Unit UT71B Manuel utilisateur
6
Model UT71A/B/C/D/E: OPERATING MANUAL
Unpacking Inspection
Open the package case and take out the Meter. Check the items shown on Table 1-1 carefully to see any missing
or damaged part:
Table 1-1. Unpacking Inspection
Item Description Qty
In the event you find any missing or damage, please contact your dealer immediately.
1
2
3
4
5
6
7
8
9
10
English Operating Manual
Test Lead
K-Type (nickel chromium ~ nickel silicon) Point Contact Temperature Probe (It is
only suitable for measuring temperature under 230 oC
Alligator Clip
Test Clip
USB interface cable
CD-ROM (Installation Guide & Computer Interface Software)
Carrying Bag
Power Adaptor (UT71E only)
9V Battery (NEDA 1604, 6F22, 006P)
1 piece
1 pair
1 piece
1 piece
1 pair
1 piece
1 piece
1 piece
1 piece
1 piece
7
Model UT71A/B/C/D/E: OPERATING MANUAL
Safety Information
This Meter complies with the standards IEC61010 safety
measurement requirement: in pollution degree 2,
overvoltage category (CAT. III 1000V, CAT.IV 600V)
and double insulation.
CAT. III: Distribution level, fixed installation, with smaller
transient overvoltage than CAT. IV
CAT.IV: Primary supply level, overhead lines, cable
systems etc.
Use the Meter only as specified in this operating manual,
otherwise the protection provided by the Meter may be
impaired.
In this manual, a Warning identifies conditions and
actions that may pose hazards to the user, or may
damage the Meter or the equipment under test.
A Note identifies the information that user should pay
attention to.
International electrical symbols used on the Meter and
in this Operating Manual are explained on page 9.
Rules For Safe Operation
Warning
To avoid possible electric shock or personal injury,
and to avoid possible damage to the Meter or to the
equipment under test, adhere to the following rules:
Before using the Meter inspect the case. Do not
use the Meter if it is damaged or the case (or part
of the case) is removed. Look for cracks or missing
plastic. Pay attention to the insulation around the
connectors.
Inspect the test leads for damaged insulation or
exposed metal. Check the test leads for continuity.
Replace damaged test leads with identical model
number or electrical specifications before using the
Meter.
Do not apply more than the rated voltage, as marked
on the Meter, between the terminals or between any
terminal and grounding.
The rotary switch should be placed in the right
position and no any changeover of range shall be
made during measurement is conducted to prevent
damage of the Meter.
l
l
l
l
8
Model UT71A/B/C/D/E: OPERATING MANUAL
l
l
l
l
l
l
l
l
l
l
l
l
l
l
When the Meter working at an effective voltage over
60V in DC or 30V rms in AC, special care should be
taken for there is danger of electric shock.
Use the proper terminals, function, and range for
your measurements.
If the value to be measured is unknown, use the
maximum measurement position.
Do not use or store the Meter in an environment of
high temperature, humidity, explosive, inflammable
and strong magnetic field. The performance of the
Meter may deteriorate after dampened.
When using the test leads, keep your fingers behind
the finger guards.
Disconnect circuit power and discharge all high-
voltage capacitors before testing resistance,
continuity, diodes.
Before measuring current, check the Meter's fuses
and turn off power to the circuit before connecting
the Meter to the circuit.
Replace the battery as soon as the battery indicator
appears. With a low battery, the Meter might
produce false readings that can lead to electric
shock and personal injury.
When servicing the Meter, use only the same model
number or identical electrical specifications
replacement parts.
The internal circuit of the Meter shall not be altered
at will to avoid damage of the Meter and any accident.
Soft cloth and mild detergent should be used to
clean the surface of the Meter when servicing. No
abrasive and solvent should be used to prevent the
surface of the Meter from corrosion, damage and
accident.
The Meter is suitable for indoor use.
Turn the Meter off when it is not in use and take out
the battery when not using for a long time.
Constantly check the battery as it may leak when it
has been using for some time, replace the battery
as soon as leaking appears. A leaking battery will
damage the Meter.
9
Model UT71A/B/C/D/E: OPERATING MANUAL
International Electrical Symbols
Symbols used on the Meter and in this manual are explained in Table1-2.
Table 1-2. International Electrical Symbols
AC or DC
DC Measurement
AC Measurement
Grounding
Double Insulated
Warning. Refer to the Operating Manual
Deficiency of Built-In Battery
Conforms to Standards of European Union
10
Model UT71A/B/C/D/E: OPERATING MANUAL
Chapter 2
Getting Acquainted
Turning the Meter On
To turn the Meter on, turn the rotary switch from OFF
to any switch setting.
Battery Considerations
The Meter uses one 9V Battery (NEDA 1604, 6F22,
006P). The following paragraphs describe several
techniques used to conserve battery power.
Automatic Power Off
The display blanks and the Meter goes into a "sleep"
mode if you have not changed the rotary switch position
or pressed a button for a set period. While in Sleep
mode, pressing the blue button or turning the rotary
switch could turn the Meter on. The Meter then returns
to the display for the function selected with the rotary
switch; all previously activated button features are
discarded.
Automatic Backlight Off
Press LIGHT button to turn the backlight on and press
LIGHT again to turn it off. Press EXIT to exit the feature.
Press LIGHT to select the backlight level (low or high).
In Setup menu (see Chapter 5), you could specify a
time to automatically turn off the backlight (10 seconds,
20 seconds, 30 seconds or OFF). If the period is set
to OFF, the backlight feature is disabled.
The automatic power off is preset to 10 minutes. From
the Setup menu (see Chapter 5), you could specify a
time (10 minutes, 20 minutes, 30 minutes or OFF). If
you set to OFF, the Meter retains on until you turn the
rotary switch to OFF or the battery becomes too weak.
11
Model UT71A/B/C/D/E: OPERATING MANUAL
Low Battery Indication
A constant battery icon ( ) in the upper left corner of
the display notifies you that the batteries are low and
should be replaced.
Warning
To avoid false readings, which could lead to possible
electric shock or personal injury, replace the battery as
soon as the battery icon ( ) appears.
The Meter Structure
The Figure 2-1 shows the Meter structure.
1. LCD Display
2. Functional Buttons
3. Rotary Switch
4. Input Terminals
Figure 2-1. Meter Structure
12
Model UT71A/B/C/D/E: OPERATING MANUAL
Rotary Switch
Turn the Meter on by selecting any measurement function. The Meter presents a standard display for that function.
The display may also be influenced by some of the choices made in Setup.
Use the blue button to select any rotary switch alternate function (labeled in blue letters).
When you turn the rotary switch from one function to another, a display for the new function appears. Button choices
made in one function do not carry over into another function.
The Table 2-1 described each rotary switch position
13
Model UT71A/B/C/D/E: OPERATING MANUAL
Table 2-1. Rotary Switch Selections
Rotary
Switch Position Rotary Switch Function Blue Key Function
Turn the Meter off
DC voltage measurement
AC voltage measurement
AC or DC voltage measurement
DC millivoltage measurement
DC millivoltage measurement
Resistance measurement
Power measurement
Capacitance measurement
Centigrade temperature measurement
None
None
None
Toggle betweenAC or DC voltage measurement
Frequency measurement
Frequency signal duty cycle measurement
None
Diode test
Continuity test
None
None
Fahrenheit temperature measurement
OFF
V
Hz % mV
ºC ºF
l
l
V
V
l
l
mV
(UT71B/C/D)
W (UT71E only)
(UT71B/C/D )
(UT71A/B/C/D )
(UT71A/B/C/D )
(UT71E only)
(UT71A/E)
14
Model UT71A/B/C/D/E: OPERATING MANUAL
Rotary
Switch Position Rotary Switch Function Blue Key Function
Centigrade temperature measurement
AC or DC current measurement (400µA,4000µA)
AC or DC current measurement (40mA,400mA)
AC or DC current measurement (10A)
Fahrenheit temperature measurement
Frequency measurement
Frequency signal duty cycle measurement
Toggle between AC or DC current
Toggle between AC or DC current
4~20mA loop current as % reading
Toggle between AC or DC current
mA
µA
A
(4~20mA)
%
l
l
l
(UT71E only)
∫C ∫F
Hz %
15
Model UT71A/B/C/D/E: OPERATING MANUAL
Functional Buttons
The buttons activate features that augment the function selected with the rotary switch. The buttons are shown
in Table 2-2.
STORE
RECALL
Press the button once to access the main feature (e.g. STORE).
To access the first additional feature of the button (e.g. RECALL), press and hold the button for over 1 second to
access this additional feature. This additional feature appears right above or on the left hand side of the appropriate
keys.
To access the second additional feature of the button (e.g. ), press once the button again while the Meter has
already entered the first additional feature (e.g. RECALL). The second additional feature appears on the right hand
side above the appropriate keys.
The RANGE and EXIT buttons has only one additional feature.
Ce manuel convient aux modèles suivants
4
Table des matières
Autres manuels Unit Multimètre
Unit
Unit UT33B Manuel utilisateur
Unit
Unit UT51-55 Manuel utilisateur
Unit
Unit UT60A Manuel utilisateur
Unit
Unit UT71A Manuel utilisateur
Unit
Unit UT58E Manuel utilisateur
Unit
Unit UT131A Manuel utilisateur
Unit
Unit UT58D Manuel utilisateur
Unit
Unit UT60C Manuel utilisateur
Unit
Unit UT8806E Manuel utilisateur
Unit
Unit UT603 Manuel utilisateur
Unit
Unit MIE0141 Manuel utilisateur
Unit
Unit UT131B Manuel utilisateur
Unit
Unit UT60B Manuel utilisateur
Unit
Unit UT120C Manuel utilisateur
Unit
Unit UT70B Manuel utilisateur
Unit
Unit UT33B Manuel utilisateur
Unit
Unit UT202A Manuel utilisateur
Unit
Unit UT208A Manuel utilisateur
Unit
Unit UT202A Manuel utilisateur
Unit
Unit UT801 Manuel utilisateur
Manuels Multimètre populaires d'autres marques
Gossen MetraWatt
Gossen MetraWatt METRAmax 6 Manuel utilisateur
PeakTech
PeakTech 4000 Manuel d'utilisation et d'entretien
YOKOGAWA
YOKOGAWA 90050B Manuel utilisateur
Gossen MetraWatt
Gossen MetraWatt METRALINE DMM16 Manuel utilisateur
Fluke
Fluke 8846A Manuel d'utilisation et d'entretien
Tempo Communications
Tempo Communications MM200 Manuel utilisateur
