Unit UT513A Manuel utilisateur

It is recommended to select the specific 8pcs

When charging battery is applied, the charging battery

work mode should be selected at the startup:

UT513A

Insulation Resistance Tester

1 pc

8 pcs

One-plug

Two-plug

optional,

chargeable batteries (LR14) and a charger.

damaged part,

measurement requirement: Pollution Degree 2,

Overvoltage Category(CAT. III 600V) and Double

Insulation.

alerts the user to avoid electric shock.

affect

test

leads and power adaptor with the same

model or identical electrical specifications.

Low Battery Indication

after 15 minutes' inactivity.

There is a battery indicator shown on the upper left

corner of the display. Please refer to Table 3 for

detailed explanation.

almost

necessary. Under this status, the Meter

can still output 500V and 1000V to

measure, the measured accuracy will

not be affected.

hold USB button prior to startup, then press down ON/

OFF, LCD screen will display CHA or GEN, and select

to display CHA by pressing the up/down key, after

pressing USB key to confirm, the Meter successfully

enters the charging battery work mode. GEN means

the general alkaline battery work mode.

Press and

Two-plug

One-plug

(Connected to one-plug test lead)

(Connected to one-plug black test lead)

( Connected to two-plug red test lead )

(Connected to two-plug red test lead)

voltage input terminal

Arrow Button

The Meter defaults at 500V range and

under continuous measurement of

insulation resistance when turned on.

LIGHT Press to turn on/off the backlight.

Press to clear the saved data.

value. The Meter can save up to 18 sets.

voltage range.

next voltage

range.

setting the timer for the

When compare function is enabled for

insulation resistance measurement,

values

setting the timer for the

When compare function is enabled for

insulation resistance measurement,

values

Press

measurements

This

The Meter defaults at

500V range and under continuous measurement of

insulation resistance when turned on.

P/N:110401104385X

This operating manual is subject to change without notice.

*END*

UT513A

Insert the red test lead into two LINE terminals,

the black one into GUARD and the green one

into EARTH.

-114

Caution

test leads into EARTH

and two LINE terminals.

present on the red test lead,

if negative voltage is

output

cause

measuring resistance ＜2MΩ with use of 500V.

measuring resistance ＜5MΩ with use of 1000V.

measuring resistance ＜10MΩ with use of 2500V.

measuring resistance ＜20MΩ with use of 5000V.

voltage range.

green

outputs

Choose one of insulation resistance measurement

modes shown as below:

personal injury.

carry out begin and output insulation resistance

test voltage

turn off the voltage output,

the

the test voltage

output will be turned off,

the test

voltage output will be turned off and the

step

readings.

Calculation Tips:

PI = 3-minute ~ 10-minute resistance/30-second ~

1-minute resistance

You can choose compare from:

compare value.

See Figure 6 for the use of power adaptor.

Using Power Adaptor

Figure 6. Using Power Adaptor

Connecting USB Interface

See Figure 7 for USB interface connection.

General Specifications

18 sets

Test Voltage Automatically source the voltage.

Preset the timer for

two points and the Meter will carry out the measurement automatically.

B. Insulation Resistance Measurement

less

Autres manuels Unit Équipement de test

Unit

Unit UT276A Manuel utilisateur

Unit

Unit UTD2000CEX-II Series Manuel utilisateur

Unit

Unit UPO1000X Series Manuel utilisateur

Unit

Unit UPO1000CS Series Manuel utilisateur

Unit

Unit UT 4000 Series Manuel utilisateur

Unit

Unit utd2000 Manuel utilisateur

Unit

Unit UTD4000 Series Manuel utilisateur

Unit

Unit UT5583 Manuel utilisateur

Unit

Unit UT-513A Manuel utilisateur

Unit

Unit UTD2000CEX+ Series Manuel utilisateur

Unit

Unit UTD1025CL Manuel utilisateur

Unit

Unit UT502A Manuel utilisateur

Unit

Unit UPO3000E Series Manuel du propriétaire

Unit

Unit UT521 Manuel utilisateur

Unit

Unit UT3200+ Series Manuel utilisateur

Unit

Unit UT590 Series Manuel utilisateur

Unit

Unit UT673A Manuel utilisateur

Unit

Unit UT3550 Manuel utilisateur

Unit

Unit UT501A Manuel utilisateur

Unit

Unit UTD2025 series Manuel utilisateur

Unit

Unit UPO2000CS Series Manuel utilisateur

Unit

Unit UT677A Manuel utilisateur

Unit

Unit UT890D Manuel utilisateur

Unit

Unit UT522 Manuel utilisateur

Manuels Équipement de test populaires d'autres marques

SMART

SMART KANAAD SBT XTREME 3G Series Manuel utilisateur

Agilent Technologies

Agilent Technologies BERT Serial Manuel utilisateur

Agilent Technologies

Agilent Technologies N3280A Manuel utilisateur

Vernier

Vernier Go Direct Voltage Manuel utilisateur

Lifeloc

Lifeloc R.A.D.A.R. Manuel utilisateur

Fluke

Fluke T5-600 Instructions d'utilisation et d'installation

Mercury

Mercury TSL01 Manuel utilisateur

MAHA

MAHA MBT Series Manuel utilisateur

Fuji Electric

Fuji Electric P-61 Manuel utilisateur

ETC

ETC SealerAtor Manuel utilisateur

Skyfine

Skyfine ETHYWAY V2 Manuel utilisateur

Appion

Appion G5 Twin Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuel utilisateur

BW Technologies

BW Technologies MicroDock II Manuel utilisateur

Sun Nuclear

Sun Nuclear 1027 Manuel utilisateur

Biomark

Biomark HPR LITE READER Manuel utilisateur

Hioki

Hioki 3169-20 Manuel utilisateur

Ashcroft

Ashcroft ATE-100 Manuel utilisateur