UEi C165 Manuel utilisateur

C165 QuiCk Start Guide

GETTING STARTED

Press ”Power” in fresh air and allow to count-

down for Fresh Air purge.

Rotate selector dial to Flue 1. In fresh air, O2

reading should be 20.9% ±0.3%.

Rotate selector dial to Flue 2. In fresh air, CO reading

should be zero (0).

Connect the ﬂue probe thermocouple connector to T1.

Connect ﬂue probe to water trap.

Connect optional probe to T2.

T2 T1

P1 P2

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

FRESH

AIR

PURGE

TIME 60

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

NAT GAS

C02 8.3%

O2 20.9%

EfG O2++%

Tf 42.4%

Ta 0.03m

Prs/Temp

BASIC CO/COMBUSTION ANALYSIS

Insert Flue probe into stack.

Adjust cone so end of the probe is

approximately at the center of the

stack.

NOTE: You will have to drill a hole

at least 3/8”. Use appropriate

sealing method after testing.

Rotate selector dial to Flue 1 for:

CO2, O2, Gross efﬁciency, Flue

temperature, Inlet temperature.

Fuel type can be changed via

MENU or STATUS setting

Rotate selector dial to Flue 2 for:

CO (ppm), Losses calculated, Excess

air %, pressure reading

Fuel type can be changed via

MENU or STATUS setting.

Make any adjustments as needed for

proper combustion and wait for ana-

lyzer to display change in readings.

(Repeat as necessary).

Once complete, remove probe from

stack, allow analyzer to purge in

fresh air until CO sensor readings

return to ZERO (0) and O2readings

reading return to 0% to 21%.

Continue to the next test or power

analyzer off by pressing On/Off, if

ﬁnished.

NOTE: Print and store functions may

be used at any time during testing.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

FRESH AIR

PURGE

TURN

OFF

TIME 5

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

NAT GAS

CO 80P

COa 80P

LOSS O2++%

XAIR O2++%

PRS 0.00i

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

NAT GAS

C02 8.3%

O2 20.9%

EfG O2++%

Tf 42.4%

Ta 0.03m

Prs/Temp

DIFFERENTIAL TEMPERATURE TEST

Rotate the selector dial to

Pressure/Temperature.Press ”Pump” to ZERO

(0) pressure sensor.

Connect probe to T1.

Connect probe to T2.

Compatible with any K-Type

thermocouple probe or clamp.

Connect thermocouples in

test location to start testing

Observe T1, T2 and

differential (Delta T).

Press “Print” to print

results.

Press and Hold to log

results.

T2 T1

P1 P2

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

PRS 0.04i

i= inH20

T1 167,1F

T2 104.3F

T 62.8F

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

PRS/TEMP

PRESS

ZERO

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

Prs/Temp

PRS 0.04i

i= inH20

T1 167,1F

T2 104.3F

T 62.8F

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

Prs/Temp

PRS/TEMP

PRESS

ZERO

All manuals and user guides at all-guides.com

all-guides.com

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

BLOWER ON

NAT GAS

CO 0p

O2 20.0%

XAIR 02++%

TIME 60

Prs/Temp

DRAFT & STATIC PRESSURE TEST

T2 T1

P1 P2

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

Prs/Temp

PRS 0.04i

i= inH20

T1 167,1F

T2 104.3F

T 62.8F

Rotate the selector dial to

Pressure/Temperature. Press ”Pump” to ZERO

(0) pressure sensor.

Connect true draft hose to PI.

Connect to P2 for differential.

Place probe tip in stack to

measure draft.

Connect static pressure hose

for measure differential

pressure.

Place true draft probe tip in the

ﬂue to measure draft.

You can also use the

combustion probe for

measuring pressure.

Press “Print” to print

results.

Press and Hold to log

results.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

PRS/TEMP

PRESS

ZERO

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

Prs/Temp

PRS/TEMP

PRESS

ZERO

HEAT EXCHANGER TEST

Rotate selector dial to

EXCH Test, press the

“Print”.

Conﬁrm the Fuel Type.

Scroll or to switch

a different fuel type.

Press to select fuel

type.

NOTE: The analyzer will

perform a fresh air purge

if it did not perform one on

start up. Otherwise it will

skip past the zeroing step to

the Blower Off screen. See

manual for details.

Press to continue.

Ensure the analyzer is

in fresh air during the

countdown. The screen

will automatically advance

when complete.

Call for heat.

Observe and wait for O2

readings to stabilize.

After the blower turns on,

press the Button to

start the Post-Blower test.

There are many methods to test heat exchanger integrity. One of these is to observe Excess Air, O2AND CO readings both before and after the blower turns

on. If the heat exchanger is sealed your O2and CO readings should remain fairly stable. A breach in the heat exchanger may allow fresh air to be forced into

the ﬂue after the blower turns on due to a pressure increase in the plenum. The result may be a rise in the measured O2in the stack gas and an increase in the

Excess Air. In some sealed systems the fresh air drawn in the breach may reduce the combustion available leading to an increase in the CO reading. If either of

these situations are present it is probable that there is a problem with the Heat Exchanger which may require additional testing and inspection.

NOTE: Many cracks are invisible to borescopes or the naked eye and only open or separate from pressure or temperature during operation.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

EXCHANGE

TEST

START

PRESS

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SETUP

FUEL TYPE

NAT GAS

PRESS

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

EXCHANGE

WITH PROBE

IN FRESH

AIR

PRESS

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

BLOWER OFF

NAT GAS

CO 0p

O2 20.0%

XAIR 02++%

PRESS

Prs/Temp

The analyzer will wait 60

seconds and then record the

Post-Blower values for CO,

02and Excess Air.

Test results will automati-

cally be stored to exchange

reports. Report includes both

Pre and post Blower test

segments.

Press to start printing.

See REPORTS section in

this guide.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

EXCHANGE

ZEROING

TIME 60

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

LOG No. 10

12:00:00

CO 0p

O2 20.0%

XAIR 02++%

Prs/Temp

All manuals and user guides at all-guides.com

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

Prs/Temp

O2 20.9%

CO 0P

C02 8.3%

XAIR 42.4%

PRS -0.02i

Ta 80.3F

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SETUP

UNITS

SCREEN

REPORT

SERVICE

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

ROOM CO

TEST 1/15

INT. 120s

CO 5p

LIMIT 10p

ALARM 30p

Prs/Temp

REPORTS: PRINTING & VIEWING

HIGH CO ALERT

Press ”Print” to start

printouts of results from any

test screen.

Press during printing to

cancel.

Press and hold to log

current readings.

Align printer above Analyzer.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

NAT GAS

Ra 0.0010

CO 80P

C02 8.3%

XAIR 42.4%

PRS 0.03m

Prs/Temp

To view test results,

rotate dial to Menu.

Scroll or to Report

Press to select.

Scroll or to type

of test wanted.

Press to select.

[Exchange shown]

Press to select View.

Press to select

report log number. When

indicator lights blink,

use or to scroll

through logged reports.

Press to view a

selected report log.

Menu Room CO

Status

Aux

Flue1 Flue2

C165

Com Test

Exch Test

NAT GAS

Ra 0.0010

CO 80P

C02 8.3%

XAIR 42.4%

PRS 0.03m

Prs/Temp

At 1000 ppm CO the screen will display HIGH CO and an indicator light will ﬂash and analyzer will beep several times. Above 2000 ppm the purge pump starts.

Print and Log easily from the following test screens: Aux, Flue 1, Flue 2, Commission Test, Pressure/Temperature, Exchange Test and Room CO

CO ROOM TEST

No probes or hose connections

required for this test.

Rotate selector dial to ROOM CO.

Press ”Print” to start the

GENERAL test.

Press start the test. CO readings will be logged every 2

minutes for a 30 minute time span.

Readings will be stored once the 30

minute test is completed.

Press to print results.

Test results will automatically be

stored in ROOM CO reports.

See REPORTS section in this guide.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

ROOM CO

LOG No. 1

TEST 1

CO 5p

GENEAL

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SELECT

ROOM CO

TEST TYPE

GENERAL

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

ROOM CO

PRESS

START

Prs/Temp

Great for checking ambient CO and back drafting situations

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SETUP

UNITS

SCREEN

REPORT

SERVICE

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SCREEN

CONTRAST

BACKLIGHT

AUX

BACK

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

AUX

LINE 1

LINE 2

LINE 3

LINE 4

LINE 5

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

SCREEN

AUX

LINE 5

PRS 0.02i

Prs/Temp

AUX SETTING

Rotate selector dial to Menu.

Scroll or to Screen.

Press ”Print” to select.

Scroll or to AUX.

Press to select.

Scroll or to customize

any Line.

Press to select.

[Line 5 shown]

Scroll or to select

the parameter for this line.

Press to select.

[Pressure shown]

Rotate selector dial to AUX

to view.

Custom selections will now

display in AUX mode.

Programmable Auxiliary screen allows for Tech selectable test parameters to be chosen.

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

REPORT

AUX

COMBUSTION

PRS/TEMP

EXCHANGE

Prs/Temp

Menu Room CO

Status

Aux

Flue1 Flue 2

C165

Com Test

Exch Test

LOG No. 9

12:00:00

CO 0p

02 20.9%

XAIR O2++%

Prs/Temp

All manuals and user guides at all-guides.com

www.ueitest.com Email: [email protected]

USA: 1-800-547-5740 • 503-643-6322

CANADA: 1-877-475-0648 • 604-278-4311

MAIN MENU SUB MENU OPTIONS / COMMENTS

SETUP LANGUAGE English

SET TIME HH:MM:SS format

e.g. 7 am = 07:00:00, 7 pm = 19:00:00

SET DATE MM/DD/YY format

PRINTER KM IRP

KANE IRP-2

WIRELESS (if installed)

SERIAL

PASSKEY 1111 (wait 5 secs after entering last digit)

BACK

UNITS FUEL TYPE NAT GAS, TOWN GAS, COKE GAS, PROPANE, BUTANE, LPG, LIGHT OIL, BIO OIL, WOOD

PELLETS, BIO GAS, USER 1 to 5

FUEL ORIGIN UK, FRANCE, SPAIN, N AMERICA, BELGIUM, NETHERLAND

EFFICIENCY GROSS, NET, GROSS COND, NET COND

PRESSURE FILTER: OFF = normal response. ON = slower (damped) response

RESOLUTION: LOW = e.g. 0.00i inH20 resolution. HIGH = displays to an extra decimal place

UNITS: mbar, Pa, PSI, mmHg, hPa, inH2O, mmH20, kPa, psi

TIME: Test units not available in North American market

BACK:

GAS ppm, ppm(n), mg/m3, mg/m3(n), mg/kWh, mg/kWh(n)

TEMP C, F

02REF Up/down to set value (3% default)

NOx CALC Up/down to set value (5% default)

BACK

SCREEN CONTRAST Factory setting is 14

BACKLIGHT 0 to 300 secs

AUX Enables users to customize the parameters on the AUX display: LINE 1, LINE 2, LINE 3,

LINE 4, LINE 5, LINE 6, BACK

BACK

REPORT AUX Stored AUX tests

VIEW, DEL ALL, BACK

COMBUSTION Stored combustion tests:

VIEW, DEL ALL, BACK

COMMISSION Stored commission tests:

VIEW, DEL ALL, BACK

PRS/TEMP Stored pressure tests:

VIEW, DEL ALL, BACK

EXCH Stored exchange tests:

VIEW, DEL ALL, BACK

ROOM CO Stored room CO tests:

VIEW, DEL ALL, BACK

HEADER LINE 1

LINE 2

BACK

SERVICE CODE Password protected for authorized service agents only. Leave set to 000000.

All manuals and user guides at all-guides.com

Autres manuels pour C165

Manuels Instrument de mesure populaires d'autres marques

Suaoki

Suaoki D40 Manuel utilisateur

Elster

Elster BK-G1.6 Manuel utilisateur

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuel

Duratool

Duratool D03128 Manuel utilisateur

Vega

Vega VEGAPULS 65 Manuel utilisateur

Tonghui

Tonghui TH2618B Manuel utilisateur

Tenmars

Tenmars TM-801 Manuel utilisateur

MSR

MSR 145 Manuel utilisateur

TPS

TPS WP-82 Manuel utilisateur

ELMETRON

ELMETRON CP-511 Manuel utilisateur

PCB Piezotronics

PCB Piezotronics 003C30 Manuel utilisateur

Tenma

Tenma 72-10465 Manuel utilisateur

Endress+Hauser

Endress+Hauser Proline Promag 50 Caractéristiques techniques

Siemens

Siemens SITRANS F Coriolis FCT030 Manuel de la liste des pièces

KLINGER

KLINGER CMF V Series Manuel utilisateur

EXFO

EXFO FTB-2 Manuel d'exploitation et d'entretien

Keysight

Keysight M8290A Manuel utilisateur

ADTEK

ADTEK MW-5 Manuel utilisateur