Valor GV60CKO Manuel utilisateur

4006080-04

DO NOT USE thermostatic handset supplied with

appliance when installing outdoors!

USE 1265WSK or RBWSK (appliance installed under

overhang)

FIREPLACE

BATTERY

ACCESS

ON-OFF

DOWN

ACCÈS

PILES

DU FOYER

Use with Valor Zero Clearance heater models 530, 534, 650, 1000, 1100, 1150, 1400,

1500, 1600, 1700, 1800 and Insert heater models 700, 738K, 739, 780, 785, RF24KB,

RF24JD installed into existing approved solid-fuel burning fireplaces having weather

protection as specified in this manual.

GV60 Outdoor Fireplace Conversion Kit

INSTALLATION MANUAL

GV60CKO

WARNING

This conversion kit shall be installed by

a qualified service agency in accordance

with the manufacturer’s instructions and

all applicable codes and requirements

of the authority having jurisdiction. If

the information in these instructions is

not followed exactly, a fire, explosion

or production of carbon monoxide may

result causing property damage, personal

injury or loss of life. The qualified service

agency is responsible for the proper

installation of this kit. The installation

is not proper and complete until the

operation of the converted appliance is

checked as specified in the manufacturer’s

instructions supplied with the kit.

Use this manual in conjunction with the

installation manual supplied with the

appliance.

LEAVE THIS MANUAL WITH THE HOMEOWNER.

WARNING

Electrical shock hazard - Do not install

electrical accessories (fans, lighting, wifi)

when converting the appliance for use

outdoors.

General notes regarding conversion

This manual contains instructions for adapting natural

gas or propane models listed above for use outdoors.

For the purpose of this manual the term “outdoor”

means installed outside of the insulated building

envelope within a weatherproof enclosure or existing

solid-fuel burning fireplace having a minimum required

overhang. The outdoor space may be attached or free

standing to the main/primary structure and may or may

not include walls. See page 6 for further information

regarding locating your outdoor fireplace.

Use this manual in conjunction with the installation

manual supplied with the appliance. The outdoor

fireplace must be permanently situated and connected

to a fixed piping system and must not be portable.

Notes

• No electrical accessories (fans, lighting or wifi) per-

mitted when adapting the appliance for outdoor use.

• Any of the optional available trims and fronts may

be used in the outdoor environment including

optional HeatShift components although please

note that some fading or corrosion may occur due to

environmental conditions. Cast iron fronts are not

recommended outdoors.

• Thermostatic controls are not allowed for outdoor

fireplaces. Use the wall switch supplied with the

appliance or when not supplied, order an optional

RBWSK Remote battery and wall switch kit to control

the appliance. Do not use the thermostatic remote

controled handset supplied with the appliance!

1265WSK–

Wall Switch RBWSK–

Remote Batteries &

Wall Switch Kit

Ignition Wire Connection

(spade type connector)

Be careful when removing and

reinstallaing: not to bend or

break the spade connector

Ignition

Wire

Antenna

Replace the existing receiver

Locate the existing receiver on the appliance. The

receiver is held in place by Velcro on most appliances.

Refer to the appliance’s manual if necessary.

1. Detach the receiver and pull it out of the appliance

to disconnect it. Be careful not to pull too hard as

you could damage the wire connections, particularly

the ignition wire connection.

2. Label all wires using the diagram below.

3. Remove all the wires connected to the receiver and

set the receiver aside.

4. Connect the outdoor receiver (G6R-R3AMC) to the

existing wiring. DO NOT INSTALL BATTERIES YET!

Ensure no batteries are installed in the RBWSK

if used. Connections on the outdoor receiver are

identical to the existing receiver. See diagram below.

5. Install and connect the wall switch supplied with

the appliance to the receiver following instructions

provided with the appliance’s installation manual;

if the appliance is not supplied with a wall switch,

connect the RBWSK—Remote battery and wall

switch kit (supplied separately) to the outdoor

receiver—see installation instructions supplied

with the kit.

Valve Wire

Harness

Red

Yellow

Wall Switch

Harness

RBWSK— Remote

Battery Wall

Switch kit power

connector

6. Insert 4 AA alkaline batteries into the outdoor

receiver or the RBWSK kit only after all connections

are completed.

7. Test the operation of the wall switch—see

appliance’s or wall switch kit instructions manual.

IMPORTANT

The connection can

only be done one

way. Do not force it or

damage the pins on

the receiver box!

Take the switch wire and plug it into the receiver’s

connection slot as indicated.

Kit Contents

• 1 GV60 outdoor receiver with conformal coating—

to resist weather—part no. 4005111

• 1 Overlay conversion label—part no. 4006081

• 1 Outdoor Lighting Instructions card—part no.

4005169 G6R-R3AMC—

Outdoor receiver Conversion label and

Lighting Instructions

Caution

DO NOT PUT BATTERIES IN THE REMOTE

CONTROL RECEIVER OR RBWSK until the wires

are connected to the burner control unit as

short-circuit could result in the destruction of the

electrical components.

Caution

DO NOT USE a screwdriver or other metallic

object to remove the batteries from the receiver

or the handset! This could cause a short circuit to

the receiver.

Caution

To avoid short-circuit to the receiver,

position the antenna so that it DOES

NOT TOUCH the ignition wire.

Cleaning AROUND Your Fireplace

Your Valor outdoor gas fireplace will tolerate moderate

amounts of water on an occasional basis but is not

designed to be waterproof.

Ensure the fireplace is turned off - including pilot -

before performing any cleaning around it. Use plastic

sheeting to protect the fireplace front and trim from

direct spray while cleaning. Ensure all plastic is removed

before operating fireplace.

Exposure to outdoor UV light

Exposure to outdoor UV light will cause some plated

and painted finishes to fade over time. This fading is

unavoidable and not covered under warranty.

To minimize fading, locate the fireplace away from direct

sunlight. Decommissioning and covering the fireplace

over the off-season will also prolong the finish.

Decommission During Off-Season

We recommend decommissioning your outdoor

fireplace during the off-season when it will not be used

for an extended period. Decommission your fireplace

by removing the batteries from the battery holder and

turning the gas shut-off valve to the “off” position.

Upon ensuring the fireplace cannot be turned on you

can then apply a weather protective cover over the front

of the fireplace to help preserve the finish and further

protect the appliance from weather.

Note: Do not operate your outdoor fireplace during

cold weather below freezing point

(32°F, 0°C).

Fix the conversion label and replace the

lighting instructions

The data label and lighting information cards are

located either under the firebox near the gas valve or

on the right side of the firebox. They are retained to the

appliance by a wire.

Data label and lighting

instructions located near the

gas valve or to the right of

firebox

1. Fix the conversion label on the data card as

indicated.

2. Remove the existing lighting instructions by cutting

the card out near its fixing point.

3. Staple the new lighting instructions to the data card

near its fixing point.

4. Place back in appliance.

fireplace

data card

lighting

instructions

conversion

label

Supplementary Owner’s Information

Caution

Be careful when using a hose or pressure washing

to clean the areas around the fireplace.

NEVER SPRAY WATER DIRECTLY AT THE

FIREPLACE!

Lighting Instructions for Outdoor Fireplace Use

FOR YOUR SAFETY, READ BEFORE LIGHTING

WARNING: If you do not follow these instructions exactly, a ¿re or explosion may result

causing property damage, personal injury or loss of life.

A. This appliance has a pilot which must be lighted by hand, or wall switch. Follow these instructions exactly. To

save gas, turn the pilot oႇwhen not using the appliance for a prolonged period of time.

B. BEFORE LIGHTING, smell all around the appliance area for gas. Be sure to smell next to the Àoor because

some gases are heavier than air and will settle on the Àoor.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electric switch; do not use any phone in your building.

• Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the ¿re department.

C. Use only your hand to push in or turn the control knobs. Never use tools. If the knobs will not push in or turn by

hand, don’t try to repair them; call a quali¿ed service technician. Force or attempted repair may result in a ¿re or

explosion.

D. Do not use this appliance if any part has been under water. Immediately call a quali¿ed service technician to

inspect the appliance and to replace any part of the control system and any gas control, which has been under water.

LIGHTING INSTRUCTIONS

1. STOP! Read the safety information above.

2. TO CLEAR ANY GAS, turn main valve oႇby pressing ON/OFF on wall switch (1).

• Wait ¿ve (5) minutes to clear out any gas, then smell for gas, including near the Àoor. If you

smell gas, STOP! Follow “B” in the safety information above on this label. If you don’t smell

gas, go to the next step.

3. AUTOMATIC IGNITION: MAN-knob (2) in ON position. Ensure Flame Adjustment

knob (3) is set to lowest setting (3) (Fig. 1). Locate the pilot (Fig. 3.) inside of

¿rebox.

• On the wall switch, press the ON button; a short acoustic signal con¿rms the start

has begun.

• Further short acoustic signals indicate the ignition process is in progress.

• When the pilot is lit, the Flame Adjustment knob (3) will automatically rotate to the

highest setting.

• Press the small Àame button ( ) on the wall switch to reduce the Àame height.

4. MANUAL IGNITION: MAN-knob (2) in MAN position (Fig. 2). With the window oႇ,

locate the pilot (Fig. 3) inside of ¿rebox.

• Set Flame Adjustment knob (3) to the lowest setting (3).

• Push down the metallic core (4) with a pen or similar instrument; this will establish

the pilot gas Àow.

• Light gas at the pilot (5) with a match.

• Continue holding down metal core (4) for about 10 seconds; after release, pilot

should remain lit.

• If the pilot will not stay lit after several tries, turn the gas control knob (3) to OFF (3) and call your local

service technician or gas supplier.

• Reinstall the window and set the MAN-knob (2) to ON; turn Flame Adjustment knob (3) up (4) or down (3)

manually or use the Àame buttons ( )( ) on the wall switch to adjust the Àame height.

TO TURN OFF GAS TO APPLIANCE

AUTOMATIC SHUT-OFF (using the wall switch):

• Press and hold the small Àame button ( ) on the wall switch to shut-oႇthe main burner gas Àow.

• Press ON/OFF button on wall switch to shut-oႇthe appliance, including pilot Àame.

Fig 1

Fig 2

OFF

Fig 3

Spark

Min. required weatherproof

overhang in front and at sides of

replace is 1/2 of the height

of the overhang measured

from the base of the unit

1265WSK Wall switch or

RBWSK Remote battery

& wall switch kit

must be located within

weather protected area

Min. required

overhang

Vertical termination

recommended to

avoid ue products

from accumulating

in outdoor spaces

See appliance

manual and

page 8 of

this manual for

allowable vent

terminal locations

Min. required

overhang

Outdoor replace

installed in

weatherproof

enclosure or existing

solid fuel-burning

replace

Location

For the purposes of this installation

manual the term “outdoor” means

installed outside of the insulated building

envelope within a weatherproof enclosure

or existing solid-fuel burning fireplace

having a minimum required overhang. The

outdoor space may be attached or free

standing to the main/primary structure

and may or may not include walls.

Note: The fireplace will not perform

as an exterior wall. If installed against

an exterior wall we recommend the

appliance enclosure or chase be

constructed completely outside of the

insultated building envelope and weather

membrane.

The fireplace must be permanently

situated and connected to a fixed piping

system, it is not portable.

Weather Protection/Moisture

Resistance

This outdoor fireplace will tolerate

moderate amounts of water on an

occasional basis but is not waterproof.

The fireplace must be enclosed in a

existing solid-fuel burning fireplace or

weatherproof enclosure clad in typical

weatherproof material such as siding/

stucco/stone/tile, etc. and have a

weatherproof structure to shed water

that extends horizontally beyond the front

and side perimeter of the fireplace (see

diagram).

Water running down vertical surfaces

should be directed away from the fireplace

using flashings. Measures must be taken

to ensure any accumulated water drains

away from the fireplace and structure.

When the fireplace is installed on surfaces

where water may collect or cause damage

a suitable drainage pan should be placed

under the unit and the water drained away.

Top View (typical)

Side View (typical)

Min. weatherproof overhang

in front and at sides

Min. weatherproof overhang

in front and at sides

Free standing structure

with weatherproof

overhang above

Weatherproof enclosure or

existing solid-fuel burning

replace

Weatherproof

enclosure

Existing approved solid-fuel

burning replace

Gas replace

insert

1600

See-

through

Continuous insulated building envelope and weatherproof

membrane is NOT interrupted by replace installation

INSIDE

OUTSIDE

Min. weatherproof overhang

in front and at sides

Sidewall vent terminations

within 7’ of grade or

where easily accessible

require a terminal guard

DO NOT INTERRUPT

BUILDING ENVELOP

WITH ZERO CLEARANCE

GAS FIREPLACE

INSTALLATION!

See appliance

manual and

page 8 of

this manual for

allowable vent

terminal locatio

Typical Location

Combustible Overhang—Left Side View

All models

Bottom of appliance

Do not put

furniture or objects

within 36” (914 mm)

of front of appliance

Min. required

weatherproof

overhang

Combustible Overhang

54” Min. to Combustible Overhang

(non-combustible construction permited lower)

Note: Use of the optional

HeatShift®System Kits

affects mantel and hearth

clearances.

See instructions in fireplace’s

Installation manual.

not to scale

Horizontal Vent Terminal Locations

(see appliance manual for allowable vertical terminal locations)

• This direct vent appliance is designed to operate when

an undisturbed airflow hits the outside vent terminal

from any direction.

• The minimum clearances from this terminal that must

be maintained are shown in the figure below. Any reduc-

tion in these clearances could result in a disruption of

the airflow or a safety hazard. Local codes or regulations

may require greater clearances.

• The vent terminal must not be recessed into a wall

or siding.

• The vent terminal should be positioned where it will

not be covered by snowdrifts.

• Sidewall vent terminations within 7’ of grade or where

easily accessible require a terminal guard such as the

Valor 658TG or 845TG.

Vent Termination

• The vent terminal must be located on a side wall or

through the roof. Where possible, venting through the

roof is preferable to sidewall venting to avoid products

of combustion from accumulating in outdoor spaces.

• Typically, outdoor spaces are not totally enclosed by sol-

id continuous walls. When sidewall venting is used, the

vent terminal will need to be located to avoid products

of combustion from accumulating within the outdoor

space or from entering the interior space through doors

and windows. See clearances listed below with respect to

openings to interior spaces.

• When a sidewall vent terminal terminates below an

overhead cover (either permanent or temporary cover)

at least 30% of the total perimeter wall area surrounding

the outdoor space must be openings.

KEY VENT TERMINAL LOCATIONS - MINIMUM DISTANCES

Measured from the center of vent

MINIMUM

CLEARANCE

Inches Cm

A Clearance above grade, verandah, porch, deck or balcony 12 30

B Clearance to window or door that may be opened 12 30

C Clearance to permanently closed window (recommended to prevent condensation on window) 12 30

DVertical clearance to ventilated soɝt located above the terminal within a horizontal distance of 2 feet (60 cm)

from the center-line of the terminal 18 46

E Clearance to unventilated soɝt 12 30

F Clearance to outside corner 12 30

G Clearance to inside corner 12 30

HHorizontal clearance to center-line of meter/regulator assembly located within 15 feet (4.6bm) below the

terminal 36 90

IClearance to service regulator vent outlet 36 90

J Clearance to non-mechanical air supply inlet to the building or the combustion air inlet to any other appliance 12 30

K Clearance to a mechanical air supply inlet 72 180

Clearance above paved sidewalk or a paved driveway located on public property

Note: A vent must not terminate directly above a sidewalk or paved driveway, which is located between two single-

family dwellings and serves both dwellings. THIS DOES NOT APPLY to direct vent, non-consdensing appliances in

the Province of Ontario.

84 210

MClearance under a verandah, porch, deck or balcony

Only permitted if veranda, porch, deck or balcony is fully open on a minimum of 2 sides beneath the ȵoor 12 30

Note: Local codes and regulations may require di΍erent clearances.

Min. 72”

Max. 72”

Alcove detail

(open on one

side) Normal

ceiling/soɝt

clearances

apply.

Valor®Outdoor Installation Warranty

If you have a problem with this unit, please contact your dealer or supplier immediately. Under no circumstances

should you attempt to service the unit in any way by yourself. The warranties in paragraphs 1 are provided

only to the initial owner of this unit, are not transferable and are subject to the conditions and limitations in

paragraphs 2 and 3. Please review the conditions and limitations carefully and strictly follow their requirements.

1. Two-Year Parts Warranty

Two (2) years from the date of purchase, the

Company, at its option, will repair or exchange

all parts and components that are found to have

a bona ȴde defect in material or workmanship

under normal conditions of use.

2. Conditions and Limitations

a) The warranty registration card must be

completed by the initial owner and returned

to the company within 90 days. Alternatively,

the warranty registration form may be

ȴlled out online at valorȴreplaces.com

b) Installation and maintenance must be performed

by an authorized and trained dealer in accordance

with the Company’s installation instructions.

c) This warranty is void where installation of the

unit does not conform to all applicable codes,

including national and local gas appliance

installation codes and building and ȴre codes.

d) The owner must comply with all

operating instructions.

e) The Company is not responsible for the

labor costs to remove defective parts or re-

install repaired or replacement parts.

f) The initial owner of the unit will be responsible

for any shipping charges for replacement

parts as well as travel time incurred by the

dealer to perform the warranty work.

g) This warranty applies to non-commercial use and

service and is void if it is apparent that there is

abuse, misuse, alteration, improper installation,

accident or lack of maintenance to the unit.

h) This warranty does not cover

damage to the unit due to:

i) Improper installation, operational

or environmental conditions.

ii) Inadequate ventilation in the area

or competition for air from other

household equipment or appliances.

iii) Damage due to chemicals, dampness,

condensation, or sulphur in the fuel supply

lines which exceeds industry standards.

i) This warranty does not cover glass, log breakage

or damage to the unit while in transit.

j) The Company does not allow anyone to extend,

alter or modify this warranty and assumes no

responsibility for direct, indirect or consequential

damages caused by the unit. State or provincial

laws where the initial owner or user resides may

provide speciȴc rights extending this warranty

and, if so, the Company’s sole obligation

under this warranty is to provide labor and/

or materials in accordance with those laws.

3. No Other Warranty

All obligations to repair this unit are deȴned in

this warranty. Some states or provinces may

speciȴcally mandate additional obligations on

the part of manufacturers, but in the absence

of such speciȴc legislation, there is no other

warranty or obligation expressed or implied.

190ɋ–ɋ2255 Dollarton Highway,

North Vancouver, BCɄCanadaɄV7H 3B1

warranty wor

NE PAS UTILISER la manette de télécommande

thermostatique avec le foyer installé à l’extérieur!

UTILISEZ LE 1265WSK ou RBWSK (installé dans un

endroit couvert)

Concernant la conversion

Ce guide contient les directives pour adapter les foyers

indiqués ci-dessus, soit au gaz naturel ou propane, pour

usage à l’extérieur. Pour ce guide, le terme “extérieur”

désigne un foyer installé à l’extérieur des murs de l’édifice

dans un espace à l’épreuve des intempéries ou dans un

foyer à combustibles solides certifié existant et couvert

d’un surplomb minmal exigé. L’espace extérieur peut être

adjacent ou séparé de la structure principale de l’édifice et

peut inclure des murs. Voir page 15 pour plus de rensei-

gnements concernant l’emplacement du foyer extérieur.

Utilisez ce guide conjointement avec le guide d’installation

fourni avec le foyer. Le foyer extérieur doit être situé de

façon permanente dans son emplacement et doit être rac-

cordé à un réseau fixe de tuyaux et ne doit pas être portatif.

Notes

• Aucun accessoire électrique (ventilateur, éclairage ou

wifi) permis lorsque le foyer est adapté pour l’extérieur.

• Toutes bordures ou devantures optionnelles peuvent

être utilisées dans un environnement extérieur; toute-

fois, veuillez noter que la couleur peut changer et il peut

y avoir de la corrosion dus aux conditions climatiques.

Les devantures de fonte ne sont pas recommandées

à l’extérieur.

• Les commandes thermostatiques ne peuvent pas

être utilisées sur les foyers extérieurs. N’utilisez que

l’interrupteur mural fourni avec le foyer ou, lorsque non

fourni, commandez le Porte-piles et interrupteur mural

RBWSK pour contrôler le foyer. NE PAS UTILISER la

manette thermostatique de télécommande fournie

avec l’appareil!

1265WSK–

Interrupteur

mural

RBWSK–Porte-piles

et Interrupteur

mural

Utilisez avec les foyers Valor à dégagement zéro (ZC) 530, 534, 650, 1000, 1100,

1150, 1400, 1500, 1600, 1700, 1800 et encastrables 700, 738K, 739, 780, 785, RF24KB,

RF24JD installés dans un foyer à combustibles solides certifié existant protégés des

intempéries tel que décrit dans le présent guide.

GV60 Conversion pour foyer extérieur

GUIDE D’INSTALLATION

GV60CKO

XX FIREPLACE

BATTERY

ACCESS

ON-OFF

DOWN

ACCÈS

PILES

DU FOYER

AVERTISSEMENT

Ce trousse de conversion doit être

installée par une agence de service

qualifiée selon les directives du fabricant

et tous les codes et règlements applicables

dans la juridiction de l’installation. Dans

les cas ou les directives de ce guide ne

seraient pas suivies à la lettre, un feu, une

explosion ou la production de monoxide

de carbone pourraient se produire et

causer des dommages matériels, des

blessures ou la mort. L’agence de service

qualifiée pour effectuer cette installation

est responsible de l’installation appropriée

de ce kit. L’installation n’est complète que

lorsque l’opération de l’appareil converti

a été vérifiée tel qu’indiqué par les

directives du fabricant fournies avec

cette trousse.

Utilisez ce guide en conjonction avec le

guide d’installation fourni avec le foyer.

LAISSEZ CE GUIDE AU CONSOMMATEUR.

AVERTISSEMENT

Risque de choc électrique - Ne pas installer

d’accessoires électriques (ventilateur,

éclairage, wifi) lorsque le foyer est

converti pour usage à l’extérieur.

Autres manuels pour GV60CKO

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Valor Accessoires de cheminée

Valor

Valor G3 Series Manuel utilisateur

Valor

Valor G3.5 Series Manuel utilisateur

Valor

Valor 1600J L1 Manuel utilisateur

Valor

Valor G3 Series Manuel utilisateur

Valor

Valor L1 Series Manuel utilisateur

Valor

Valor H3 Series Manuel utilisateur

Valor

Valor 546LFB Manuel utilisateur

Valor

Valor Legend G3 Manuel utilisateur

Valor

Valor 748CTK-VIK Manuel utilisateur

Valor

Valor 715CVI Manuel utilisateur

Valor

Valor LEGEND G3 BSK742 Manuel utilisateur

Valor

Valor Madrona BSKMF01 Manuel utilisateur

Valor

Valor 785KNGK Manuel utilisateur

Valor

Valor H6 Series Manuel utilisateur

Valor

Valor GV60WIFI Manuel utilisateur

Valor

Valor 614CVI Manuel utilisateur

Valor

Valor Legend G3 739NGK Manuel utilisateur

Valor

Valor ZERO CLEARANCE KIT Manuel utilisateur

Valor

Valor LX2 Series Manuel utilisateur

Valor

Valor H5 1184ECAS Manuel utilisateur

Valor

Valor SFFK01 Manuel utilisateur

Valor

Valor Madrona Manuel utilisateur

Valor

Valor 1430CIK Manuel utilisateur

Valor

Valor L1 Series Mode d’emploi

Manuels Accessoires de cheminée populaires d'autres marques

Exodraft

Exodraft Xzense Manuel utilisateur

Whalen

Whalen Ruso MNFP62BF23-6 Manuel utilisateur

Lopi

Lopi Hearthview 864 Manuel utilisateur

Woodstock Soapstone

Woodstock Soapstone Fireview 201 Manuel utilisateur

EdilKamin

EdilKamin SERBATOIO 250 Guide de démarrage rapide

Bronpi

Bronpi KIT-1 Manuel utilisateur

Town & Country Fireplaces

Town & Country Fireplaces 22150051 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Superior

Superior ASD3628-TI Manuel utilisateur

pleasant hearth

pleasant hearth OFP28WG Manuel utilisateur

IHP

IHP Astria Series Manuel utilisateur

Firegear

Firegear FG-H-2110SS Manuel utilisateur

Nibe

Nibe Contura C i31 Manuel utilisateur

kozy heat

kozy heat KZK-052 Manuel utilisateur

SimpliFire

SimpliFire SF-WM36 Manuel utilisateur

Bluegrass Living

Bluegrass Living BC18NR Guide de démarrage rapide

pleasant hearth

pleasant hearth IRIS SCROLL Manuel utilisateur

Cooke

Cooke Glass Wind Guard Manuel utilisateur