinet for proper heat dissipation.

5- Do not relocate the power switching modules on the heatsink.

R820 Installation and Dimensions

•Mounting instructions & templates are available from the factory.

•The cutout templates include hole positions for heatsink attachment to the electrical cabinet

❖Single phase R820 will have 2 mounting screw, 1 on each side.

❖Three phase R820 will have 4 mounting screw, 2 on each side.

•Respect mounting orientation (this side up).

•Mount the heatsink vertically on the side of the cabinet for proper heat dissipation.

•If mounted on top or bottom of the cabinet, derate maximum usable amperage by 25%.

•Do not relocate the power switching modules on the heatsink.

R820 single phase

Weight

R820-211-REV2

5.25 "

4.50 "

2.56”

3.00 "

3.75 "

1.80

R820-321-REV2

5.25 "

4.50 "

2.56”

3.00 "

3.75 "

1.80

R820-341-REV2

5.25 "

6.50 "

2.56”

3.00 "

3.75 "

2.40

R820-421-REV2

5.25 "

4.50 "

2.56”

3.00 "

3.75 "

1.80

R820-441-REV2

5.25 "

6.50 "

2.56”

3.00 "

3.75 "

2.40

R820-471-REV2

5.25 "

10.00 "

2.56”

3.00 "

3.75 "

3.50

R820-621-REV2

5.25 "

4.50 "

2.56”

3.00 "

3.75 "

1.80

R820-641-REV2

5.25 "

6.50 "

2.56”

3.00 "

3.75 "

2.40

R820-671-REV2

5.25 "

10.00 "

2.56”

3.00 "

3.75 "

3.50

R820 three phase

Weight

R820-213-REV2

5.25 "

6.50 "

2.56”

3.00 "

5.75 "

2.60

R820-323-REV2

5.25 "

6.50 "

2.56”

3.00 "

5.75 "

3.70

R820-343-REV2

5.25 "

10.00 "

2.56”

3.00 "

5.75 "

3.70

R820-423-REV2

5.25 "

6.50 "

2.56”

3.00 "

5.75 "

2.65

R820-443-REV2

5.25 "

10.00 "

2.56”

3.00 "

5.75 "

3.70

R820-623-REV2

5.25 "

6.50 "

2.56”

3.00 "

5.75 "

2.65

R820-643-REV2

5.25 "

10.00 "

2.56”

3.00 "

5.75 "

3.70

DIP Switch Adjustments per applications

INPUT SIGNAL

SWITCH #1

SWITCH #2

SWITCH #3

SWITCH #4

0 to 10 Vdc control signal (2 to 10 Vdc control range)

Off

4 to 20 mA control signal

Off

Typical applications

0 To 10 Vdc From a Thermostat

Dip switch position

2 Vdc = 0% capacity

10 Vdc = 100% capacity

0 to 10 Vdc control signal

Off

24vac

Common

24Vac

0 to 10Vdc output

(Thermostat)

(Second SSR

only on 3 phases

models)

The 45 & 75 Amps models need to be wired with the supplied high voltage lugs. These lugs are shipped

reversed. Unscrew these lugs first.

*** Attach the wire to the lug first, and then screw the lug to the power module.

Shipping state Proper

installation

Separate for

wiring

Illustration 1

0 To 10 Vdc From a Building Automation System

Dip switch position

2 Vdc = 0% capacity

10 Vdc = 100% capacity

0 to 10 Vdc control signal

Off

24vac

(Second SSR

only on 3 phases

models)

4 TO 20mA From a Building Automation System

Dip switch position

4 mA = 0% capacity

20 mA = 100% capacity

4 to 20 mA control signal

Off

24vac

(Second SSR

only on 3 phases

models)

24 Vac Power& Wiring

•It is not necessary to ground any leg of the transformer to earth with the controller card.

•The controller uses internally a half wave rectifier bridge. On 0 to 10 Vdc control signal, the reference of the control

signal is the Common of the power supply of the SCR controller card.

•Use a Class 1 (properlyfused) or Class 2, CSA or UL recognized transformer.

High voltage Wiring

General cautions:

•High voltages are present on the terminals of these devices. Please read all the instruction in this manual carefully.

•The 45 & 75 Amps models need to be wired with the supplied high voltage lugs. Detach the lug from the SSR

first, connect the wires, and then screw the lug to the power module. Refer to Illustration 1 on page 3.

•Have the wiring done by a qualified and skilled professional.

•High voltage and amperage can be fatal.

•All wiring must conform to national electrical code regulations.

•The instrument must be wired before applying power.

•Protect circuits with semi-conductor fuses.

•For in panel installation, derating amperage curves are available from the factory.

Specifications

Operating Conditions: 0°C to 80°C (32°F to 176°F) / 0 % to 95 % R.H.

non-condensing

Thermostatic protection: Self-resetting. Auto shut off when SCR ambient temp. is above 82°C (180°F)

Power supply: 24 Vac -15%, +10% 50/60 Hz; 2 VA

Use a Class 1 (properlyfused) or Class 2, CSA or UL recognized transformer.

Troubleshooting

•Check general wiring, as per heater manufacturer diagram.

•Be sure you understand the system and its normal operation

•Verify high voltage power supply wiring

•Verify that correct voltage is present at the heater with proper wire size

•Verify low voltage 24 Vac power supply wiring: 24 Vac is present at terminals 1 & 2 of the

R820 SCR

•Create or simulate 100 % heating demand Using present control system

R820 Configured for 0 to 10 Vdc input signal

•Signal between terminals 1 & 3 is 10 Vdc or superior

•Dip switch properly configured: S1=Off, S2=Off, S3=Off & S4=On

•Be sure that the polarity is correct and not reversed + to +, - to –

•LED on SCR is on 100 % of the time

R820 Configured for 4 to 20 mA input signal

•Signal between terminals 1 & 3 is 20 mA or superior

•Dip switch properly configured: S1=Off, S2=Off, S3=On & S4=Off

•Be sure that the polarity is correct and not reversed + to +, - to –

•LED on SCR is on 100 % of the time

•Verify amperage consumption of the heater: LED on SCR is on 100 % of the time

•Verify & correct 24 Vac power supply to the SCR

•Verify low voltage fuses, protections, flow switch,

•Verify control wiring & control signal

•Correct control signal is present at the SCR Check polarity of control signal

•Verify fuses & all protections & contact the heater manufacturer

Viconics Technologies Inc.

Tel.: Fax: Toll free:

www.viconics.com

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Viconics Contrôleurs

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics VT7225 series Manuel utilisateur

Viconics

Viconics VT7600 Series Manuel utilisateur

Viconics

Viconics ZigBee Pro VT8000 Series Manuel utilisateur

Viconics

Viconics VTR8300 Series Manuel utilisateur

Viconics

Viconics VZ8250 Manuel utilisateur

Viconics

Viconics VC3000 Series Manuel utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Viconics

Viconics VTR8300 Series Manuel utilisateur

Viconics

Viconics VT7200 F 5000 B Manuel utilisateur

Viconics

Viconics R851V-4 Manuel utilisateur

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics VZ7656F1000B Manuel utilisateur

Viconics

Viconics R820 REV2 Series Manuel utilisateur

Viconics

Viconics VT8000 Series Fiche technique

Viconics

Viconics VT76 Series Manuel d'utilisation et d'entretien

Viconics

Viconics VTR7300 Series Manuel utilisateur

Viconics

Viconics VT7600E Series Manuel utilisateur

Viconics

Viconics R851B Manuel utilisateur

Viconics

Viconics VTR8300 Series Guide de l'utilisateur

Viconics

Viconics VT7200 Series Manuel utilisateur

Viconics

Viconics VZ7260 5 00B Series Guide de l'utilisateur

Viconics

Viconics VT8000 Series Manuel utilisateur

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur