Unit UT90B Manuel utilisateur
Table of Contents
Title Page
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
Rotary Switch
Functional Buttons
Display Symbols
Measurement Operation
A. DC & AC Voltage Measurement
B. AC & DC Current Measurement
C. Test for Diodes & Continuity
D. Resistance Measurement
E. Power Charging
The Impedance Changeover Button
The POWER Button
General Specifications
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. AC Current
D. DC Current
E. Diodes & Continuity Test
F. Resistance
Maintenance
A. General Service
B. Replacing the Fuses
3
4
5
6
8
9
10
11
12
14
14
15
17
20
22
23
23
24
26
26
26
27
27
28
28
29
29
29
Model UT90B: OPERATING MANUAL
1
Table of Contents
Title Page
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
Rotary Switch
Functional Buttons
Display Symbols
Measurement Operation
A. DC & AC Voltage Measurement
B. AC & DC Current Measurement
C. Test for Diodes & Continuity
D. Resistance Measurement
E. Power Charging
The Impedance Changeover Button
The POWER Button
General Specifications
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. AC Current
D. DC Current
E. Diodes & Continuity Test
F. Resistance
Maintenance
A. General Service
B. Replacing the Fuses
Model UT90B: OPERATING MANUAL
2
Overview
This Operating Manual covers information on safety and
cautions. Please read the relevant information carefully
and observe all the Warnings and Notes strictly.
Warning
To avoid electric shock or personal injury, read the
"Safety Information" and "Rules for Safe Operation"
carefully before using the Meter.
The Model UT90B (hereafter referred to as “the Meter”)
is a 1999 counts 3 1/2 digits multimeter with stabilized
functions, safe design, and reliable performance.
In addition to the conventional measuring function, such
as DC/AC voltage, DC/AC current, resistance, diode and
continuity, it is equipped with advanced design of charging
power through 220VAC or 12-36VAC/DC or solar energy.
With such design, the Meter can be used without battery,
therefore it will not cause chemical pollution. This is also
a highly applied digital electrical tester of good
performance with full icons display LCD, overload
protection and streamline outlook.
Table of Contents
Title Page
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
Rotary Switch
Functional Buttons
Display Symbols
Measurement Operation
A. DC & AC Voltage Measurement
B. AC & DC Current Measurement
C. Test for Diodes & Continuity
D. Resistance Measurement
E. Power Charging
The Impedance Changeover Button
The POWER Button
General Specifications
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. AC Current
D. DC Current
E. Diodes & Continuity Test
F. Resistance
Maintenance
A. General Service
B. Replacing the Fuses
Model UT90B: OPERATING MANUAL
3
Unpacking Inspection
Open the package case and take out the Meter. Check
the following items carefully to see any missing or
damaged part:
In the event you find any missing or damage, please
contact your dealer immediately.
Table of Contents
Title Page
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
Rotary Switch
Functional Buttons
Display Symbols
Measurement Operation
A. DC & AC Voltage Measurement
B. AC & DC Current Measurement
C. Test for Diodes & Continuity
D. Resistance Measurement
E. Power Charging
The Impedance Changeover Button
The POWER Button
General Specifications
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. AC Current
D. DC Current
E. Diodes & Continuity Test
F. Resistance
Maintenance
A. General Service
B. Replacing the Fuses
Model UT90B: OPERATING MANUAL
4
Item
1
2
3
Description
English Operating Manual
Test Lead
Holster
Qty
1 piece
1 pair
1 piece
Safety Information
This Meter complies with standards IEC61010: in pollution
degree 2, overvoltage category (CAT. II 1000V, CAT. III
600V) and double insulation.
Use the Meter only as specified in this operating manual,
otherwise the protection provided by the Meter may be
impaired.
In this manual, a Warning identifies conditions and
actions that pose hazards to the user, or may damage
the Meter or the equipment under test.
A Note identifies the information that user should pay
attention on.
International electrical symbols used on the Meter and
in this Operating Manual are explained on page 8.
Model UT90B: OPERATING MANUAL
5
Rules For Safe Operation (1)
Warning
To avoid possible electric shock or personal injury,
and to avoid possible damage to the Meter or to the
equipment under test, adhere to the following rules:
l Before using the Meter inspect the case. Do
not use the Meter if it is damaged or the case (or
part of the case) is removed. Look for cracks or
missing plastic. Pay attention to the insulation
around the connectors.
l Inspect the test leads for damaged insulation
or exposed metal. Check the test leads for
continuity. Replace damaged test leads with
identical model number or electrical specifications
before using the Meter.
l When using the test leads, keep your fingers
behind the finger guards.
l Do not apply more than the rated voltage, as
marked on the Meter, between the terminals or
between any terminal and grounding.
l When the Meter working at an effective voltage
over 60V in DC or 30V in AC, special care should
be taken for there is danger of electric shock.
l Use the proper terminals, function, and range
for your measurements.
l The rotary switch should be placed in the right
position and no any changeover of range shall
be made during measurement is conducted to
prevent damage of the Meter.
l Disconnect circuit power and discharge all high-
voltage capacitors before testing current,
resistance, diodes or continuity.
l Replace the battery as soon as the battery
indicator appears. With a low battery, the Meter
might produce false readings that can lead to
electric shock and personal injury.
Model UT90B: OPERATING MANUAL
6
Rules For Safe Operation (2)
l When servicing the Meter, use only the same
model number or identical electrical specifications
replacement parts.
l The internal circuit of the Meter shall not be
altered at will to avoid damage of the Meter and
any accident.
l Soft cloth and mild detergent should be used
to clean the surface of the Meter when servicing.
No abrasive and solvent should be used to
prevent the surface of the Meter from corrosion,
damage and accident.
l Turn off the Meter when it is not in use.
l Do not use or store the Meter in an environment
of high temperature, humidity, explosive,
inflammable and strong magnetic field. The
performance of the Meter may deteriorate after
dampened.
l The Meter is suitable for indoor use.
Model UT90B: OPERATING MANUAL
7
International Electrical Symbols
AC (Alternating Current).
DC (Direct Current).
Grounding.
Double Insulated.
Deficiency of Power.
Fuse
Warning. Refer to the Operating Manual.
Conforms to Standards of European Union.
Model UT90B: OPERATING MANUAL
8
The Meter Structure (see figure 1)
9
( figure 1)
1 LCD Display.
2 Solar Panel.
3 Impedance Changeover Button.
4 Rotary Switch.
5 Input Terminals.
6 Power Button.
Model UT90B: OPERATING MANUAL
10
Rotary Switch
Below table indicated for information about the rotary
switch positions.
µ
µ
Model UT90B: OPERATING MANUAL
Table des matières
Autres manuels Unit Multimètre
Unit
Unit UT801 Manuel utilisateur
Unit
Unit UT39A Manuel utilisateur
Unit
Unit UT513 Manuel utilisateur
Unit
Unit UT71A Manuel utilisateur
Unit
Unit UT30B Manuel utilisateur
Unit
Unit UT695D Series Manuel utilisateur
Unit
Unit UT90C Manuel utilisateur
Unit
Unit UT107 Manuel utilisateur
Unit
Unit UT39B Manuel utilisateur
Unit
Unit UT203 Manuel utilisateur
Unit
Unit MIE0146 Manuel utilisateur
Unit
Unit UT232 Manuel utilisateur
Unit
Unit UT60A Manuel utilisateur
Unit
Unit UT 61+ Series Manuel utilisateur
Unit
Unit UT204A Manuel utilisateur
Unit
Unit UT601 Manuel utilisateur
Unit
Unit VC820 Manuel utilisateur
Unit
Unit UT60F Manuel utilisateur
Unit
Unit UT151A Manuel utilisateur
Unit
Unit UT89XE Manuel utilisateur
Manuels Multimètre populaires d'autres marques
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuel utilisateur
PeakTech
PeakTech 4000 Manuel d'utilisation et d'entretien
YOKOGAWA
YOKOGAWA 90050B Manuel utilisateur
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuel utilisateur
Fluke
Fluke 8846A Manuel d'utilisation et d'entretien
Tempo Communications
Tempo Communications MM200 Manuel utilisateur
