Venstar P474-1100RF Manuel utilisateur
OWNER'S MANUAL
P474-1100RF
2 Stage
Heat & Cool
or
Heat Pump
Programmable
Digital Thermostat
Wireless
Wireless Operation
7-Day Programmable
4 Time Periods Per Day
Programmable Fan
Large, Easy to Read Display
Thermoglow Backlight
Auto-Changeover
Dual Setpoint
2 Heat and 2 Cool Stages
MODE
FAN
TOTALINE
Replacement Components Division Carrier Corporation 03/07
Wireless
TOTALINE
Table Of Contents
Page 1
P/N P474-1100RF
Replacement Components Division Carrier Corporation 03/07
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) this device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.
C
c
FP474-1100RF
FCC ID MUH-T10013
CAUTION Follow Installation Instructions carefully.
DISCONNECT POWER TO THE HEATER -
AIR CONDITIONER BEFORE REMOVING
THE OLD THERMOSTAT AND INSTALLING
THE NEW THERMOSTAT.
WARNING
FRONT PANEL
DISPLAY
QUICK START Set the clock and go
SELECTING THE HEAT
OR COOL MODE
BASIC OPERATION
PROGRAMMING A DAILY
SCHEDULE
ADVANCED SETUP
ABOUT ADVANCED FEATURES
& OPERATION
WARRANTY
2
3
5
6
7
12
16
19
8
FAN
MODE
TOTALINE
Front Panel
Page 2
Liquid Crystal Display
with Thermoglow
Up/Down Buttons
Mode Button
Fan Button
Transmission Indicator
Blinking Green = Communicating
with the Receiver
Display
Page 3
88
88
HEAT
COOL
OFF
AUTO
Fan On
Program
Locked
Setup
On
o
o
Am
Pm
I8 88
88
:
Day
Night
Evening
Morning
SuMoTuWeThFrSa
Mode Indicators - Page 6
Selects the operational mode of the equipment.
HEAT - Indicates the heating mode.
COOL - Indicates the air conditioning mode.
AUTO - Indicates the system will automatically
changeover between heat and cool modes
as the temperature varies.
PROGRAM ON - Indicates the time period
program is enabled to run.
OFF - Indicates heating and cooling are turned off.
Clock with Day of the Week - Page 5
Indicates the current time and day. This clock is
also used to program the time period schedules.
Room Temperature Display
Indicates current room temperature.
Desired Set Temperature - Page 7
Indicates desired room temperature(s).
Display
Page 4
Morning, Day, Evening &Night icons - Pages 8-10
Indicates the day part of the time period program.
Setup icon - Pages 12-14
Indicates the thermostat is in the setup mode.
Fan On icon - Page 7
Indicates constant, continuous fan operation.
When Fan On is not lit - indicates the fan will only
operate when necessary to heat or to cool.
Locked icon - Page 18
Indicates the keypad has been locked.
88
88
HEAT
COOL
OFF
AUTO
Fan On
Program
Locked
Setup
On
o
o
Am
Pm
I8 88
88
:
Day
Night
Evening
Morning
SuMoTuWeThFrSa
MODE
FA N
Quick Start Set the Clock and Go
Page 5
2
Setup
Su
Press
MODE
Setup
Am
I2 00 i
:
Press the MODE button.
While holding MODE,
press the FAN button for
two seconds to enter Setup
screens.
MODE
FA N
buttons.
To adjust the
Clock or Day use
During Setup & Programming:
Pressing the UP or DOWN
button will modify the
flashing selection.
The thermostat is preprogrammed from the factory to operate
one or two stage equipment* without the need for further
programming. To optimize the installation of this thermostat,
follow the instructions in the Advanced Setup section.
* The thermostat is not preprogrammed from the factory to operate
electric heat or heat pump systems. To control these systems,
follow the instructions in the Receiver manual.
Setting the ClockSetting the Clock
Setting the DaySetting the Day
Tip: To change hours
quickly, press and
hold the FAN button,
then press the UP or
DOWN button.
Press the MODE button.
While holding MODE,
press the FAN button for
two seconds to enter Setup
screens.
Page 6
68
HEAT
oo
Pm
70
Mo
I2 00
:
76
COOL
oo
Pm
70
Mo
68
76
HEAT
COOL
AUTO
oo
oo
Pm
70
Mo
OFF
Pm
70
Mo
68
76
HEAT
COOL
ProgramOn
oo
oo
Pm
70
Day
Mo
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Select Mode by Pressing the MODE Button
The HEAT setting indicates the
temperature the room has to
reach before the furnace will
turn on to heat the room.
Heating Only
The COOL setting indicates the
temperature the room has to
reach before the air conditioner
will turn on to cool the room.
Cooling Only
OFF indicates both heating
and air conditioning
systems are turned off.
Off
AUTO will automatically select
heat or cool based on room
temperature demand.
Heating or Cooling
Time Schedule for
Heating or Cooling
The Program On setting will
activate the time period
programming for the cooling
or heating setpoint ONLY
(Morning, Day, Evening
& Night Periods).
Selecting the Heat or Cool Mode
I2 00
:
I2 00
:
I2 00
:
I2 00
:
Page 7
Basic Operation
68
76
HEAT
COOL
AUTO
o
o
Pm
12:00
70
Mo
:
buttons.
Adjust the desired
set temperature with the
Press
FA N
55
85
HEAT
COOL
o
o
Pm
12:00
65
Mo
:
Fan On
Using the Fan Button
Fan On indicates constant fan
operation. You may turn the fan
on even if the thermostat is in the
Off mode. Pressing the FAN button
toggles this feature on or off.
HEAT OR COOL MODE
Pressing the UP or DOWN button in Heat or Cool mode will
adjust only the heat or cool set temperature.
76
COOL
o
Pm
12:00
70
Mo
:
buttons.
Adjust the desired
set temperature with the
Selecting Your Desired Temperature
(adjusting the setpoints)
AUTO OR PROGRAM MODE
Pressing the UP or DOWN button in Auto or Program mode will
adjust both the heat and cool set temperatures simultaneously.
(Unit # 1 only)
Page 8
Press
MODE
Press
MODE
Press
MODE
Press
MODE
MODE
Continued
Mo
Start
Am
6 00
Morning
Mo
:
78
COOL
o
Am
6 00
Morning
Mo
:
70
78
HEAT
COOL
o
o
Am
6 00
Morning
Mo
:
Use the Programming Worksheet on
the back cover to help with this section.
*Time period programming is only available on Unit Number 1.
Press the MODE button. While holding MODE,
press the UP button for two seconds to enter
time period programming*.
Adjust the start time
for Morning.
Select the day of week.
(Mo - Su)
Adjust the cooling
setpoint for Morning.
(35 - 99 )
Adjust the heating
setpoint for Morning.
(35 - 99 )
Programming a Daily Schedule
Page 9
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Press
MODE
Continued
Start
8 00
Day
Mo
:
Day
85
COOL
o
Am
8 00
Mo
:
Evening
78
COOL
o
Pm
6 00
Mo
:
Start
Pm
6 00
Evening
Mo
:
Day
62
85
HEAT
COOL
o
o
Am
8 00
Mo
:
Adjust the start time
for Evening.
Adjust the start time
for Day.
Adjust the cooling
setpoint for Evening.
(35 - 99 )
Adjust the heating
setpoint for Day.
(35 - 99 )
Adjust the cooling
setpoint for Day.
(35 - 99 )
(Unit # 1 only)Programming a Daily Schedule
Autres manuels pour P474-1100RF
1
Table des matières
Autres manuels Venstar Thermostat
Venstar
Venstar T2700 Manuel utilisateur
Venstar
Venstar T1900 Manuel utilisateur
Venstar
Venstar T2000 Instructions originales
Venstar
Venstar T3900 Guide de démarrage rapide
Venstar
Venstar T0051FS Manuel utilisateur
Venstar
Venstar T2900SCH Manuel utilisateur
Venstar
Venstar T5900 Mode d'emploi
Venstar
Venstar ColorTouch T8800 Guide de dépannage
Venstar
Venstar TSTATCCPB501 Manuel utilisateur
Venstar
Venstar T1045 Manuel utilisateur
Venstar
Venstar T1700 Manuel utilisateur
Venstar
Venstar TSTATEZ Manuel utilisateur
Venstar
Venstar T1700 Manuel utilisateur
Venstar
Venstar T1800 Manuel utilisateur
Venstar
Venstar T1010 Manuel utilisateur
Venstar
Venstar T1050 Manuel utilisateur
Venstar
Venstar T2900 Manuel utilisateur
Venstar
Venstar ColorTouch T6900 Mode d'emploi
Venstar
Venstar T1035 Manuel utilisateur
Venstar
Venstar T1800 Manuel utilisateur
Manuels Thermostat populaires d'autres marques
EWELLY
EWELLY EW-181 Manuel utilisateur
Prolon
Prolon T1100 Instructions d'installation
Computherm
Computherm Q20 Manuel utilisateur
Heatmiser
Heatmiser neoStat Manuel utilisateur
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Manuel utilisateur
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Manuel utilisateur
