Ursalink UG87 Manuel utilisateur
1
UG87-Out LoRaWAN Gateway
Quick Start Guide
Ursalink Technology Co., Ltd.
www.ursalink.com
1
Welcome
Thank you for choosing Ursalink UG87 LoRaWAN Gateway.
This guide teaches you how to install the UG87 (Outdoor) and how to log in the web GUI to configure the
device. Once you complete the installation, refer to the Ursalink UG87 User Guide for instructions on how to
perform configurations on the device.
Related Documents
This Quick Start Guide only explains the installation of Ursalink UG87 LoRaWAN Gateway. For more
functionality and advanced settings, please refer to the relevant documents as below.
Document
Description
Ursalink UG87 Datasheet
Datasheet for the Ursalink UG87 LoRaWAN Gateway.
Ursalink UG87 User Guide
Users can refer to the guide for instruction on how to log in the
web GUI, and how to configure all the settings.
The related documents are available on Ursalink website: http://www.ursalink.com.
Declaration of Conformity
UG87 is in conformity with the essential requirements and other relevant provisions of the CE, FCC, and
RoHS.
For assistance, please contact
Ursalink technical support:
Email: support@ursalink.com
Tel: 86-592-5023060
Fax: 86-592-5023065
Ursalink UG87 Quick Start Guide
www.ursalink.com
2
Before you begin to install the UG87 LoRaWAN Gateway, please check the package contents to verify that
you have received the items below.
1.1 Package Contents
Optional Accessories
1 × Pole Mount A + 2 × U-Bolt
1 × Pole Mount B + 2 × U-Bolt
Screws
Required Additional Equipment
If any of the above items is missing or damaged, please contact your Ursalink sales
representative.
1 × UG87
1 × Ethernet Extension Cord
1 × Water-proof Connector
1 × Power Supply Cable
2 × Cellular Antennas
1 × LoRa Antenna
1 × GPS Antenna
1 × Warranty Card
1 × Quick Start Guide
1 × Wall Mounting Kit
2 × Pole Mounting Kit
Screws
1 × Personal Computer
1 × Ethernet Cable
1 × Wrench M6
2 × Screwdrivers
( Phillips-head and Flathead )
1. Packing List
+
+
Ursalink UG87 Quick Start Guide
www.ursalink.com
3
2.1 Overview
2.2 Dimensions (mm)
2. Hardware Introduction
Top View Bottom View Front & Rear View
Ursalink UG87 Quick Start Guide
www.ursalink.com
4
2.3 LED Indicators
LED indicators are on the front panel of device.
LED
Indication
Status
Description
POWER
Power Status
On
The power is switched on
Off
The power is switched off
STATUS
System Status
Green Light
Static: Start-up
Blinking slowly: the system is running properly
Off
The system goes wrong
LoRa
LoRa Status
Green Light
Packet Forwarder mode is running well.
Off
Packet Forwarder mode is running off.
VPN
VPN Status
Green Light
VPN is connected
Off
VPN is disconnected
SIM1/SIM2
SIM Card Status
Off
SIM1 or SIM2 is registering or fails to register (or
there are no SIM cards inserted)
Green Light
Blinking slowly: SIM1 or SIM2 has been registered
and is ready for dial-up
Blinking rapidly: SIM1 or SIM2 has been registered
and is dialing up now
Static: SIM1 or SIM2 has been registered and dialed
up successfully
Signal
Strength
Signal 1/2/3
Off
No signal
Green Light
Static/Off/Off: weak signals with 1-10 ASU (please
check if the antenna is installed correctly, or move
the antenna to a suitable location to get better
signal)
Static/Static/Off: normal signals with 11-20 ASU
(average signal strength)
Static/Static/Static: strong signals with 21-31 ASU
(signal is good)
2.5 Reset Button
Reset button is on the front panel of device.
Function
Description
STATUS LED
Action
Reboot
Blinking
Press and hold the reset button for about 5-15 seconds.
Static Green
Release the button and wait for system to reboot.
Reset
Blinking
Press and hold the reset button for more than 15 seconds.
Static Green →
Rapidly Blinking
Release the button and wait.
Off → Blinking
The gateway is now reset to factory default.
Ursalink UG87 Quick Start Guide
www.ursalink.com
5
2.6 Ethernet Port Indicator
Ethernet port indicators are on the front panel of device.
Indicator
Status
Description
Link Indicator (Orange)
On
Connected
Blinking
Transmitting data
Off
Disconnected
Rate
Indicator (Green)
On
1000 Mbps mode
Off
100 Mbps mode
Ursalink UG87 Quick Start Guide
www.ursalink.com
6
Environmental Requirements
- Power Input: 100-240VAC (Option: 9-48 VDC)
- Power Consumption: Typical 3.3W (Max 6.4 W)
- Ingress Protection: IP67
- Operating Temperature: -40°C to 70°C (-40°F -158°F)
- Relative Humidity: 0% to 95% (non-condensing) at 25°C/77°F
3.1 SIM Card Installation
3.1.1 Remove the detachable cover
Remove the detachable cover of the housing with a screwdriver (M4).
Note: Your device has been installed into the enclosure before delivery.
3.1.2 SIM Card Installation
A. Push the yellow button on the left panel of the B. Put SIM card onto the slot then insert the
slot, and then you will see the SIM card back into the hole.
slot popping out directly.
3. Hardware Installation
Ursalink UG87 Quick Start Guide
www.ursalink.com
7
3.2 Antenna Installation
3.2.1 Remove the protective caps
Remove the protective caps from the antenna connectors. Take cellular connector as an example.
3.2.2 Connect the antenna
Connect the antenna to the corresponding antenna connector by holding on the metal part of the antenna
and rotating it clockwise.
Note: Each antenna is labeled as 3G, 4G or LoRa.
3.3 Power Connection
3.3.1 Remove the protective caps
Locate the power port marked POWER on the left side of the enclosure and remove the protective cap to
find the connection pins.
Ursalink UG87 Quick Start Guide
www.ursalink.com
8
3.3.2 Connect the power cable
Connect a power supply cable to the power port, and rotate it clockwise.
3.4 Ethernet Connection
1. Get the network cable through the screw nut, rubber ring and the screw bolt;
2. Insert the rubber ring into the screw bolt;
3. Connect the screw nut to the screw bolt;
4. Place the O-Ring on the network port connector;
5. Connect the RJ45 to the Network port connector, and tighten the screw bolt and the connector.
PIN
Color
Description
1
Brown
L (VIN+)
2
Black
GND
3
Blue
N (VIN-)
Ursalink UG87 Quick Start Guide
www.ursalink.com
9
3.5 Connect UG87 to a Computer
3.6 Mount Gateway
The gateway can be mounted to a wall or a pole.
3.6.1 Wall Mounting
Make sure you have mounting bracket, bracket mounting screws, wall plugs, wall mounting screws and
other required tools.
1. Before you start, make sure that your SIM card has been inserted, your antennas have been attached and
that all cables have been disconnected from your enclosure.
2. Mount the enclosure to the mounting bracket with the bracket mounting screws.
3. Align the mounting bracket horizontally to the desired position on the wall, use a marker pen to mark
four mounting holes on the wall, and then remove the mounting bracket from the wall.
Note: The connecting lines of adjacent points are at right angles.
4. Drill the four holes with a depth of 32 mm by using your drill with a 6 mm drill bit on the positions you
marked previously on the wall.
5. Insert four wall plugs into the holes respectively.
6. Mount the mounting bracket horizontally to the wall by fixing the wall mounting screws into the wall
plugs.
Note: Place the power port on the button when installing.
Autres manuels pour UG87
1
Table des matières
Autres manuels Ursalink Porte
Ursalink
Ursalink UG85 Manuel utilisateur
Ursalink
Ursalink UR75 Edge Manuel utilisateur
Ursalink
Ursalink UG87-LW Manuel utilisateur
Ursalink
Ursalink UG65 Manuel utilisateur
Ursalink
Ursalink urbana GI01 Manuel utilisateur
Ursalink
Ursalink UG87-In Manuel utilisateur
Ursalink
Ursalink UG85 Manuel utilisateur
Ursalink
Ursalink UG87 Manuel utilisateur
Ursalink
Ursalink LoRa Manuel utilisateur
Manuels Porte populaires d'autres marques
LST
LST M500RFE-AS Manuel utilisateur
Kinnex
Kinnex Media Gateway Manuel utilisateur
2N Telekomunikace
2N Telekomunikace 2N StarGate Manuel utilisateur
Mitsubishi Heavy Industries
Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuel utilisateur
ZyXEL Communications
ZyXEL Communications ZYWALL2 ET 2WE Manuel utilisateur
Telsey
Telsey CPVA 500 - SIP Manuel utilisateur
