Universal Remote Control MX-350 Manuel utilisateur

Owner’s

Manual

OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지1

The information in this manual is copyright protected. No part of this manual may be copied or reproduced

in any form without prior written consent from Universal Remote Control, Inc. UNIVERSAL REMOTE CON-

TROL, INC. SHALL NOT BE LIABLE FOR OPERATIONAL, TECHNICAL OR EDITORIAL ERRORS/OMIS-

SIONS MADE IN THIS MANUAL. The information in this manual may be subject to change without prior

notice. MX-350 is a registered trademark of Universal Remote Control, Inc. Power of Simple is a trademark of

Universal Remote Control, Inc. All other brand or product names are trademarks or registered trademarks of

their respective companies or organizations.

500 Mamaroneck Avenue, Harrison, NY 10528

Phone: (914) 835-4484 Fax: (914) 835-4532

Thank You!

Thank you for purchasing the MX-350 Pre-Programmed and

Learning Remote Control. This manual is designed to assist you

step-by-step as you setup the MX-350 to replace all of your

remote controls and automate your home entertainment system.

Table of Contents

Getting Started 2

Button Layout 3

Basic Setup 5

Pre-Programmed Method 5

Learning Method 9

Volume Control Punch Through 12

Advanced Operation 14

Advanced Setup 16

Editing Button Labels 16

Macro Button Setup 19

Favorite Channel Setup 21

Hiding and Adding Pages 23

Erasing 25

Cloning One MX-350 to Another 26

Recalling Pre-Programmed Settings 27

Utilizing Optional RF Base Stations 28

IR/RF Signal Setting 31

ID # - Setting Base Station Address 33

EMITT - Setting IR Emitter Outputs 34

BLAST - Setting the Front Panel Blaster On or Off 35

Pre-Programmed Code Tables 37

Frequently Asked Questions 60

Warranty 61

Specifications 61

OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지2

Getting Started

Congratulations!

You’ve purchased one of the most advanced and easy to setup control sys-

tems available. The MX-350’s built-in library includes thousands of different

brands and models of remote controls. In most systems, all you have to do

to setup the MX-350 is enter which brands and models you own. If you own

a component too new to be in the library, the MX-350 uses advanced learn-

ing technology to quickly set each MX-350 button, one at at time. Setting up

your MX-350 to replace all your existing remote controls can be done in a

few minutes. Basic Setup is described on pages 5 to 13.

The MX-350’s exciting advanced features automate and customize operation

in many ways. You could use Macro Setup to power on all of your compo-

nents and start the show with the press of one button! With the MX-350’s

unique Favorite Channel capability, you can tune in a channel with the

press of one button instead of entering the entire channel number. Any of

the button names on the display can be edited as you like. It is best to

delay any Advanced Setup (described on pages 14 to 36) until after you

finish Basic Setup.

Battery Installation

Remove the battery compartment cover by pressing up the cover lock.

Insert four AAA batteries into the battery compartment as shown in the

diagram.

The MX-350

MAIN

Button

takes you

to the

MAIN

Menu.

Screen

Labeled

Display

Buttons

LIGHT

Button

PAGE

Numbers

FUNCTION

Buttons

TITLE

FAVORITE

CHANNEL

Button

PAGE

Buttons

change the

page of

Display

Buttons.

Button Layout

Universal Remote Control, Inc.

Transmitting

“Busy” Signal

Indicator*

*Note: When a command, macro or favorite channel is being transmitted, an icon will appear

in the top right corner of the display. While the MX-350 is “busy”, it will ignore a button push.

OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지2

The MX-350

Selecting a New DEVICE Changes

All Button Commands Instantly

The MX-350 can operate ten different devices even though it is only one

remote control. Let’s try it now! Press the MAIN button, then press the TV

DEVICE button.

The top of the screen changes from MAIN to TV. Now all of the buttons

change their function to operate a TV. Press the page buttons. Watch the

labels of the display buttons change with each press. There are eight pages

of display buttons already labeled for TV operation. To operate another

component (e.g., VCR, DVD etc.), press the MAIN button to return to the

MAIN menu. The MAIN menu displays five of your Devices on the

screen. Simply press one of the screen-labeled Device buttons to operate

another device. If you don’t see the device name you want, then use the

PAGE buttons to display the remaining five devices on page 2 of the

MAIN menu.

Light Button

Press the LIGHT button to backlight all the buttons. To turn off the back-

lighting, press the LIGHT button again, or just wait ten seconds (the back-

lighting automatically shuts itself off).

DEVICE

Button

MAIN

Button

LIGHT

Button

Basic Setup

You can start setting up your MX-350 using either the Pre-Programmed

Method or the Learning Method. However, all the buttons of the MX-350 are

setup at once with the Pre-Programmed Method, so it is usually faster than

the one-button-at-a-time Learning Method.

Pre-Programmed Method

Power on the A/V component you wish to setup, so that you can test

codes by sending power off commands.

Refer to the pre-programmed code tables on pages 38 - 59 and

write down the code numbers listed for your A/V component. The

code numbers are listed by categories of devices, then by brand.

See page 37 for a category list.

Press and hold both the MAIN and ENT (Enter) buttons for approxi-

mately three seconds. The top of the display will show “SETUP”.

You are in SETUP mode now.

Note: You have 30 seconds to perform a step while you are in SETUP mode. If

you don’t press a button within that time, the MX-350 will time out and return to

normal operation.

MAIN

Button ENT

Button

Universal Remote Control, Inc.

OCE-0024B_Rev05 2007.3.9 9:35 AM 페이지4

Press the P-PRO button to select the Pre-Programmed Method.

The display changes so that you can select which Device button to

setup.

In this step you choose the name of the device you’d like to setup.

Use the cursor UP or DOWN buttons to change the flashing name.

When it is correct, press the SELECT button.

For Example: I wanted to setup the TV Device button first, so I pressed the

cursor UP or DOWN until “TV” was flashing in the display.

The bottom of the display will flash “FROM TABLE”.

In this step you verify the type of component you plan to operate

with this device button. If the flashing name is correct, press

SELECT.

If the name flashing in the display is incorrect (for example, you are setting up

AUX to operate a Laser Disc Player), use the UP and DOWN buttons to

change the flashing name to the correct type of component.

Note: Each name that appears in the display may include several types of

components. For example, the DVD category includes DVD players and

Laser Disc Players. See page 37 for a list of component types each Code

Table contains.

Point the MX-350 at the component, then enter the first three digit

code number from your notes using the numbered buttons. After

you enter each three digit number, look at the component to see if

it turned off.

Continue to enter code numbers until the component powers off.

For Example: I have a Sony TV. I found the code numbers 070, 139,147,

126, 185, 194 and 085 under Sony in the TV TABLE. Using the numbered

buttons on the MX-350, I entered 070 and looked at the TV. It didn’t turn off,

so I entered 139, then 147 and so on, until I found the code that powered

off the TV.

P-PRO

Button

The MX-350

SELECT

DOWN

Press a Page button to display the

other five Device names.

First

Five

Device

Names

SELECT

Use the

number

buttons to

enter the

code

number.

Universal Remote Control, Inc.

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지6

Note: If a component fails to turn off after you have entered all of the code

numbers listed for your brand, you can scan through the other brands in the

table using the UP and DOWN buttons (there is a chance that your

component was actually manufactured by another brand). However, most of

the code tables are so large it is usually faster to use the Learning Method on

Page 9.

When the component turns off, save the code number you entered

by pressing the SAVE button that appears on the screen.

Exit SETUP mode by pressing the MAIN button two times. When

the display shows “MAIN”, you are back in normal operating

mode.

Repeat steps one through nine for each of your devices. If you are

missing any commands, use the learning method, described next

Learning Method

The MX-350 can learn commands from your old remote controls one-but-

ton-at-a-time by following these simple steps:

Line-up the MX-350 with your old remote control, head-to-head,

one or two inches apart.

On the MX-350, press and hold the MAIN and ENT (Enter) buttons at

the same time for approximately three seconds. The top of the dis-

play will show “SETUP”. You are in SETUP mode now.

Note: You have 30 seconds to perform a step while you are in SETUP mode. If

you don’t press a button within that time, the MX-350 will time out and return to

normal operation.

Press the LEARN button.

The top of the screen will change to “LEARN”.

SAVE

Button

Code

Number

You

Entered

MAIN

Button

The MX-350

Scan Up to the next Code

Number

Scan Down to the previous

Code Number

Press Power On or Power

Off to test if the device

powers off.

Universal Remote Control, Inc.

LEARN

Button

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지8

The display will show a list of the first five devices.

Select the device you would like to teach commands to by pressing

the Device button.

Now, press any button you want to teach a command to.

Note: If you don’t see the display button you would like to teach, use the

PAGE buttons. The only buttons you can’t teach are the PAGE and MAIN but-

tons.

Once you press a button, the top of the display will change from

“LEARN” to “READY”.

1110

Press and hold the button you want on your old remote control until

the display changes to either “GOOD” or “FAILED”.

If the “GOOD” label appears on top of the display, you were successful.

Now, press the next button you wish to teach. Keep repeating steps 6

through 7 until you have learned all the buttons you want.

If the “FAILED” label appears on top of the display, try to teach the

same button in MX-350 once again by repeating steps 6-7.

Continue to teach any commands from any of your remote controls

by repeating steps 5-7 (to go back to step five, press MAIN once).

Once you completed teaching all the buttons, return to normal opera-

tion by pressing the MAIN button twice. Test all your new commands.

If any of them don’t work, try learning again using these notes:

The MX-350

Press any

of the

Device

Buttons.

Press

any

Button.

Move to another room. Plasma TVs, sunlight, halogen or

quartz lighting can interfere with the learning process.

Although the old remote control seems to work fine,

change the batteries to fresh alkaline batteries.

Vary the distance between the remote controls

gradually. Try 1/4”, 1”, 2”and so on, up to 4 feet.

Tap the button on the original remote control instead of

pressing and holding it during the learning process.

Universal Remote Control, Inc.

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지10

Volume Control Punch Through

In most home entertainment systems, the sound volume is only con-

trolled by one device. In some systems, it is the TV speakers that make

the sound, so you would use the TV device on the MX-350 to raise and

lower the volume. In another system, it might be a surround sound

receiver and speakers that control the sound, so you would use the

MX-350’s AUDIO device to adjust the volume. Constantly switching the

MX-350 to TV or AUDIO to adjust the volume is inconvenient in daily

life.

You can use Punch Through to set the MX-350’s volume buttons to always

control the sound in your system. That way when the MX-350 is set to

VCR or DVD, the volume up, down and mute buttons will work perfect-

ly without switching back to AUDIO or TV. Here’s how:

Enter Setup mode by pressing and holding both MAIN and ENT for

three seconds. The top of the display show you are in SETUP mode

now.

Note: You have 30 seconds for each step, otherwise the MX-350 will time

out automatically.

Press the PAGE UP button to get to page 2 of the SETUP menu.

Press the PUNCH button.

Press the VOL button. The display confirms by displaying “VOL” at the

top of the screen. This sets up the group of three buttons (Volume Up,

Volume Down and Mute) in one action!

The bottom of the display flashes ”PUNCH TO”.

Press the device button for the device that doesn’t have volume

control commands yet (i.e.,DVD). This is the device you are going

to PUNCH TO for the volume and mute commands.

Note: If you wish to PUNCH to the MAIN device, press the POWER OFF

button at this time.

The bottom of the display will then flash “PUNCH FROM”. Now

you select the device that has the volume commands you want

(i.e.,TV for systems using the TV speakers, AUDIO for systems with

surround sound receivers). The bottom of the

display will flash “SAVED”.

Repeat steps 3-5 until all your devices operate the volume perfect-

ly. Press the MAIN button twice to return to normal operating

mode and test your Punch Through settings.

Note: The Punch Through feature is not limited to

volume and can also be applied to channel or other functions. If you find

yourself switching to a particular device frequently to use a group of con-

trols, consider using Punch Through for another group, as listed here:

VOL - Volume Up, Volume Down and Mute

CH -

Channel Up, Channel Down, Prev. Channel and Number buttons (0-9, +10, ENT)

PLAY - Play, Stop, Pause, Rewind and Fast Forward

VOD - Guide, Menu, Info, Exit, Up, Down, Left, Right, Sel

POWER - Power On and Power Off

The MX-350

Select

Volume

Universal Remote Control, Inc.

Select

the Device

you want to

“Punch To”

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지12

Adjusting Contrast

You can make the text darker by pressing both the MAIN and cursor UP

buttons at the same time. To make the text appear lighter, press both the

MAIN and cursor DOWN buttons at the same time.

Transmitting (Busy Signal) Icon

When a command is being transmitted, an icon will appear in

the top right corner of the display. It is a useful aid when setting

up Macros and FAVs, since it flashes with every step of a

sequence of commands.

Advanced Operation

Setting Backlight Options

You can adjust the amount of time that the MX-350 backlight stays on by

entering the SETUP mode and proceeding to page two (using the PAGE

UP button), then pressing the LIGHT button on the display (not the

Backlight button). Then enter the amount of time you would like the

light to stay on using the number pad (0-99 seconds). After making your

selection, press the SAVE button.

If you don’t want backlighting at all (this extends battery life), press the ON

button that appears on the screen. The ON will change to OFF. Press the

SAVE button. Exit the setup mode by pressing the MAIN button.

The FAV Button

When you press the FAV button, the display changes to a list of your

favorite TV channels. Each button can be set to instantly select the channel

on your TV. There are eight pages of five favorite channel buttons for a total

of 40. Simply touch the PAGE buttons to display the other favorite chan-

nels. To return to the last device you viewed, press MAIN once (a second

press will take you to the MAIN menu).

To setup your Favorite Channel buttons go to page 21.

The MX-350

Favorite

Channel

Buttons

FAV

Button

Contrast set low.

Cursor

Up & Down

Buttons

MAIN

Button

Contrast set high.

Universal Remote Control, Inc.

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지14

Press the button you wish to edit. The first character of your button

label blinks.

Advanced Setup

After you’ve finished all your basic setup, you can choose to make opera-

tion easier by customizing the MX-350 just the way you want, using the

Advanced Setup features described in this section.

Editing Button Labels

You can change the name of any of the display buttons (including

Favorite Channels) by following these steps:

Press and hold both the MAIN and ENT (Enter) buttons for approx-

imately three seconds. The top of the display will show “SETUP”.

You are in SETUP mode now.

Note: You have 30 seconds to perform a step while you are in SETUP mode. If you don’t

press a button within that time, the MX-350 will time out and return to normal operation.

Press the EDIT button.

The display changes to the EDIT menu. Press the TEXT button.

The screen displays the list of devices and “EDIT” will appear at

the top of the screen. Navigate to the device and page where there

is a button label you want to EDIT, selecting between the FAV,

MAIN, DEVICE, then using the PAGE button.

The MX-350

TEXT

Button

EDIT

Button

Blinking

Character

EDIT flashes at the bottom of the screen.

Universal Remote Control, Inc.

A,B,C,1 D,E,F,2 G,H,I,3

J,K,L,4 M,N,O,5 P,Q,R,6

S,T,U,7 V,W,X,8 Y,Z,9

DOWN Cursor

button deletes the currently

blinking character.

UP Cursor

button deletes ALL text.

LEFT Cursor

button

moves blinking

character left.

RIGHT Cursor

button

moves blinking

character right.

Change the character by

using any of the number

keys. Each press of the

same number button selects

the next character of that

number’s group, as shown

here.

Once the character you

want appears, move to the

next space by pressing the

RIGHT cursor button.

OCE-0024B_Rev05 2007.3.9 9:36 AM 페이지16

Table des matières

Autres manuels Universal Remote Control Télécommande universelle

Universal Remote Control

Universal Remote Control total control TRC-780 Manuel utilisateur

Universal Remote Control

Universal Remote Control CLIKR-5 UR5L-6200L Manuel utilisateur

Universal Remote Control

Universal Remote Control BW-1220US Manuel utilisateur

Universal Remote Control

Universal Remote Control Unifier URC-100 Manuel utilisateur

Universal Remote Control

Universal Remote Control PHAZR -5 UR5U-9000L Manuel utilisateur

Universal Remote Control

Universal Remote Control UR4-DSR Manuel utilisateur

Universal Remote Control

Universal Remote Control OCE-0085A Manuel utilisateur

Universal Remote Control

Universal Remote Control Complete Control MX-880 Manuel utilisateur

Universal Remote Control

Universal Remote Control UR17E - CODE BOOK Manuel utilisateur

Universal Remote Control

Universal Remote Control POWERBLASTER MRF100B Manuel utilisateur

Universal Remote Control

Universal Remote Control UR-S86TVE Manuel utilisateur

Universal Remote Control

Universal Remote Control COMPLETE CONTROL MX-450 Manuel utilisateur

Universal Remote Control

Universal Remote Control Easy Clicker UR2-211 Manuel utilisateur

Universal Remote Control

Universal Remote Control CLIKR-5 UR5L-8700L Manuel utilisateur

Universal Remote Control

Universal Remote Control COMPLETE CONTROL MX-880Z Manuel utilisateur

Universal Remote Control

Universal Remote Control MRF-300/RFX150 Manuel utilisateur

Universal Remote Control

Universal Remote Control UR4-DSR Manuel utilisateur

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-8500 Manuel utilisateur

Universal Remote Control

Universal Remote Control UR2-DTA Manuel utilisateur

Universal Remote Control

Universal Remote Control CABLEVISION OCE-0027A Manuel utilisateur

Universal Remote Control

Universal Remote Control Customizer URC-300 Manuel utilisateur

Universal Remote Control

Universal Remote Control Complete Control MX-810 Manuel utilisateur

Universal Remote Control

Universal Remote Control CLIKR-5 UR5U-6200L Manuel utilisateur

Universal Remote Control

Universal Remote Control Complete Control MX-780 Manuel utilisateur

Manuels Télécommande universelle populaires d'autres marques

Pronto

Pronto Peel Manuel utilisateur

GE 24929 Manuel utilisateur

Radio Shack

Radio Shack Wireless Remote Control System Manuel utilisateur

AUVIO

AUVIO Universal Home Theater Remote Manuel utilisateur

Philips

Philips Icon SRU4106 Manuel utilisateur

THOMSON

THOMSON ROC4309 Manuel utilisateur

Philips

Philips pm625S Manuel utilisateur

GE RM94931 Manuel utilisateur

RCA

RCA RCU600WMS - Universal Remote Control Manuel utilisateur

Blackweb

Blackweb BWB17AV002 Manuel utilisateur

Marmitek

Marmitek DoorGuard 300 Manuel utilisateur

Chunghop

Chunghop RM-L618 Manuel utilisateur

GE RM24965 Manuel utilisateur

Anderic

Anderic KTN828 Manuel utilisateur

Sunwave Tech.

Sunwave Tech. Touch Screen Remote Control Manuel utilisateur

Medion

Medion E74023 Manuel utilisateur

intensity

intensity RM02A Manuel utilisateur

GE RM24950 Manuel utilisateur