Venmar DECO-TOUCH WALL CONTROL Mode d’emploi

6. MOUNT THE WALL CONTROL TO THE WALL.

PLUG THE VENTILATION UNIT AND TEST THE

WALL CONTROL OPERATION.

DECO-TOUCH WALL CONTROL INSTALLATION AND OWNER GUIDE

THIS WALL CONTROL CAN BE USED WITH THE FOLLOWING VENTILATION UNITS:

VENMAR AVS SOLO, DUO, HE, COMPACT, CONSTRUCTO 1.0*, HRV AND ERV EKO 1.5, NOVOFIT, KUBIX HRV PLUS AND KUBIX ERV

VÄNEE GOLD SERIES, HE*, 60H*, HRV AND ERV 90H-V ECM, NOVO+, VIGÖR HRV PLUS AND VIGÖR ERV

IT IS NOT COMPATIBLE WITH OTHER VENTILATION UNITS.

*CONSTRUCTO 1.0 AND VÄNEE 60H BUILT IN AUGUST 2008 AND LATER, AND VÄNEE HE BUILT IN JULY 2006 OR LATER. THE DATE CODE ON

THE UNIT IS PART OF ITS 13-DIGIT SERIAL NUMBER. FOR EXAMPLE, THE SERIAL NUMBER XXXX0708XXXXX, WHERE 07 IS THE YEAR AND

08 THE MONTH (AUGUST); THE DATE CODE IS ALWAYS THE FIFTH, SIXTH, SEVENTH AND EIGHTH DIGITS.

ALWAYS DISCONNECT THE UNIT BEFORE MAKING ANY CONNECTIONS. FAILURE TO DISCONNECT POWER COULD RESULT IN ELECTRIC SHOCK OR DAMAGE

TO THE WALL CONTROL OR ELECTRONIC MODULE INSIDE THE UNIT.

WARNING

FAILURE TO COMPLY WITH THE FOLLOWING CAN CAUSE ERRATIC OPERATION OF THE UNIT:

•NEVER INSTALL MORE THAN ONE MAIN WALL CONTROL PER VENTILATION UNIT.

•KEEP CONTROL LOW VOLTAGE WIRING AT LEAST 1 FOOT (305 MM) AWAYFROMMOTORS, LIGHTING BALLAST, LIGHT DIMMING CIRCUIT AND POWER

DISTRIBUTION PANEL. DO NOT ROUTE CONTROL WIRING ALONGSIDE HOUSE POWER WIRING.

•E

NSURE THE WIRES ARE SECURELY CONNECTED.

CAUTION

WALL CONTROL INSTALLATION

5. STRIP THE END OF THE CABLE TO ACCESS THE

4 WIRES. STRIP THE END OF EACH WIRE.

USING A SMALL FLAT BLADE SCREWDRIVER,

CONNECT EACH WIRE TO ITS CORRESPONDING

TERMINAL ON THE BACK OF THE WALL

CONTROL: YELLOW WIRE TO “Y”, RED WIRE

TO “R”, GREEN WIRE TO “G” AND BLACK

WIRE TO “B”.

VE0243

2. CUT A 2 7/8” X1 ³/8” HOLE IN WALL AT A

CONVENIENT LOCATION FOR THE WALL CONTROL.

ROUTE THE CABLE FROM THE UNIT TO THIS

HOLE.

NOTE:DIMENSIONS SHOWN ARE FOR AN

INSTALLATION WITHOUT WALL BOX.

1. UNPLUG THE VENTILATION UNIT FROM POWER SOURCE.

VC0115

3. TEMPORARILY PLACE THE SWITCH OVER THE

HOLE AND MARK BOTH MOUNTING SCREW

HOLE POSITIONS.

4. REMOVE THE SWITCH, DRILL BOTH SCREW

HOLES (Ø 3/16”) IN WALL AND INSERT WALL

ANCHORS (INCLUDED).

VC0116A

Ø 3/16”, typ.



WALL CONTROL USE

BACKLIGHT

IF THE BACKLIGHT IS NOT ILLUMINATED, THE FIRST BUTTON PRESSED (NO MATTER

WHICH BUTTON) SHALL TURN ON THE BACKLIGHT. THE BACKLIGHT REMAINS ILLUMINATED

FOR 10 SECONDS AFTER THE LAST BUTTON PRESSED.

OPERATING MODES

OFF

PUT THE UNIT ON STAND-BY MODE, SO IT WILL ONLY RESPOND TO

OVERRIDE WALL CONTROLS (IF PRESENT). ONLCD SCREEN, ONLY THE

HOUSE IS VISIBLE SHOWING THE CONTROL IS POWERED ON.

THIS IS THE FACTORY DEFAULT MODE.

RECIRC

AIR IS RECIRCULATED INSIDE THE HOUSE AT HIGH SPEED.

20 MIN/H

THE VENTILATION UNIT EXCHANGES AIR INTERMITTENTLY ON A ONE HOUR

CYCLE AS FOLLOWS: OFF FOR 40 MIN. (OR RECIRCULATION ON

HIGH SPEED FOR 40 MIN., SEE NEXT SECTION ON BACK PAGE) AND

THEN EXCHANGE AIR DURING 20 MIN. ON LOW SPEED. REPEAT CYCLE

AFTER THE 20 MIN. OF AIR EXCHANGE.

MIN

AIR IS EXCHANGED WITH THE OUTSIDE ON LOW SPEED.

MAX

AIR IS EXCHANGED WITH THE OUTSIDE ON HIGH SPEED.

OPERATING MODES (CONT’D)

TO CHANGE THE OPERATION MODE OF THE VENTILATION UNIT, PRESS

THE UP OR DOWN ARROW BUTTON. OPERATING MODE LABEL WILL

THEN SCROLL UP OR DOWN ON LCD SCREEN.

09947 REV. B

WALL CONTROL USE (CONT’D)

HOW TO SET THE RELATIVE HUMIDITY (RH) LEVEL AND CHOOSE BETWEEN

OFF IN STANDBY OR RECIRCULATION IN STAND-BY

SETTING THE RELATIVE HUMIDITY LEVEL ALLOWS TO SELECT THE MAXIMUM DESIRED

INDOOR HUMIDITY LEVEL (IN PERCENTAGE). THIS VALUE WILL BE USED TO START THE

DEHUMIDISTAT OVERRIDE (AIR EXCHANGE IN HIGH SPEED).



PRESS AND HOLD OK FOR 3 SEC. TO

ACCESS THE SETTINGS MENU. THE

BACKLIGHT WILL BE ACTIVATED DURING

ALL THE PROCEDURE.

THE RELATIVE HUMIDITY ARROW AND

VALUE WILL FLASH (DEFAULT SETTING:

45%).

USE UP OR DOWN ARROW

TO CHANGE THE VALUE. THE

VALUE CHANGES BY 1%

INCREMENTS. LOWER VALUE:

30%. UPPER VALUE: 55%.

STILL FLASHING.



PRESS OK BUTTON TO ACCEPT THE

NEW VALUE AND GO TO NEXT SETTTING.

RECIRCULATION ARROWS ARE TURNING

AND rE FLASHES TO SHOW THAT

RECIRCULATION² IS IN STANDBY.



PRESS OK BUTTON

TO ACCEPT AND QUIT

SETTING MENU.



USE UP OR DOWN

ARROW TO CHANGE TO

RECIRCULATION IN

STANDBY.

TWO LINES ARE FLASHING TO SHOW

THAT OFF¹ IS IN STAND BY (DEFAULT

CONFIGURATION SETTING).

RESETTING MAINTENANCE INDICATOR: PRESS SIMULTANEOUSLY ON

BOTH ARROW BUTTONS, MAINTENANCE INDICATOR WILL DISAPPEAR

FROM LCD SCREEN.



AND

MAINTENANCE INDICATOR

THE MAINTENANCE INDICATOR IS REPRESENTED

BY AN M IN A ROUNDED TRIANGLE, AT THE TOP

OF THE HOUSE (SEE BESIDE). IF THIS INDICATOR

IS FLASHING, PERFORM THE SEMI-ANNUAL

MAINTENANCE, AND IF IT IS NOT FLASHING, PERFORM

THE ANNUAL MAINTENANCE (REFER TO THE

VENTILATION UNIT USER GUIDE).

DEHUMIDISTAT OVERRIDE SELECTION

IN THE OPERATING MODES MIN, MAX, 20 MIN/H AND RECIRC, THE USER CAN

SELECT A DEHUMIDISTAT OVERRIDE SO THAT IF THE RELATIVE HUMIDITY (RH) IN THE

HOUSE EXCEEDS THE RH SETTING PREVIOUSLY STORED, THE VENTILATION UNIT WILL

EXCHANGE IN HIGH SPEED UNTIL THE TARGET INDOOR RH SETTING IS REACHED.

AN AIR EXCHANGER IS NOT A DEHUMIDIFIER, BUT IT CAN CHANGE THE INDOOR RELATIVE

HUMIDITY BY BRINGING IN DRIER OR MORE HUMID AIR FROM OUTSIDE DURING NON

HEATING SEASON. THE DEHUMIDISTAT OVERRIDE FUNCTION IS USEFUL TO REDUCE

INDOOR RH WHEN THE OUTDOOR AIR IS COOL AND DRY DURING THE HEATING SEASON.

SELECT A TARGET RH BETWEEN 30% AND 55% ACCORDING TO YOUR COMFORT.

WHEN OUTDOOR RELATIVE HUMIDITY IS HIGH (E.G. IN SUMMER), TURN OFF THE OVERRIDE

BY PRESSING OK UNTIL THE RH DISPLAY DISAPPEARS.

WHEN THE DEHUMIDISTAT OVERRIDE IS ACTIVATED, THE AUTO INDICATOR

WILL APPEAR ON LCD SCREEN TO SHOW THAT THE ACTUAL MODE IS

BEING OVERRIDDEN. ALSO, THE RELATIVE HUMIDITY APPEARS (IF IT WAS

NOT SHOWN, SEE EXAMPLE BESIDE). ONCE THE TARGET HUMIDITY

LEVEL IS REACHED, THE UNIT GOES BACK INTO ITS ORIGINAL OPERATING

MODE AND AUTO DISAPPEARS FROM LCD SCREEN.

NOTE: IF THE ACTUAL MODE IS MAX, ONLY THE RELATIVE HUMIDITY LEVEL

APPEARS ON SCREEN; AUTO LABEL WILL NOT APPEAR.

TO ENGAGE THE DEHUMIDISTAT OVERRIDE, PRESS OK. THE ACTUAL INDOOR RH AND

THE %HUM LABEL APPEAR ON LCD SCREEN.

NOTE: IF THE ACTUAL RH IS LESS THAN 20%, THEN THE HUMIDITY INDICATOR

WILL DISPLAY “LO”, AND IF THE ACTUAL RH IS GREATER THAN 80%, THEN

THE HUMIDITY NDICATOR WILL DISPLAY “HI”.

TO TURN OFF THE DEHUMIDISTAT OVERRIDE, PRESS OK AGAIN. THE RH AND %HUM

DISPLAY WILL DISAPPEAR FROM LCD SCREEN.

POWER FAILURE

AFTER A POWER FAILURE, THE WALL CONTROL RETURNS TO ITS ORIGINAL OPERATION

MODE. ALL SETTINGS ARE KEPT IN MEMORY.

ERROR CODES

IF THERE IS A PROBLEM WITH THE WALL CONTROL, AN ERROR CODE WILL APPEAR ON

THE SCREEN; IT COULD BE E1, E3 OR E7. IS THIS SITUATION OCCURS, UNPLUG THE

VENTILATION UNIT FOR 20 SECONDS AND THEN REPLUG IT. IF THE ERROR CODE IS STILL

PRESENT, PLEASE CALL YOUR INSTALLER.



PRESS OK BUTTON TO ACCEPT AND

QUIT SETTING MENU.

OFF IN STAND BY:ON20 MIN/H MODE, THE VENTILATION UNIT IS OFF DURING

40 MINUTES AND EXCHANGE AIR WITH THE OUTSIDE ON LOW SPEED

DURING THE REMAINING 20 MINUTES OF THE HOUR. THIS IS THE

DEFAULT VALUE.

RECIRCULATION IN STAND BY:ON20 MIN/H MODE, THE VENTILATION UNIT

RECIRCULATES THE INSIDE AIR FOR 40 MINUTES

ON HIGH SPEED AND EXCHANGE AIR WITH THE

OUTSIDE ON LOW SPEED DURING THE REMAINING

20 MINUTES OF THE HOUR.

Autres manuels Venmar Unité de contrôle

Venmar

Venmar DECO-TOUCH WALL CONTROL Mode d’emploi

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur