VIA Technologies VT8237R Manuel utilisateur

Electronic Emission Notices

Federal Communications Commission (FCC) Statement

This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordance with instructions contained in this manual, may cause harmful interference

to radio and television communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which

can be determined by turning the equipment off and on, the user is encouraged to try to

correct the interference by one or more of the following measures:

- REORIENT OR RELOCATE THE RECEIVINGANTENNA

- INCREASE THE SEPARATION BETWEEN THE EQUIPMENT AND THE RECEIVER

- CONNECT THE EQUIPMENT INTO AN OUTLET ON A CIRCUIT DIFFERENT FROM

THAT OF THE RECEIVER

- CONSULT THE DEALER OR AN EXPERIENCEDAUDIO/TELEVISION TECHNICIAN

NOTE: Connecting this device to peripheral devices that do not comply with Class B

requirements, or using an unshielded peripheral data cable, could also result in

harmful interference to radio or television reception.

The user is cautioned that any changes or modifications not expressly approved

by the party responsible for compliance could void the user’s authority to operate

this equipment.

To ensure that the use of this product does not contribute to interference, it is

necessary to use shielded I/O cables.

copied or reproduced by any means.

While every precaution has been taken in the preparation of this manual, no responsibility

for errors or omissions is assumed. Neither is any liability assumed for damages resulting

from the use of the information contained herein.

Trademarks

All brand names, logos and registered trademarks mentioned are property of their

respective owners.

Technical Reference Booklet

Table of Contents

HARDWARE CONFIGURATION ....................................................... 4

Key Features ............................................................................................... 4

MOTHERBOARD LAYOUT ................................................................ 7

REAR PANEL .................................................................................... 8

AUDIO CONFIGURATION ................................................................ 10

SPEAKER CONFIGURATION ............................................................ 10

Method 1: 4/6 Surround audio output of back panel only ........................... 10

Method 2: Using S-Bracket connectors ...................................................... 12

JACK-SENSING INSTRUCTION ........................................................ 14

JUMPER SETTING ............................................................................... 1 6

JBAT1 - CMOS Clear ................................................................................... 16

JP1-Keyboard Power Select Jumper .......................................................... 16

CONNECTORS ................................................................................. 17

Floppy Disk Drive Connector:CN3 .............................................................. 17

Hard Disk Connectors:CN1&CN2 .............................................................. 17

Serial ATA Hard Disk Connectors:SATA-1&SATA-2 ..................................... 18

USB Connectors :USB1/USB2/USB3 ......................................................... 20

Fan Power Connectors:CPU FAN/SYS FAN/WOL ....................................... 21

CD-IN Connector:CDS1 .............................................................................. 22

Front Panel Audio Header:FPS1 ................................................................. 23

S-Bracket (SPDIF)/LEN/LFE/Surround Output Connector:

CN6(optional) ................................................................................................. ..... 24

Front Panel Header:FP1 ............................................................................. 26

SLOTS .............................................................................................. 27

CPU INSTALLATION ........................................................................ 28

HARDWARE SETUP ......................................................................... 32

To Install DDR DIMMs ................................................................................. 32

BIOS SETUP ..................................................................................... 33

Starting Setup .............................................................................................. 33

Main Menu ................................................................................................... 34

Standard CMOS Features ........................................................................... 35

Advanced BIOS Features ............................................................................ 36

Advanced Chipset Features ........................................................................ 36

Integrated Peripherals ................................................................................ 36

Power Management Setup .......................................................................... 36

PNP/PCI Configurations ............................................................................. 36

PC Health Status ......................................................................................... 36

Frequency/Voltage Control .......................................................................... 37

Set Supervisor/User Password .................................................................. 37

Flash Update Procedure ............................................................................. 38

VT8237R/VT8237 SATA RAID USER MANUAL ............................. 39

Enter BIOS Configuration Utility .................................................................. 39

Create Disk Array ......................................................................................... 40

Delete Disk Array ......................................................................................... 42

Select Boot Array ......................................................................................... 42

Duplicate Critical RAID 1 Array .................................................................... 43

Rebuild Broken RAID 1 Array ...................................................................... 44

DRIVER AND RAID SOFTWARE INSTALLATION ............................ 46

Microsoft Windows Driver Installation ......................................................... 46

INSTALL OPERATING SYSTEM INTO SATA HDD

OF VT8237R/VT8237 ..................................................................... 48

Install Windows 98SE or Me ....................................................................... 48

Install Windows NT4.0,2000,XP ................................................................. 48

APPENDIX ....................................................................................... 48

Technical Reference Booklet

HARDWARE CONFIGURATION

Key Features :

Chipset

• VIA P4M800+VT8237R/VT8237 chipset.

Processor

• Supports Intel® Celeron® , Pentium® 4 processors in the LGA775

package (with 0.8V~1.6V voltage).

• Supports PSB (Processor System Bus) frequency of 533MHz

(133MHz bus clock).

• Supports PSB (Processor System Bus) frequency of 800MHz

(200MHz bus clock).

• Supports Hyper-Threading Technology.

VRM 10.0 (Voltage Regulator Modules) on Board

• Flexible motherboard design with on board VRM 10.0, easy to upgrade

with future Intel® Celeron, Pentium®4 processors.

• 0.8375V to 1.600V in 12.5mV steps.

System Memory

•A total of two 184-pin DDR SDRAM sockets.

• Support up to 2GB DRAMs for unbuffered DDR SDRAM module.

• Support

DDR400/333/266 DDR SDRAM.

• 2.5V DRAM interface for DDR SDRAM.

System BIOS

• PnP, APM, ATAPI and Windows® 98/2000/XP.

• Full support of ACPI & DMI.

• Auto detects and supports LBA harddisks with capacities over 160 GB.

• Easy to upgrade BIOS by end-user.

On-board I/O

•On board two PCI fast IDE ports supporting up to 4 ATA, ATA2 , Ultra

ATA33/ 66/100/133 IDE HDDs, CD-ROMs, ZIP drives and LS-120

drives as boot drive.

•One ECP/EPP parallel port.

•One 16550 Compatible UART serial ports.

•One floppy port supports two FDD of 360KB, 720KB, 1.2MB , 1.44MB

and 2.88MB capacity.

•Eight USB2.0 ports.

•PS/2 keyboard connector.

•PS/2 mouse is supported.

•One Front Panel Sound Connector.

•Infrared (IrDA) is supported via a header.

•One 15-Pins VGA connector.

Serial ATA/RAID Controller (optional)

• Complies with Serial ATA Specificaion Revision 1.0.

•Two ports supported two S-ATA devices.

• Support RAID Configuration.

•S-ATA drive transfer rate is capable of up to 150MB/S per channel.

Expanded USB Support

• Includes 4 UHCI host controllers,increasing the number of external

ports to eight.

• Includes 1 EHCI USB2.0 Host Controller that supports eight ports

(Bandwidth shared between eight ports).

Plug-and-Play

• Supports Plug and Play specification 1.1.

• Plug and Play for Windows® 98, Windows® 2000 as well as

Windows® XP.

• Fully steerable PCI interrupts.

On-board AC97 Sound

•Integrated AC97 controller with standard AC97 Codec.

• Direct Sound and Sound Blaster compatible.

•Full-Duplex 16-bit record and play back.

•PnP and APM 1.2 support.

•Windows® 98/2000/XP drivers ready.

•Line-in, Line-out, Mic-in and MIDI/Game port.

• Supports ALC650/ALC655 AC97 Code for six sound channel output

(optional).

On-board VT6103 LAN (optional)

•High performance PCI master interface with scatter / gather and

bursting capability.

•Standard MII interface to external PHYceiver.

•10/100MHz full and half duplex operation.

Technical Reference Booklet

Integrated UnichromeTM GFX/Video Accelerator

• Optimized Shared Memory Architecture (SMA).

• 16/32/64MB frame buffer using system memory.

• 128-bit 2D/3D graphics engine.

• Full internal AGP 8X performance.

• Microsoft DirectX texture compression.

• High quality DVD video playback.

• CRT resolutions up to 1600X1200.

• 32-bit true color rendering.

• MPEG-2 video textures.

Power Management

• Supports SMM, APM and ACPI.

• Break switch for instant suspend/resume on system operations.

• Energy star “Green PC” compliant.

• Hardware monitoring circuit is supported, provide voltage, temperature,

fan speed, etc. monitoring (optional).

• WOL (Wake-On-Lan) header support (optional).

• Supports suspend-to-RAM(STR)(optional).

Expansion Slots

• 1 AGP slot (support AGP 4X/8X mode).

•2 PCI bus master slots - ver. 2.1 compliant.

Static electricity can harm delicate components of the motherboard.

To prevent damage caused by static electricity, discharge the static

electricity from your body before you touch any of the computers

electronic components.

Motherboard Layout

The following diagrams show the relative positions of the jumpers, connectors, major

components and memory banks on the motherboard.

# The LAN Connector is optional.

# The ALC650/ALC655 embeds an internal analog switch (by driver software)

to share LINE input with Surround output, and share MIC input with CENTER/

LFE output.

NOTE

1) Be sure to check the cable orientation in order to match the colored strip to the pin

1 end of the connector.

2) Be sure to connect PW1 and PWR1 to power supply correctly, otherwise, the mother

-board can’t work normally.

3) When you start up the system, please wait for 5 seconds after you power on AC.

4) It is not recommended to add a metal spacer plate on the back of the Socket775.

Otherwise, some components will be short and damaged.

FOXCONN

REM OVE

LGA775 Socket

Technical Reference Booklet

Rear Panel

The back panel provides the following connectors:

Mouse Connector

The mainboard provides a standard PS/2® mouse mini DIN connector for

attaching a PS/2® mouse.You can plug a PS/2® mouse directly into this

connector.

Keyboard Connector

The mainboard provides a standard PS/2® keyboard mini DIN connector

for attaching a PS/2® keyboard.You can plug a PS/2® keyboard directly into

this connector.

USB 2.0 Connector

The mainboard provides a UHCI (Universal Host Controller Interface)

Universal Serial Bus root for attaching USB devices such as keyboard, mouse

or other USB-compatible devices.You can plug the USB device directly into

the connector.

PIN SIGNAL DESCRIPTION

1 VCC +5V/5VSB (optional)

2 -Data 0 Negative Data Channel 0

3 +Data0 Positive Data Channel 0

4 GND Ground

5 VCC +5V/5VSB (optional)

6 -Data 1 Negative Data Channel 1

7 +Data 1 Positive Data Channel 1

8 GND Ground

USB 2.0 Connector DescriptionUSB 2.0 Connector

Serial Port Connector: COM

The Port is 16550A high speed communication ports that send/receive

16bytes FIFOs. You can attach a serial mouse or other serial devices directly

to the connectors.

LAN Jack (Optional)

The mainboard provides one standard RJ-45 jack for connection to Local

Area Network(LAN).You can connect a network cable to the LAN jack.

Parallel Port Connector:LPT

The mainboard provides a 25-pin female centronic connector as LPT. A

parallel port is a standard printer port that supports Enhanced Parallel Port

(EPP) and Extended Capabilities Parallel Port (ECP) mode.

MIDI/Game Connector

The mainboard provides the game port to connect a joystick or a MIDI

device.

Audio Port Connector

Line_Out is a connector for Speakers or Headphones. Line In is used for

external CD player, Tape player, or other audio devices. Mic In is a connector

for microphones. The ALC650/655 embeds an internal analog switch (by driver

software) to share LINE input with Surround output, and share MIC input with

CENTER/LFE output.

The ALC655 embeds the jack sensing function.When you plug an audio

device into the corresponding connector, the system will show you what you

pluged into the motherboard.

Technical Reference Booklet

Audio Configuration

ALC650/655 support 6 channel output,after installing the audio driver,

you can select 4/6 channel surround audio output in software utility and then

connect surround speakers to appropriate audio ports.

There are two ways to obtain 4/6 channel surround audio output:

1. 4/6 surround audio output of back panel only. All surround speaker

connect to audio connector.

2. S-Bracket (optional cable). You have installed S-Bracket into the

computer, and then connect two front speakers to back panel’s

“Line-out” port, and the rest of speakers to S-Bracket. Detail connection

is refer to Page 25.

Speaker Configuration

Method 1: 4/6 Surround audio output of back panel only.

After installing the audio drivers, you can attach the speakers for 2-/4-/6-

channel audio output. Always connect the speakers to the LINE OUT

connectors. Different connector configurations for 2-/4-/6-channel

operations are listed below:

2-Channel 4-Channel 6-Channel

In 2-channel configuration,

Line Out, Line In and MIC

functions all exist.

When set to 4-channel

configuration, Line In

is replaced by Rear

Speaker Out. Line in

function does not exist.

When set to 6-channel

configuration, Line In

is replaced by Rear

Speaker Out. Mic is

replaced by Center/

Subwoofer Speaker Out.

Line in and Mic do not

exist function.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels VIA Technologies Carte mère

VIA Technologies

VIA Technologies EPIA-CN13000G - VIA Motherboard - Mini ITX Manuel utilisateur

VIA Technologies

VIA Technologies MVP3 Manuel utilisateur

VIA Technologies

VIA Technologies NAB-7500 Manuel utilisateur

VIA Technologies

VIA Technologies 10GWG21Q00020 Manuel utilisateur

VIA Technologies

VIA Technologies VIA P4PB 266E Manuel utilisateur

VIA Technologies

VIA Technologies NAB-7400 Manuel utilisateur

VIA Technologies

VIA Technologies VB9001 Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-P910 Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-SP8000E - VIA Motherboard - Mini ITX Manuel utilisateur

VIA Technologies

VIA Technologies VX800 Series Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-M850 Manuel utilisateur

VIA Technologies

VIA Technologies VAB-950 Guide de sécurité

VIA Technologies

VIA Technologies VB6002 Series Manuel utilisateur

VIA Technologies

VIA Technologies P4MA PRO Manuel utilisateur

VIA Technologies

VIA Technologies VT82C694X Pro Manuel utilisateur

VIA Technologies

VIA Technologies PT-DVBX Manuel utilisateur

VIA Technologies

VIA Technologies KT400A Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-M830 Manuel utilisateur

VIA Technologies

VIA Technologies EPIA Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-P830 Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-M860-12E Manuel utilisateur

VIA Technologies

VIA Technologies EPIA-P720 Manuel utilisateur

VIA Technologies

VIA Technologies EPIA ME6000 - VIA Motherboard - Mini ITX Manuel utilisateur

VIA Technologies

VIA Technologies VAB-600-A Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur