Unit UT203 Manuel utilisateur
Digital Clamp Multimeters
P/N: 41416301
Registered Design No.: ZL02 3 357791.6
UT203/204
Table of Contents
Overview
Unpacking Inspection
Safety Information
Rules For Safe Operation
International Electrical Symbols
The Meter Structure
Rotary Switch
Functional Buttons
The Effectiveness of Functional Buttons
Display Symbols
Measurement Operation
A. DC/AC Voltage Measurement
B. Measuring Resistance
C. Testing Diodes
D. Testing for Continuity
E. Frequency Measurement
F. Duty Cycle Measurement
G. DC/AC Current Measurement
3
4
5
6
9
10
11
12
14
15
18
18
20
22
24
26
28
30
Title Page
Model UT203/204: OPERATING MANUAL
1
Sleep Mode
Specifications
A. General Specifications
B. Environmental Requirements
Accuracy Specifications
A. DC Voltage
B. AC Voltage
C. Resistance
D. Diode Test
E. Continuity Test
F. Frequency
G. Duty Cycle
H. DC Current
I. AC Current
Maintenance
A. General Service
B. Replacing the Battery
32
33
33
34
35
35
36
37
37
38
39
40
40
42
44
44
45
Title Page
Model UT203/204: OPERATING MANUAL
2
Overview
This Operating Manual covers information on safety and cautions. Please read the
relevant information carefully and observe all the Warnings and Notes strictly.
Warning
To avoid electric shock or personal injury, read the “Safety Information” and “Rules
for Safe Operation” carefully before using the Meter.
Digital Clamp Multimeter Model UT203/UT204 (hereafter referred to as “the Meter”)
are 3 3/4 digits with steady operations, fashionable structure and highly reliable
measuring instrument. The Meter uses large scale of integrated circuit with double
integrated A/D converter as its core and has full range overload protection.
The Meter can not only measure AC/DC Voltage, AC/DC Current, Frequency, Duty
Cycle, Resistance, Diodes, Continuity but also it has Data Hold, Sleep Mode and
Relative Mode features.
UT204 has an extra True RMS feature.
Model UT203/204: OPERATING MANUAL
3
Unpacking Inspection
Open the package case and take out the Meter. Check the following items carefully
to see any missing or damaged part:
Item Description Qty
1
2
3
4
5
English Operating Manual
Test Lead
Test Clip
Carrying Bag
9V Battery (NEDA1604, 6F22 or 006P)
1 piece
1 pair
1 pair
1 piece
1 piece
In the event you find any missing or damage, please contact your dealer immediately.
Model UT203/204: OPERATING MANUAL
4
Safety Information
This Meter complies with the standards IEC61010: in pollution degree 2, overvoltage
category (CAT. II 600V, CAT. III 300V) and double insulation.
CAT. II: Local level, appliance, PORTABLE EQUIPMENT etc., with smaller transient
overvoltages than CAT. III.
CAT. III: Distribution level, fixed installation, with smaller transient overvoltages than
CAT. IV
Use the Meter only as specified in this operating manual, otherwise the protection
provided by the Meter may be impaired.
In this manual, a Warning identifies conditions and actions that pose hazards to the
user, or may damage the Meter or the equipment under test.
A Note identifies the information that user should pay attention to.
International electrical symbols used on the Meter and in this Operating Manual are
explained on page 9.
Model UT203/204: OPERATING MANUAL
5
Rules For Safe Operation
Warning
To avoid possible electric shock or personal injury, and to avoid possible damage
to the Meter or to the equipment under test, adhere to the following rules:
Before using the Meter inspect the case. Do not use the Meter if it is damaged
or the case (or part of the case) is removed. Look for cracks or missing plastic.
Pay attention to the insulation around the connectors.
Inspect the test leads for damaged insulation or exposed metal. Check the test
leads for continuity. Replace damaged test leads with identical model number
or electrical specifications before using the Meter.
Do not apply more than the rated voltage, as marked on the Meter, between the
terminals or between any terminal and grounding. If the value to be measured
is unknown, use the maximum measurement position and reduce the range step
by step until a satisfactory reading is obtained.
When measurement has been completed, disconnect the connection between
the test leads and the circuit under test, remove the testing leads away from the
input terminals of the Meter and turn the Meter power off.
l
l
l
l
Model UT203/204: OPERATING MANUAL
6
The rotary switch should be placed in the right position and no any changeover
of range shall be made during measurement is conducted to prevent damage of
the Meter.
Do not carry out the measurement when the Meter’s back case and battery
compartment are not closed to avoid electric shock.
Do not input higher than 600V between the two Meter’s input terminal to avoid
electric shock and damages to the Meter.
When the Meter working at an effective voltage over 60V in DC or 30V rms in AC,
special care should be taken for there is danger of electric shock.
Use the proper terminals, function, and range for your measurements.
Do not use or store the Meter in an environment of high temperature, humidity,
explosive, inflammable and strong magnetic field. The performance of the Meter
may deteriorate after dampened.
When using the test leads, keep your fingers behind the finger guards.
Disconnect circuit power and discharge all high-voltage capacitors before testing
resistance, continuity and diode.
Replace the battery as soon as the battery indicator appears. With a low
battery, the Meter might produce false readings that can lead to electric shock
and personal injury.
When servicing the Meter, use only the same model number or identical electrical
specifications replacement parts.
l
l
l
l
l
l
l
l
l
l
Model UT203/204: OPERATING MANUAL
7
When servicing the Meter, use only the same model number or identical electrical
specifications replacement parts.
The internal circuit of the Meter shall not be altered at will to avoid damage of
the Meter and any accident.
Soft cloth and mild detergent should be used to clean the surface of the Meter
when servicing. No abrasive and solvent should be used to prevent the surface
of the Meter from corrosion, damage and accident.
The Meter is suitable for indoor use.
Turn the Meter off when it is not in use and take out the battery when not using
for a long time.
Constantly check the battery as it may leak when it has been using for some time,
replace the battery as soon as leaking appears. A leaking battery will damage
the Meter.
l
l
l
l
l
l
Model UT203/204: OPERATING MANUAL
8
International Electrical Symbols
AC (Alternating Current)
DC (Direct Current)
AC or DC
Grounding
Double Insulated
Warning. Refer to the Operating Manual
Deficiency of Built-In Battery
Continuity Test
Diode
Fuse
Conforms to Standards of European Union
Model UT203/204: OPERATING MANUAL
9
Autres manuels pour UT203
1
Ce manuel convient aux modèles suivants
1
Table des matières
Autres manuels Unit Multimètre
Unit
Unit UT57 Manuel utilisateur
Unit
Unit UT70D Manuel utilisateur
Unit
Unit UT71 Manuel utilisateur
Unit
Unit UT70A Manuel utilisateur
Unit
Unit UT81C Manuel utilisateur
Unit
Unit UT60F Manuel utilisateur
Unit
Unit UT161 Series Manuel utilisateur
Unit
Unit UT58A Manuel utilisateur
Unit
Unit TU13BA Manuel utilisateur
Unit
Unit UT20B Manuel utilisateur
Unit
Unit UT81B Manuel utilisateur
Unit
Unit UT131A Manuel utilisateur
Unit
Unit UT70B Manuel utilisateur
Unit
Unit UT801 Manuel utilisateur
Unit
Unit UT151A Manuel utilisateur
Unit
Unit UT201 Manuel utilisateur
Unit
Unit UT33B Manuel utilisateur
Unit
Unit UT50A Manuel utilisateur
Unit
Unit UT58E Manuel utilisateur
Unit
Unit VC820 Manuel utilisateur
Manuels Multimètre populaires d'autres marques
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuel utilisateur
PeakTech
PeakTech 4000 Manuel d'utilisation et d'entretien
YOKOGAWA
YOKOGAWA 90050B Manuel utilisateur
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuel utilisateur
Fluke
Fluke 8846A Manuel d'utilisation et d'entretien
Tempo Communications
Tempo Communications MM200 Manuel utilisateur
