Universal Tool UT8932 Manuel utilisateur
1
INSTRUCTION MANUAL
Air Auto Shut-Off Straight Screwdrivers
This product is designed for installing and removing threadedfasteners in wood, metal,
and plastic. The use of spare parts/accessories other than those originally supplied by
the manufacturer may result in a drop in performance and/or increased
maintenance/noise level/vibrations, and as the result, the full cancellation of the
manufacturer’s liability. No other use is permitted. For professional use only.
Air Supply Requirements
1. Supply tool with 90 PSI (6.3 KG/CM2) of clean, dry air. Higher pressure drastically
reduces toollife.
2. Connect the tool to the airline using pipe, hose, and fitting sizes shown in the diagram
below.
Lubrication
1. Use an air line lubricator with SAE #10 oil, adjustedtotwo (2) drops per minute.
If an air line lubricator cannot be used, add air motor oil to the inlet once a day.
2. For gearing and clutch, use Shell-grade grease containingmolybdenum.
3. Grease clutches every 12,000 screws.
Torque Adjustment
Shut Off Clutch: Grip the tool around the handle and press the tool into the fixing
which is to be tightened. The motor will start and tighten the fixing to the required
torque set by adjusting the tensions on the clutch spring. At this point, the internal drive
is disengaged and the air to the motor cut off.
1/2" (12mm)
CA048362 (1/2") NPT
CA048361 (1/2") NPT
90
0 130
1/2" (12mm)
CA048360 (1/2") NPT
1/4 NPT
3/8" (10mm)
10' (3m) MAX
Torque Cover
Air Inlet
R/L Switch
Bit Retainer Sleeve
2
1234
Operating Procedures
1. Make sure the air in airline is clean and dry.
2. Make sure the tool is connected correctly with the air compressor.
3. Install a bit (as illustrated below). Before using, do check the bit being installed in the
tool correctly.
4. Torque Adjustment: Take off the torque cover and turn the torque adjustment ring
clockwise to increase the torque. Turn the torque adjustment ring counter-clockwise
to reduce the torque. When the torque is set up, put the torque cover back and
fasten it tightly to avoid changing the set-up accidentally. (as illustrated below)
5. Right/Left Indication: Turn right (clockwise) the switch (marked “R”) for tightening
screws. Turn left (counter-clockwise) the switch (marked “L”) for loosening screws.
6. Push to start: Push the tool to activate the motor.
7. Suggestion: Correct / Re-set torques before operation on a daily basis.
8. If not usedfor a long time, re-set the tool to the lowest torque.
Installation of Bit
Press the sleeve softly
Insert a bit
Make sure the bit
is fixed tightly
3
2
2
1
1
2
2
1
1
Set The Torque
R/L Switch
R Indication –turn right (clockwise) –fastening screw
L Indication –turn left (counter-clockwise) –loosening screw
12 3
5
4
678
12 3
5
4
678
Turn clockwise to
increase the torque
Take off the
adjustment ring
Put the torque
cover back
Fasten the rear
housing
Release the torque cover
Push Softly
Turn counter clockwise
to lower the torque
4
UT8932 AUTO SHUT-OFF STRAIGHT SCREWDRIVER 900rpm/0.5~3.0Nm
5
UT8932 AUTO SHUT-OFF STRAIGHT SCREWDRIVER 900rpm/0.5~3.0Nm
INDEX# PARTS NO.
PARTS DESCRIPTION
QTY/
SET
INDEX# PARTS NO.
PARTS DESCRIPTION
QTY/
SET
17120001PS HOUSING CAP 1 41 7120042PS CYLINDER 1
27120061PS-W TORQUE COVER 1 42 SPP0208 SPRING PIN 1
37160002PS C RING 1 43 7120045PS PIN 1
47120003PS BIT RETAINER SLEEVE 1 44 7120043PS END PLATE 1
57120004PS SPRING 2 45 7160046PS PIN 1
67120005PS TORQUE RING 1 46 R-1340HH BALL BEARING 1
77160006PS REGULATION WASHER 1 47 7120048PS VALVE 1
87140007PS PIN 3 48 OR0602 O-RING 1
97120008PS CLUTCH HOUSING 1 49 7120050PS END HOUSING 1
10 7120009PS ANVIL BUSHING 1 50 7120063PS GRIP 1
11 7120010PS WASHER 1 51 7160060PS SCREW HOLDER 1
12 7140011PS TORQUE SPRING 1 52 7160052PS SCREW 1
13 7160013PS STEEL BALL 1 53 7120051PS-RD SWITCH 1
14 7120012PS ANVIL 1 54 OR2352178 O-RING 1
15 7160014PS STEEL BALL 2 55 7120054PS OPERATING ROD 1
16 7120016PS SLIDE BASE 1 56 OR0302 O-RING 1
17 7120064PS C RING 1 57 7160056PS VALVE PLATE 1
18 7120018PS BALL RACE 1 58 7160057PS SPRING 1
19 7160019PS STEEL BALL 53 59 7160058PS SILENCER 2
20 7120020PS END CLUTCH 1 60 7120059PS EXHAUST DEFLECTOR 1
21 7120021PS CENTER CLUTCH 1 61 ZZ389507 SILENCER 1
22 STB3175 STEEL BALL 2 62 OR1898 O-RING 1
23 7120023PS REAR CLUTCH 1 63 7160062PS AIR INLET 1
24 7120024PS RETAINER 1 64 CP1HP60 SUSPENSION RING 1
25 7160017PS C RING 1
26 7120025PS PILOT PIN 1
27 B6901ZZ BALL BEARING 1
28 7120027PS CENTER HOUSING 1
29 7155029PS GEAR CAGE 1
30 7160034PS PIN 8
31 7155035PS PLANT GEAR 4
32 7155065PS SUN GEAR 1
33 7120033PS GEAR CAGE 1
34 7160035PS PLANT GEAR 4
35 7120036PS INTERNAL GEAR 1
36 RTW-16 C RING 1
37 L-1680HH BALL BEARING 1
38 7120039PS FRONT PLATE 1
39 7120041PS BLADE 5
40 7120040PS ROTOR 1
66
7160064PS
TORQUE ADJUSTMENT
RING
1
64
7160080PS
DISTINGUISHABLE RING,
4PC/SET
1
6
Division of Florida Pneumatic Mfg Corp.,
851 Jupiter Park Lane,
Jupiter, FL 33458, USA.
Ph: (1) 561 744 9500
Fax: (1) 561 575 5574
EC/UKCA DECLARATION OF CONFORMITY
We FLORIDAPNEUMATICMFGCORP,851JUPITERPARKLANE,JUPITER,FL33458,USA
Declareunderoursoleresponsibilitythatthemachinefallswithintheprovisionsofthe directive:
MachineType: UT8932 AirAutoShut-OffScrewdriver
TechnicalData:
ChuckSize: 1/4”HEXQC FreeSpeed: 900rpm
Weight: 0.52kg(1.14lbs) Length: 193 mm(7.59”)
Recommended HoseSize: 10m(3/8”) WorkingAirPressure: 6.3bar(90PSI)
Noise: (soundpressurelevel) 72dB(A) Vibration: 1.81Metres/Sec ²
Spindlesize: N/A Serial No: ________________
Towhichthisdeclarationrelates,isinconformitywiththerequirementsof:TheMachineryDirective2006/42/EC,
GeneralSafetyISO12100:2010,SpecificSafety-ImpactWrenches:ISO11148-6:2012,SpecificVibration- ISO
28927,Noise:ISO15744:2008
Nameandpositionofissuer: TonyLeNeveu:VPEngineering&Development
-
--------------------------------------------------------------------------------
Table des matières
Autres manuels Universal Tool Tournevis électrique
Universal Tool
Universal Tool UT8961-1 Manuel utilisateur
Universal Tool
Universal Tool UT8955 Manuel utilisateur
Universal Tool
Universal Tool UT8933 Manuel utilisateur
Universal Tool
Universal Tool UT8965 Manuel utilisateur
Universal Tool
Universal Tool UT8963AT-5 Manuel utilisateur
Universal Tool
Universal Tool UT8957 Caractéristiques techniques
Universal Tool
Universal Tool UT2960A Manuel utilisateur
Universal Tool
Universal Tool UT8958 Caractéristiques techniques
Universal Tool
Universal Tool UT8955 Caractéristiques techniques
Universal Tool
Universal Tool UT8943 Manuel utilisateur
Universal Tool
Universal Tool UT8966 Manuel utilisateur
Universal Tool
Universal Tool UT8961 Caractéristiques techniques
Universal Tool
Universal Tool UT8962-17 Manuel utilisateur
Universal Tool
Universal Tool UT8931 Manuel utilisateur
Universal Tool
Universal Tool UT2960A Manuel
Universal Tool
Universal Tool UT8818-S Manuel
Universal Tool
Universal Tool UT8934 Manuel utilisateur
Universal Tool
Universal Tool UT8963-17 Manuel utilisateur
Universal Tool
Universal Tool AINA PTT Caractéristiques techniques
Universal Tool
Universal Tool UT8963ATT-5 Manuel
