Unitek Classic P3 Series Manuel utilisateur
Manual
Classic P3
1 Quadrant
Thyristor Drive
Part 1 Thyristor Drive P3x/x-240...840A
Part 2 Analogue Control Electronics REG4
P3 240-840
Edition
0910
Classic P3 x/x - 240-840A
2
Contents Page
1. Basic Information
Safety advice 3
Standards and guidelines 3
General information 4
Features 5
Technical da 6, 7
Specification 8
2. Mechanical installation 9
Dimensions 10, 11
3. Electrical installation
Connections 12
Connection diagram 13
CE advice 14
Power supply 15, 16
Option - synchronization 17
Motor connection 19
Field connections 20
Actual value connection 21
Components 22
Adjustments 22
Circuit diagram 23
Current control loop 24
Signals 25
Measurements 25
4. Commissioning + REG4 26, 27
5. Faults 28, 29
6. Guarantee 30
7. Protocol 31, 32
8. Drawings
Dimensions (P3 240-360A) 33
Dimensions (P3 480-840A) 34
Note: For the commissioning and the error diagnosis please
refer to the manuals Q..., P...!
Observe any cross-references!
Contents
1 Basic - Information
P3 240-840A 3
Electronic equipment is not fault proof. This fact should be borne in mind for all
possible operating conditions.
Before installation or commissioning begins, this manual must be thoroughly read
and understood by the technical staff involved.
If any uncertainty arises, the manufacturer or dealer should be contacted.
P3 devices are power electric parts used for regulating energy flow.
Protection rating IP00.
Standards and guidelines
The device and its associated components can only be installed and switched on
where the local regulations and technical standards have been strictly adhered to:
EU Guidelines 89/392/EWG, 84/528/EWG, 86/663/EWG, 72/23/EWG
EN60204, EN50178, EN60439-1, EN60146, EN61800-3
IEC/UL IEC364, IEC 664, UL508C, UL840
VDE Regulations VDE100, VDE110, VDE160
TÜV Regulations
Trade body guidelines VGB4
The user must ensure that in the event of:
- device failure
- incorrect operation
- loss of regulation or control
the axis will be safely de-activated.
It must also be ensured that the machine or equipment are fitted with device
independent monitoring and safety features.
Setting adjustments
- should only be carried out by suitably trained personnel
- should only be carried out in accordance with health and safety guidelines
Assembly
- should only be carried out when all voltages have been removed.
QS
Test results are archived with the device serial number by the manufacturer.
CE
The device adheres to the following: Guideline EU 89/336/EWG. EMC standards
EN61000-2 and EN61000-4.
Safety advice - Standards and guidelines
ATTENTION - High voltage
500V
~
ac, 650V=dc
Classic P3 x/x - 240-840A
4
Attention
This manual P3 only describes the basic control unit.
P3
This device description must be read in conjunction with the
manual for
- an analogue control REG xx
- an internal field control Q3-F
- an external field control F2
- options Multi
General information
Series Classic P3
General information
1 Basic - Information
P3 240-840A 5
Build
- switch cabinet mounting
- according to the VDE, DIN and EU regulations
- standard control electronics REG
-intrinsically safe power section with current control loop
- controlled or uncontrolled field supply unit
- optional units
Galvanic isolation between
- the power section and the housing
- the power section and the control electronics
The distance of air gaps and leakage paths adhere to the VDE standards (>8mm).
Components
- fully insulated thyristor modules, comfortably over-dimensioned
- only components customary in trade and industrially standardised are used
- high-quality bases for the IC with external connections
- LED displays
- precision potentiometers for fine adjustments
- plug-in jumpers for the system set-up
Characteristics
* Series Klassik P3
* Thyristor drive for dc motors
* Power range 108kW to 378kW
* Drive in 1 quadrant
* Energy recovery
* Intrinsically safe power section
* Fast analogue current control
* Temperature watchdog - power section
* Controlled or uncontrolled field rectifier
* 26-pin interface
* Features of the control electronics:
see Manual REGxx or third-party product documentation
* Optional units
Features
Classic P3 x/x - 240-840A
6
P3 400/450-x
Power connection
Auxiliary voltage connection
Output voltage
Cooling
360 ... 440V~
360 ... 440V~ or 200...250V~
max. +450V=
ventilation fan
P3 400/450- 240 360
Input current A~ 192 288
Output current peak 5 s.
continuous
A=
A=
480
240
720
360
El. power kW 108 162
Fuses - input 3 pcs.
- field
ff installed installed
AFF 250 315
AF 10 10
Power chokes Type
mH
1x KD5-250
0.12
3x K 170-400
0.08
Armature chokes
Armature choeks are necessary only for special
applications.
Type
mH
Ul180B250
2.2
Ul210C400
1.8
Dimensions w
x
h
x
d mm 305x510x240 305x510x240
Wieght kg 23 23
P3 500/550-x
Power connection
Auxiliary voltage
Output voltage connection
Cooling
450 ... 550V~
360 ... 440V~ or 200 ... 250V~
max. +550V=
ventilation fan
P3 500/550- 240 360
Input current A~ 192 288
Output current - peak
- continuous
A=
A=
480
240
720
360
El. power kW 132 198
Fuses - input 3pcs.
- field
ff installed installed
AFF 250 315
AF 10 10
Power chokes Type
mH
1x KD5-250
0.12
3x K 170-400
0.08
Armature chokes
Armature chokes are necessary only for special
applications.
Type
mH
Ul180B250
2.2
Ul210C400
1.8
Dimensions w
x
h
x
d mm 305x510x240 305x510x240
Weight kg 23 23
Technisccal data
1 Basic - Information
P3 240-840A 7
P3 400/450-x
Power connection'
Auxiliary volrtage connection
Output connection
cooling
360 ... 440V~
360 ... 440V~ or 200...250V~
max. +450V=
ventilation fan
Gerät P3 400/450- 480 840
Input current A~ 384 672
Output current - peak
- continuous
A=
A=
960
480
1680
840
El. power kW 216 378
Fuses - input 3 pcs.
- field
ff installed installed
AFF 400 500
AF 10 10
Power chokes Typ
mH
3x KU150-600
0.06
3x KU150-800
0.04
Armature chokes
Armature chokes are necessary only for special
applications.
Typ
mH
Ul240C500
1.6
Ul240-700
1.2
Dimensions w
x
h
x
d mm 405x560x240 486.5x560x240
Weight kg 36 40.8
P3 500/550-x
Power connections
Auxiliary voltage connections
Output voltage
Cooling
450 ... 550V~
360 ... 440V~ or 200...250V~
max. +550V=
ventilation fan
P3 500/550- 480 840
Input current A~ 384 672
Output current - peak
- continuous
A=
A=
960
480
1680
840
El. power kW 264 462
Fuses - input 3pcs.
- field
ff installed installed
AFF 400 500
AF 10 10
Power chokes Type
mH
3x KU150-600
0.06
3x KU150-800
0.04
Armature chokes
armature chokes are necessary only for special
applications.
Type
mH
Ul240C500
1.6
Ul240-700
1.2
Dimensions w
x
h
x
d mm 405x560x240 486.5x560x240
Weight kg 36 40.8
Technical data
Classic P3 x/x - 240-840A
8
Specification
Mains frequency 50 or 60Hz ±5%
Protection rating IP 00
Format VDE 0100 group C,
VDE 0160
Humidity rating class F acc. to DIN 40040
Site of installation < 1000m above sea level
Operating temperature range 0 ... 45°C
Extended operating temp. Range up to 60°C reduced by 2%/°C
Storage temperature range -30°C to + 80°C
Current control loop circuit
Amplification
- input signal 0 to ±10V=
- output 0 to ±200% type current
Over-current limiting 10s 200% type current
Control precision ±2%
Control range 1:50
Enable >+10V
Speed control loop circuit (with manual REG)
Control precision
(without actual value error) <±0.1%
Control range >1:1000
Interface control electronics X3
Function Connector no.
+ 24V ±10% X3: 1 and 2
+ 15V ±2% X3: 3 and 4
- 24V ±10% X3: 5 and 6
- 15V ±2% X3: 7 and 8
Device GND 0 X3: 9, 10, 11, 12, 13, 14
I command value (GND) 0 X3: 15
I command value (signal) +10V= X3: 16
Current controller enable +10V= X3: 17
Drive disable1 +10V= X3: 18
Drive disable 2 +10V= X3: 19
N (speed) actual +10V= X3: 20
I (current) actual +5V= X3: 21
Over-current power section +10V= X3: 22
Option U
A
±10V= X3: 23
Option U
A
0-10V= X3: 24
Drive ready BTB +10V= X3: 25
+5V X3: 26
Technical data
2 Mechanical Installation
P3 240-840A 9
Mounting
Air flow direction
Ambient temperature 0 bis <45°C (reduced, up to 60°C)
max. Cooling unit temperature 80°C (internal watchdog)
Air-mass throughput 240A 680m³h
360A 680m³h
480A 820m³h
840A 820m³h
Dissipation loss with max. power
Unit P3-x/x- Unit W Mains choke W
240A- 1000 260
360A- 1440 330
480A- 1890 400
840A- 3060 780
Classsic P3 x/x - 240-840A
10
RVI1
RVI2
Enable
Phase
BTB
Field current
S2
S1
min. field current
triggering point
max. field current
Dimensions
Three-phase power choke single -phase mains choke
up to 250A from 360A
Features
U
N
400V~50/60Hz
U
K
4%
Protection rating
IP00
isol. Class T40/E
vertical angle bracket
Unit
P3-Type Choke L
mH
PV
W
Dimensions
a b c d e
Weight
kg
Screw
M
240A KD5-250 0.12 260 300 170 270 200 100 31.5 8
360A K170-400 0.08 330 142 170 230 106 88 14 8
480A KU150-60
00.06 400 210 260 275 100 108 29 8
660A KU150-60
00.06 610 210 260 275 100 108 29 8
840A KU150-80
00.04 780 210 270 275 100 108 31 8
with filter: KDF xx
P3 240/360A
Autres manuels pour Classic P3 Series
1
Ce manuel convient aux modèles suivants
8
Table des matières
Autres manuels Unitek Entraînement CC
Unitek
Unitek Classic Q3 15-150A 4 Quadrant Manuel utilisateur
Unitek
Unitek Classic Q6 Manuel utilisateur
Unitek
Unitek Classic Q3x/x-240-840A Series Manuel utilisateur
Unitek
Unitek TVD6.2-RS Manuel utilisateur
Unitek
Unitek Classic P3 Series Manuel utilisateur
Unitek
Unitek Bamobil D3.2 Manuel utilisateur
Unitek
Unitek Classic Q3 Series Manuel utilisateur
Manuels Entraînement CC populaires d'autres marques
Vincent Associates
Vincent Associates UNIBLITZ ED12DSS Manuel utilisateur
EKSMA OPTICS
EKSMA OPTICS DQ-100-4 Manuel de la liste des pièces
Chamberlain Garog
Chamberlain Garog D Series Manuel utilisateur
Parker
Parker PDS Series Manuel utilisateur
Festo
Festo DGC G Series Guide de configuration
Binks
Binks QS-5012-1-CE Manuel utilisateur
