Universal Tool UT8941 Manuel utilisateur

INSTRUCTION MANUAL - ENGLISH

Air Auto Shut-Off Pistol Screwdriver

This product is designed for installing and removing threaded fasteners in wood, metal and

plastic. The use of spare parts/ accessories other than those originally supplied by the

manufacturer may result in a drop in performance and/or increased maintenance / noise

level / vibrations. As a result, the full cancellation of the manufacturer’s liability. No other

use is permitted. Professional use only.

Air Supply Requirements

1. Supply tool with 6.35 KG/CM2(90 PSI) clean and dry air. Too much pressure drastically

reduces the tool life.

2. Connect the tool to air line using pipe, hose and fitting sizes shown in the diagram below.

Lubrication

1. Use an air line lubricator with SAE #10 oil. Adjustedto two (2) drops per minute. If an air

line lubricator is not available, add air motor oil to the inlet once a day.

2. For gearing and clutch, use Shell-grade grease containingmolybdenum.

3. Grease clutches every 12,000 screws.

Torque Adjustment

Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing which is

to be tightened. The motor will start and tighten the fixing to the required torque set by

adjusting the tension on the clutch spring. At this point, the internal drive is disengaged and

the air to the motor cut off.

Operating Procedures

Air-inlet

Right/Left Switch

Torque Cover

Bit Retainer Sleeve

Trigger

1. Make sure the air in air line is clean and dry.

2. There are three air-inlets on the tool. Depending on different usage, choose one inlet to

connect correctly with the air compressor. Screw up the other two air-inlets separately

with screw caps.

3. Install a bit (as illustrated below). Before using, do check the bit being installed on the

tool correctly.

4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring right

(clockwise) to increase the torque. Turn the torque adjustment ring left

(counter-clockwise) to reduce the torque. After setting up the torque, put torque cover

back and fasten it tightly to avoid changing set-up accidently. (as illustrated below)

5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening screws.

Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.

6. Two ways to operate:

A. Push + Pull The Trigger to Start: Set the bit aiming the screw. Push down the tool

steadily and pull the trigger to activate the motor. When the required torque is reached,

the motor will shut off automatically. Either releasing the trigger or take the tool away

from the fixing will stop the motor. (Dual security design)

B. Push to Start: Press the trigger and push the “Locking” switch to the right to lock the

trigger. Push down the tool steadily to activate the motor. The operation can be repeated

without pulling trigger constantly. When the required torque is reached, the motor will

shut off automatically.

7. Suggestion: Correct / Re-set torques before operation on a daily basis.

8. If the tool is not to be used for a long time, re-set the torque to the lowest.

Press & Lock

1234

Switch Operation of Three Way Air-inlet

Installation of Bit

Press the sleeve softly

Insert a bit

Make sure the bit

is fixed tightly

Shut off

123

Set-up of Torque

Operation of R/L Switch

12 3

678

12 3

678

1L 2L

Shut off 1R 2R

Turn clockwise to

increase the torque

Take off the

adjustment ring

Put the torque

cover back

Fasten the rear

housing tightly

Release and remove the torque cover

Insert torque

adjustment ring to

the tool

Turn counter clockwise

to lower the torque

R Indication –turn right (clockwise)

–fastening screw

L Indication –turn left (counter

clockwise) –loosening screw

1L 2L

1R 2R

1L 2L

1R 2R

UT8941 AUTO SHUT-OFF PISTOL SCREWDRIVER, 700rpm / 0.5~4.0Nm

INDEX NO.

PARTS NO.

DESCRIPTION QTY/SET

INDEX NO.

PARTS NO.

DESCRIPTION QTY/SET

17120001PS REAR HOUSING 146 7120043PS END PLATE 1

27120061PS-W TORQUE COVER 147 R-1340HH BALL BEARING 1

37120070PG HOUSING CAP 148 7120048PG VALVE 1

47160002PS C RING 149 OR0602 O-RING 1

57120003PS BIT RETAINER SLEEVE 150 7120063PG-BK MOTOR HOUSING 1

67120004PS SPRING 251 7160052PS SCREW 1

77120005PS TORQUE RING 152 7120051PG-RD SWITCH 1

87160006PS REGULATION WASHER 153 HEXM806 SCREW 1

97120007PS NEEDLE 354 7120067PG SCREW CAP 2

10 7120008PS CLUTCH HOUSING 155 OR1898 O-RING 3

11 7120009PS ANVIL BUSHING 156 HEXM308 SCREW 4

12 7120010PS WASHER 157 7120069PG VALVE BUSHING 1

13 7145011PS TORQUE SPRING 158 589058 O-RING 2

14 7120012PS ANVIL 159 7120054PS OPERATING ROD 1

15 7160013PS STEEL BALL 160 OR0302 O-RING 2

16 7160014PS STEEL BALL 261 7160056PS VALVE PLATE 1

17 7120016PS SLIDE BASE 162 7160057PS SPRING 1

18 7120064PS C RING 163 7120068PG SCREW 1

19 7120018PS BALL RACE 164 OR0612 O-RING 3

20 7160019PS STEEL BALL 53 65 7120076PG PLUG 1

21 7120020PS END CLUTCH 166 611239-1 SPRING 1

22 7120021PS CENTER CLUTCH 167 SB0003-1 STEEL BALL 1

23 STB3175 STEEL BALL 268 7120075PG TRIGGER LOCKING 1

24 7120023PS REAR CLUTCH 169 7120073PG SPRING 1

25 7120024PS RETAINER 170 7120065PG TRIGGER PIN 1

26 7160017PS C RING 171 OR0312 O-RING 1

27 7120025PS PILOT PIN 172 7120066PG BUSHING 1

28 B6901ZZ BALL BEARING 173 7120074PG TRIGGER 1

29 7120027PG CENTER HOUSING 174 SPP0214 SPRING PIN 1

30 7145029PS GEAR CAGE 175 7120072PG GRIP 1

31 7145030PS PIN 476 OR2402 O-RING 1

32 7145031PS PLANETARY GEAR 477 ZZ389507 SILENCER 1

33 7145032PS SUN GEAR 178 7120071PG EXHAUST DEFLECTOR 1

34 7160033PS GEAR CAGE 179 861432-3 SCREW 1

35 7145034PS PIN 480 7120062PG AIR INLET 1

36 7145035PS PLANETARY GEAR 481 7160080PS DISTINGUISHABLE RING(4) 1

37 7120036PS INTERNAL GEAR 182 7160064PS TORQUE ADJUSTMENT RING 1

38 RTW-16 C RING 183 CP1HP60 SUSPENSION RING 1

39 L-1680HH BALL BEARING 1

40 7120039PG FRONT PLATE 1

41 308013 SPRING PIN 1

42 7120041PS BLADE 5

43 7120040PS ROTOR 1

44 7120042PS CYLINDER 1

45 SPP0208 SPRING PIN 2

UT8941 AUTO SHUT-OFF PISTOL SCREWDRIVER, 700rpm / 0.5~4.0Nm

Division of Florida Pneumatic Mfg Corp.,

851 Jupiter Park Lane,

Jupiter, FL 33458, USA.

Ph: (1) 561 744 9500

Fax: (1) 561 575 5574

EC/UKCA DECLARATION OF CONFORMITY

We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA

Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:

MachineType: UT8941 AirAutoShut-Off Screwdriver

TechnicalData:

ChuckSize: 1/4”HEXQC FreeSpeed: 700 rpm

Weight: 0.76 kg(1.68lbs) Length: 192 mm(7.56”)

Recommended HoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)

Noise: (soundpressurelevel) 72dB(A) Vibration: 1.81Metres/Sec ²

Spindlesize: N/A Serial No: ________________

Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,General

SafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO28927,Noise:ISO

15744:2008

Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development

--------------------------------------------------------------------------------

Autres manuels Universal Tool Tournevis électrique

Universal Tool

Universal Tool UT8962-11 Manuel utilisateur

Universal Tool

Universal Tool UT8933 Manuel utilisateur

Universal Tool

Universal Tool UT2960A Manuel utilisateur

Universal Tool

Universal Tool UT8962-17 Manuel utilisateur

Universal Tool

Universal Tool UT8958 Caractéristiques techniques

Universal Tool

Universal Tool UT8931 Manuel utilisateur

Universal Tool

Universal Tool UT8955 Manuel utilisateur

Universal Tool

Universal Tool UT8963ATT-11 Manuel

Universal Tool

Universal Tool AINA PTT Caractéristiques techniques

Universal Tool

Universal Tool UT8226 Caractéristiques techniques

Universal Tool

Universal Tool UT8943 Manuel utilisateur

Universal Tool

Universal Tool UT8963-17 Manuel utilisateur

Universal Tool

Universal Tool UT8963ATT-5 Manuel

Universal Tool

Universal Tool UT8955 Caractéristiques techniques

Universal Tool

Universal Tool UT8965 Manuel utilisateur

Universal Tool

Universal Tool UT8932 Manuel utilisateur

Universal Tool

Universal Tool UT2960A Manuel

Universal Tool

Universal Tool UT8963 Manuel utilisateur

Universal Tool

Universal Tool UT8934 Manuel utilisateur

Universal Tool

Universal Tool UT8960-2 Manuel

Universal Tool

Universal Tool UT8906 Caractéristiques techniques

Universal Tool

Universal Tool UT8963AT-11 Manuel utilisateur

Universal Tool

Universal Tool UT8818-S Manuel

Universal Tool

Universal Tool UT8963AT-17 Manuel utilisateur

Manuels Tournevis électrique populaires d'autres marques

Makita

Makita DFT085F Manuel utilisateur

Parkside

Parkside 345138 2004 Manuel utilisateur

Makita

Makita DFL650F Manuel utilisateur

AEG

AEG BST 18BLX2-0 Manuel utilisateur

Ingersoll-Rand

Ingersoll-Rand D5000 Series Manuel utilisateur

BGS technic

BGS technic 956 Manuel utilisateur

Hilti

Hilti SD 6000 Manuel utilisateur

Parkside

Parkside PEPS 3 A1 Manuel utilisateur

Festool

Festool TI 15 Manuel utilisateur

Makita

Makita DWT190 Manuel utilisateur

Matatakitoyo Torque Tools

Matatakitoyo Torque Tools MTD Manuel utilisateur

Skil

Skil 2346 Instructions de montage

DeWalt

DeWalt XR LI-ION DCD931 Manuel utilisateur

Festool

Festool DWC 18-2500 Manuel utilisateur

EINHELL

EINHELL TE-CD 12/1 Li Series Manuel utilisateur

Makita

Makita BFT043F Manuel utilisateur

Stanley

Stanley SCD2 Manuel utilisateur

Atlas Copco

Atlas Copco LUM12 SR Feuille d'instructions