Universal Tool UT8934 Manuel utilisateur
1
INSTRUCTION MANUAL
Air Auto Shut-Off Straight Screwdrivers
This product is designed for installing and removing threadedfasteners in wood, metal,
and plastic. The use of spare parts/accessories other than those originally supplied by
the manufacturer may result in a drop in performance and/or increased
maintenance/noise level/vibrations, and as the result, the full cancellation of the
manufacturer’s liability. No other use is permitted. For professional use only.
Air Supply Requirements
1. Supply tool with 90 PSI (6.3 KG/CM2) of clean, dry air. Higher pressure drastically
reduces toollife.
2. Connect the tool to the airline using pipe, hose, and fitting sizes shown in the diagram
below.
Lubrication
1. Use an air line lubricator with SAE #10 oil, adjustedtotwo (2) drops per minute.
If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
2. For gearing and clutch, use Shell-grade grease containingmolybdenum.
3. Grease clutches every 12,000 screws.
Torque Adjustment
Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing
which is to be tightened. The motor will start and tighten the fixing to the required
torque set by adjusting the tensions on the clutch spring. At this point, the internal drive
is disengaged and the air to the motor cut off.
1/2" (12mm)
CA048362 (1/2") NPT
CA048361 (1/2") NPT
90
0 130
1/2" (12mm)
CA048360 (1/2") NPT
1/4 NPT
3/8" (10mm)
10' (3m) MAX
Torque Cover
Air Inlet
R/L Switch
Bit Retainer Sleeve
2
1234
Operating Procedures
1. Make sure the air in airline is clean and dry.
2. Make sure the tool is connected correctly with the air compressor.
3. Install a bit (as illustrated below). Before using, do check the bit being installed in the
tool correctly.
4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring
clockwise to increase the torque. Turn the torque adjustment ring counter-clockwise
to reduce the torque. When the torque is set up, put the torque cover back and
fasten it tightly to avoid changing the set-up accidentally. (as illustrated below)
5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening
screws. Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.
6. Push to start: Push the tool to activate the motor.
7. Suggestion: Correct / Re-set torques before operation on a daily basis.
8. If not usedfor a long time, re-set the tool to the lowest torque.
Installation of Bit
Press the sleeve softly
Insert a bit
Make sure the bit
is fixed tightly
3
2
2
1
1
2
2
1
1
Set The Torque
R/L Switch
R Indication –turn right (clockwise) –fastening screw
L Indication –turn left (counter-clockwise) –loosening screw
12 3
5
4
678
12 3
5
4
678
Turn clockwise to
increase the torque
Take off the
adjustment ring
Put the torque
cover back
Fasten the rear
housing
Release the torque cover
Push Softly
Turn counter clockwise
to lower the torque
4
UT8934 AUTO SHUT-OFF STRAIGHT SCREWDRIVER - 550rpm / 1.5~10Nm
5
UT8934 AUTO SHUT-OFF STRAIGHT SCREWDRIVER - 550rpm / 1.5~10Nm
INDEX# PARTS NO.
PARTS DESCRIPTION QTY/SET INDEX# PARTS NO. PARTS DESCRIPTION
QTY/SE
T
17160001PS HOUSING CAP 141 7160041PS BLADE 5
27160061PS TORQUE COVER 142 7160040PS ROTOR 1
37160002PS C RING 143 7160042PS CYLINDER 1
47160003PS BIT RETAINER SLEEVE 144 SPP0208 SPRING PIN 1
57160004PS SPRING 145 7160045PS PIN 1
67160005PS TORQUE RING 146 7160043PS END PLATE 1
77160006PS REGULATION WASHER 147 7160046PS PIN 1
87160007PS NEEDLE PIN 348 B606ZZ BALL BEARING 1
97160008PS CLUTCH HOUSING 149 7160048PS VALVE 1
10 7160009PS ANVIL BUSHING 150 OR1898 O-RING 2
11 7160010PS WASHER 151 7160050PS END HOUSING 1
12 7160011PS TORQUE SPRING 152 7160063PS GRIP 1
13 7160013PS STEEL BALL 153 7160060PS SCREW HOLDER 1
14 7160012PS ANVIL 154 7160052PS SCREW 1
15 7160014PS STEEL BALL 255 7160051PS SWITCH 1
16 7160015PS SPRING 155 7160051PS-RD SWITCH 1
17 7160016PS SLIDE BASE 156 OR283178 O-RING 1
18 7160017PS C RING 257 7160054PS OPERATING ROD 1
19 7160018PS BALL RACE 158 OR0302 O-RING 1
20 7160019PS STEEL BALL 60 59 7160056PS VALVE PLATE 1
21 7160020PS END CLUTCH 160 7160057PS SPRING 1
22 7160021PS CENTER CLUTCH 161 7160058PS SILENCER 2
23 STB3175 STEEL BALL 262 7160059PS EXHAUST DEFLECTOR 1
24 7160023PS REAR CLUTCH 163 ZZ389507 SILENCER 1
25 7160024PS RETAINER 164 7160062PS AIR INLET 1
26 7160025PS PILOT PIN 165 CP1HP60 SUSPENSION RING 1
27 B6001Z-TPI BALL BEARING 1
28 7160027PS CENTER HOUSING 1
29 7160028PS WASHER 1
30 7160029PS GEAR CAGE 1
31 7160030PS PIN 4
32 7160031PS PLANT GEAR 4
33 7160032PS SUN GEAR 1
34 7160033PS GEAR CAGE 1
35 7160034PS PIN 4
36 7160035PS PLANT GEAR 4
37 7160036PS INTERNAL GEAR 1
38 RTW-16 C RING 1
39 L-1680HH BALL BEARING 1
40 7160039PS FRONT PLATE 1
66
7160080PS
DISTINGUISHABLE
RING(4)
1
67
7160064PS
TORQUE ADJUSTMENT
RING
1
6
Division of Florida Pneumatic Mfg Corp.,
851 Jupiter Park Lane,
Jupiter, FL 33458, USA.
Ph: (1) 561 744 9500
Fax: (1) 561 575 5574
EC/UKCA DECLARATION OF CONFORMITY
We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA
Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:
MachineType: UT8934 AirAutoShut-OffScrewdriver
TechnicalData:
ChuckSize: 1/4”HEXQC FreeSpeed: 550rpm
Weight: 0.84 kg(1.85lbs) Length: 227 mm(8.9”)
Recommended HoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)
Noise: (soundpressurelevel) 72dB(A) Vibration: 1.81Metres/Sec ²
Spindlesize: N/A Serial No: ________________
Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,
GeneralSafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO
28927,Noise:ISO15744:2008
Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development
--------------------------------------------------------------------------------
Table des matières
Autres manuels Universal Tool Tournevis électrique
Universal Tool
Universal Tool UT8226 Caractéristiques techniques
Universal Tool
Universal Tool UT8933 Manuel utilisateur
Universal Tool
Universal Tool UT8961-1 Manuel utilisateur
Universal Tool
Universal Tool UT8962-17 Manuel utilisateur
Universal Tool
Universal Tool UT8963AT-11 Manuel utilisateur
Universal Tool
Universal Tool UT8963-17 Manuel utilisateur
Universal Tool
Universal Tool UT8962-11 Manuel utilisateur
Universal Tool
Universal Tool UT8961 Caractéristiques techniques
Universal Tool
Universal Tool UT2960A Manuel
Universal Tool
Universal Tool UT8942 Manuel utilisateur
Universal Tool
Universal Tool UT2960A Manuel utilisateur
Universal Tool
Universal Tool UT8955 Caractéristiques techniques
Universal Tool
Universal Tool UT8963 Manuel utilisateur
Universal Tool
Universal Tool UT8943 Manuel utilisateur
Universal Tool
Universal Tool UT8966 Manuel utilisateur
Universal Tool
Universal Tool UT8957 Caractéristiques techniques
Universal Tool
Universal Tool UT8955 Manuel utilisateur
Universal Tool
Universal Tool UT8963AT-17 Manuel utilisateur
Universal Tool
Universal Tool UT8968 Manuel utilisateur
Universal Tool
Universal Tool UT8960-2 Manuel
