UEi PET1 Manuel utilisateur

1-800-547-5740 • Fax: (503) 643-6322

www.ueitest.com • email: [email protected]

PET1

INSTRUCTION MANUAL

Introduction

The PET1 is a convenient pocket-size multifunction tester, which

combines the latest digital technology with an advanced sensor to

detect high/low AC voltage.

Features include

• Non-contact AC voltage test: from 12-600 V AC

(with adjustable sensitivity)

• Detects high and low AC Voltage

• Continuity check: 0 - 80 MΩ

• Work light

Safety Notes

• The tester should not be used to test voltages above the stated

rated voltage.

• Operating temperature within -10˚ to +50˚C (14˚ to 122˚F)

and a frequency range from 50 to 500 Hz. Best results at a

temperature range up to 86˚F, humidity 80% at altitude up to

6,000 feet.

• The tester must be tested on a known voltage source to make sure

it is operating properly.

• Do not use in the presence of moisture, (e.g. dew or rain)

• Do not use if damaged

• Static electricity may be generated by rubbing the “BODY” of the

tester (when pressing the switch) thus causing the audible and

visual alert to function

• The flashlight lights up when the switch is pressed

• In case of doubt, please consult a qualified technician

Self-Test Function

Prior to use, perform a self-test to ensure full functionality. Press the

switch down and touch the "TIP" with your free hand.

The LED lights red and buzzer sounds indicating " NORM AL FUNCTION ".

Non-Contact AC Voltage Testing

Press the switch to test.

To locate "LIVE/HOT" side of a wire, lower sensitivity until the detector

only sounds on one wire.

Broken wire/fault finding

"FAULT/BREAK" point of a wire is indicated by an interruption in

sound and light (red LED).

Proper connection check

Move the tester close to an un-energized appliance. The buzzer comes

ON when power is applied.

PET1-MAN P. 1

LED

Ground/Earthing check

Move the tester close to a plugged-in (not turned on appliance). The

buzzer comes ON if the "GROUND/EARTHING" is not connected at

the outlet.

NOTE:

1. To Reduce Sensitivity

If sensitivity is too high, rotate adjustment left (counter-clockwise)

2. Static electricity may be generated by rubbing the plastic housing

thus causing an indication (LED blinks).

3. The sensitivity may be reduced under high humidity environments.

4. Test only insulated (unshielded) wires that are connected to

AC voltage.

5. Wires inside concrete walls or metal conduit cannot be detected.

Continuity Check

WARNING!

Be sure to disconnect any AC mains or high voltage!

Press test switch then contact one side of an object to the "TEST PIN"

and the other side of the object with your free hand. The PET1 will

easily identify"GOOD" or "BAD" fuses, bulbs, heating elements,

wiring etc.

PET1-MAN P. 2

Flashlight

Battery Replacement

Twist the clip either left or right and remove the cover. Replace with

fresh batteries as shown (Fig. 1).

WARNING!

Be sure to disconnect any AC mains or high voltage!

Standard Accessories

Standard

1.5V button battery (size: 11.6 x 5.4mm) . . . . . . . . . . . . . . . . . .AB13

GOOD

LED blinks and

buzzer sounds

FAULT

No response

LED (1) lights up

when switch is

pressed

Twist to open

battery

compartment

Buzzer

PET1-MAN P. 3

Inside of battery

compartment -

Insert batteries

(+) up and

(-) down

LED Power on

when green.

Flashing increases

with intensity

Test Pin

Flash Light, super bright

white LED (1)

Adjustment knob

Press switch

(Press: ON)

(Release: OFF)

Clip

Battery compartment

(cover)

(Fig 1)

Limited Warranty

The PET1 is warranted to be free from defects in materials and workmanship for a period of

three years from the date of purchase. If within the warra n ty period your instrument should

become inoperative from such defects, the unit will be repaired or replaced at UEi’s option.

This warra n ty covers normal use and does not cover damage which occurs in shipment or

failure which results from alteration, tampering, accident, misuse, abuse, neglect or improper

maintenance. Batteries and consequential damage resulting from failed batteries are not

covered by warra n ty.

Any implied warranties, including but not limited to implied warranties of merchantability

and fitness for a particular purpose, are limited to the express warranty. UEi shall not

be liable for loss of use of the instrument or other incidental or consequential damages,

expenses, or economic loss, or for any claim or claims for such damage, expenses or

economic loss. A purchase receipt or other proof of original purchase date will be required

before warra n ty repairs will be rendered. Instruments out of warra n ty will be repaired

(when repairable) for a service charge. Return the unit postage paid and insured to:

1-800-547-5740 • FAX: (503) 643-6322

www.ueitest.com • Email: [email protected]om

This warranty gives you specific legal rights. You may also have other rights which vary from

state to state.

PET1

Pocket Electrical Tester

PLEASE

RECYCLE

Table des matières

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur