VBC Racing WildFire Manuel utilisateur

COMPETITION GRADE HIGH PERFORMANCE RADIO CONTROL RACING CAR CHASSIS KIT

1/10 4WD ELECTRIC COMPETITION TOURING CAR KIT

INSTRUCTIONS MANUAL

Thank you for purchasing VBC Racing product.

This VBC Racing kit is a high performance, racing grade car kit

intended for experienced racers. The kit compose of VBC

formulated composite materials, top quality full carbon fiber

chassis and high grade 7075 material which will give you a

competitive edge over the others.

Novice racer should seek advice from more experienced racer

before assembly.

Always keep this instruction manual handy at all times for quick

reference even after completing the assembly.

Before your assembly, sand the chassis edges.

Things that we should remind you.

Sand the chassis edges with #600 sand paper and apply CA

glue to the edges and counter sink holes.

Need help or support.

If you need help or you would like to leave us a comment,

please email to our support team: [email protected] or

visit our web site www.vbcracing.com

BAG MARKED

STEP1

Graphite Edges Protection Procedure

01© VBC Racing WILDFIRE

Sand the chassis edges with #600 sand paper(not included) and

apply CA glue(not included) to the edges of the chassis.

Sand the below graphite edges with #600 sand paper and apply CA glue to the edges.

A-01-VBC-0028 WildFire Graphite Rear Shock Tower

A-01-VBC-0027 WildFire Graphite Front Shock Tower

*Not included in this kit

A-01-VBC-0035-25 WildFire Standard Graphite Chassis

BAG MARKED

STEP2-3

Rear Gear Diff Assembly

Rear Gear Diff Left Side

Rear Gear Diff Right Side

Gear Diff Housing A-03-VBC-0016 x 1

Gear Diff Pulley 38T A-03-VBC-0017 x 1

Diff Gear 18T A-03-VBC-0019 x 2

Diff Cup B-02-VBC-0022 x 2

10x15 Ball Bearing C-02-BB-1510-B x 2

M2x10 Shaft Pin B-02-VBC-0020 x 2

15x0.3 Shim B-02-VBC-0077 x 2

Diff Shaft Sealer O-Ring B-03-VBC-0006 x 2

Rear Gear Diff Right Side Assembly Cross Section

Diff Gear 18T

Diff Outdrive

Right Gear

Diff Housing

Diff Ourdrive

Gear Diff Pulley 38T

Diff Gear 18T

10x15 Ball Bearing

15x0.3 Shim

M2x10 Shaft Pin

Outdrive Sealer O-Ring

10x15 Ball Bearing

M2x10 Shaft Pin

Diff Oil

Apply small amount of diff oil

Diff Outdrive

Diff Gear 18T

Right Gear Diff Housing

10x15 Ball Bearing

15x0.3 Shim

M2x10 Shaft Pin

Outdrive Sealer O-Ring

Diff Oil

Apply small amount of diff oil

15x0.3 Shim

Rear Gear Diff Assembly Continue

Diff Gear 10T A-03-VBC-0018 x 4

M2.6x10 Flathead Screw C-02-SC-F2.6x10 x 4

Seal Gasket B-03-VBC-0004 x 1

03© VBC Racing WILDFIRE

9.5x0.2mm Shim B-02-VBC-0078 x 4

Belt Tension Adjuster Ring A-03-VBC-0047 x 2

Idle Gear 10T Idle Gear 10T

Right Side Diff

Right Side Diff Assembly

Left Side Diff Assembly

Belt Tension Adjuster Ring

STEP2-3

Fill with supplied DIFF TYPE silicon oil

until the gears are fully submerged

9.5x0.2mm Shim 9.5x0.2mm Shim

Diff Gear Shaft A-03-VBC-0020 x 1

Diff Gear Shaft

Diff Housing Sealer O-Ring

Seal Gasket

M2.6x10 Flathead Screw

Place Seal Gasket

to the left side diff

assembly before

putting the right

side diff together

Diff Oil

Diff Housing Sealer O-Ring B-03-VBC-0005 x 1

BAG MARKED

Rear Drivetrain Assembly

Lower Bulkhead A B-02-VBC-0057 x 1

Lower Bulkhead B B-02-VBC-0090 x 1

Motor Mount B-02-VBC-0058 x 1

Main Gear Bulkhead B-02-VBC-0059 x 1

Center Suspension Mount x 2

B-02-VBC-0062

Motor Mount Support B-02-VBC-0067 x 1

Center Suspension Mount Shim(1mm) x 2

A-01-VBC-0038

M3x8 Flathead C-02-SC-F0308 x 1

M3x6 Flathead C-02-SC-F0306 x 13

BAG MARKED

STEP4-6

Lower Bulkhead A

Lower Bulkhead B

Motor Mount

Main Gear Bulkhead

M3x6 Flathead

M3x8 Flathead

Motor Mount Support

Center Suspension Arm

1mm Center Suspension Arm Shim

BAG MARKED

STEP4-6

Front Drive Train Assembly

Lower Bulkhead A B-02-VBC-0057 x 1

Lower Bulkhead B B-02-VBC-0090 x 1

Center Suspension Arm B-02-VBC-0062 x 2

1mm Center Suspension Arm Shim x 2

A-01-VBC-0038

Battery Position Slider A-01-VBC-0033 x 1

Battery Adjust Top Plate x 1

B-02-VBC-0072

M3x8 Flathead C-02-SC-F0308 x 2

M3x6 Flathead C-02-SC-F0306 x 8

Lower Bulkhead A

Lower Bulkhead B

7075 Center Stopper

Graphite Battery Center Stopper

1mm Center Suspension Arm Shim

Center Suspension Arm

M3x6 Flathead

M3x8 Flathead

BAG MARKED

STEP7-9

Steering System Assembly

Steering Assembly Travel Plate B-02-VBC-0054 x 1

Steering Travel Arm B-02-VBC-0053 x 2

Steering Assembly Pole B-02-VBC-0055 x 2

Ball Connector B-02-VBC-0045 x 3

5x8 Ball Bearing C-02-BB-0805-B x 4

3x6 Ball Bearing C-02-BB-0603 x 2

Steering Cone Washer B-02-VBC-0089 x 2

T2 7075 Spacer B-02-VBC-0019-20 x 2

T1 7075 Spacer B-02-VBC-0019-10 x 2

M3x6 Roundhead C-02-SC-R0306 x 4

M3x6 Set Screw C-02-SC-SS-0306 x 1

Ball Connector

3x6 Ball Bearing

M3x6 Set Screw

M3x10 Set Screw

M3x6 Set Screw

Steering Assembly Travel Plate

M3x2.0mm 7075 Spacer

M3x1.0mm 7075 Spacer

M3x6 Roundhead

Graphite Steering Top Plate

Steering Cone Washer

5x8 Ball Bearing

Steering Travel Arm

Steering Assembly Pole

4.50mm

28.30mm

M3x42mm Turnbuckle B-02-VBC-0037 x 2

M3x18mm Turnbuckle B-02-VBC-0038 x 1

Turnbuckle Cup A-03-VBC-0039 x 6

Make 2 steering link tie-rods, follow the connector cups directions as

the above diagram. The connector cups edge to edge shall be 28.20mm.

Please use a caliper to measure the exact measurement

Make 1 servo link tie-rod, follow the connector cups directions as

the above diagram. The connector cups edge to edge shall be 4.50mm.

Please use a caliper to measure the exact measurement

M3x42mm Turnbuckle

Turnbuckle Cup

M3x18mm Turnbuckle

Thead Lock

Right Thread

M3x10 Set Screw C-02-SC-SS-0310 x 2

M3x6 Roundhead

Install the steering unit onto the main chassis with two M3x6 Flathead Screws. Then attach the left and right tie rods to the steering unit.

Make sure the front belt is between the two Steering Assembly Poles.

BAG MARKED

STEP7-9

Steering System Assembly

M3x6 Flathead C-02-SC-F0306 x 2

Front Belt Type SS A-03-VBC-0048-512 x 1

M3x6 Flathead

Optional Steering Stiffener Bar

(A-03-VBC-0078) by VBC Dynamics

sold separately

BAG MARKED

STEP10-14

Upper Deck Assembly

Belt Tensioner B-02-VBC-0069 x 1

3x6mm Ball Bearing C-02-BB-0603 x 2

3x5x0.5mm Shim B-02-VBC-0093 x 3

M3x12 Roundhead Screw C-02-SC-R-0312 x 1

M3x4 Roundhead Screw C-02-SC-R0304 x 1

64P Spur Gear 116T A-03-VBC-SG-116 x 1

20T Center Pulley A-03-VBC-0023 x 2

Center Pulley Spacer A-03-VBC-0060 x 1

Center Pulley Drive Shaft B-02-VBC-0087 x 1

5x8mm Ball Bearing C-02-BB-0805-B x 2

M3x4 Round Head Screw C-02-SC-R0304 x 3

M3x6 Set Screw x 2

C-02-SC-SS-0306

M2x12 Shaft Pin B-02-VBC-0020 x 2

M5x11 E-Clip B-02-VBC-0085 x 2

M3x12 Roundhead

3x6mm Ball Bearing

3x5x0.5mm Shim

3x6mm Ball Bearing

3x5x0.5mm Shim

Belt Tensioner

M3 Lock Nut C-02-SC-NN03 x 1

5x8mm Ball Bearing

M5x11 E-Clip

20T Center Pulley

Center Pulley Drive Shaft

M2x12 Shaft Pin

Center Pulley Spacer

M2x12 Shaft Pin

M3x4 Roundhead

M5x11 E-Clip

5x8mm Ball Bearing

M3x6 Set Screw

Spur Gear

M3x4 Roundhead

116

WildFire Standard Upper Deck A-01-VBC-0026-20

3x5x0.5mm Shim

BAG MARKED

STEP10-14

Upper Deck Assembly

M3x6 Roundhead C-02-SC-R0306 x 12

M3x8 Flathead C-02-SC-F0308 x 1

Antenna Stand A-03-VBC-0059 x 1

Upper Bulkhead A B-02-VBC-0063 x 1

Upper Bulkhead B B-02-VBC-0064 x 1

T2 7075 Spacer B-02-VBC-0019-20 x 2

Ball Connector B-02-VBC-0045 x 2

M3x10 Set Screw C-02-SC-SS-0310 x 2

Rear Upper Bulkhead Assembly

M3x6 Roundhead

M3x8 Flathead

M3x10 Set Screw M3x10 Set Screw

Ball Connector Ball Connector

2mm Spacer 2mm Spacer

Upper Bulkhead A Upper Bulkhead B

Thead Lock

Antenna Stand

Be careful not to overthread the set screw.

The set screw should not over the edge of the bottom of Upper Bulkhead.

Overtheading may obstruct the drive hub from spinning.

Rear Belt Type SS A-03-VBC-0048-177 x 1

Table des matières

Autres manuels VBC Racing Automobile

VBC Racing

VBC Racing Lightning FX Manuel utilisateur

VBC Racing

VBC Racing WildFire D07 Manuel utilisateur

VBC Racing

VBC Racing Lightning 12 Manuel utilisateur

VBC Racing

VBC Racing Ghost EVO Manuel utilisateur

VBC Racing

VBC Racing WildFire D08 Manuel utilisateur

Manuels Automobile populaires d'autres marques

Toyota

Toyota 2000 Tundra Manuel utilisateur

CITROËN

CITROËN DS4 DSign Manuel utilisateur

Lexus

Lexus 2015 CT 200h Manuel utilisateur

Cadillac

Cadillac CTS 2008 Manuel utilisateur

Mercedes-Benz

Mercedes-Benz M-class ML 55 AMG Manuel utilisateur

Porsche

Porsche Boxster S Manuel utilisateur

GMC

GMC 2010 Savana 1500 Cargo Manuel utilisateur

KIAM

KIAM SPORTAGE 2014 Manuel de la liste des pièces

GMC

GMC 2013 Terrain Instructions de montage

GMC

GMC T-Series 1999 Manuel utilisateur

Mercury

Mercury 1998 Mystique Manuel utilisateur

Mercury

Mercury 2007 Mariner Manuel utilisateur

Mazda

Mazda 2007 Mazdaspeed 3 Mode d’emploi

Mazda

Mazda 2014 CX-5 Manuel utilisateur

GMC

GMC Chevrolet Express 2022 Manuel utilisateur

GMC

GMC 1997 Jimmy Manuel utilisateur

Chevrolet

Chevrolet 2012 Malibu Manuel utilisateur

Cadillac

Cadillac 2010 Escalade Manuel utilisateur