TYM ET350 ECONO Manuel utilisateur
TYM
OPERATOR’S MANUAL
FOR
TRACTORS
ET350 ECONO
#604-9, Namsan-dong, Changwon-city, Kyungnam, Korea ■TEL:82-55-279-4379, FAX:82-55-279-4447 ■www.tym.co.kr
JIANGDONG
Off-Road compression-Ignition Engine
Emission Control System Warranty statement
EMISSION RELATED SYSTEM DEFECT WARRANTY
The warranty period shall begin on the engine or equipment purchaser of certified fuel.
JIANGDING Group.co. warrants to the ultimate purchaser and each subsequent purchaser of certified
off-road compression-ignition engine (powering off-road machines and equipment), that such engine is;
1) Designed, built, and equipped so as to confirm with all applicable regulations adopted by the
Environmental Protection Agency.
2) Free from defects in materials and workmanship which cause the failure of a warranted part to be
identical in all material respects to the part as described in the engine manufacturer’s application for
certification for period of five years for 3000 hours of operation, whichever occurs first, for all engines
rated at 19kw and greater, except as noted below, in the absence of a device to measure hours of use, the
engine shall be warranted for a period of five years. For all engines rated less than 19kw, and for constant
speed engine rated under 37kw with rated speeds higher than or equal to 3000 rpm, the period of two
years or 1500 hours of operation, whichever occurs first, shall apply, in the absence of a device to
measure hours of use, the engine shall be warranted for a period of two years.
If a warranted part fails because of a defect during the terms of this warranty, JIANGDONG will repair or
replace it at any authorized JIANGDONG dealer. Any other parts damaged by the failure of a warranted
part will also be repaired or replaced. The repair and/or replacement will be made at no charge to the
owner for parts, labor and diagnosis. Any such part repaired or replaced under the warranty shall be
warranted for the remaining warranty periods.
In case of emergency, repairs may be performed at any service establishment, or by the owner, using any
replacement part.
JIANGDONG Group.co.will reimburse the owner for their expenses, including diagnostic charges for
such emergency repair. These expenses shall not exceed JIANGDONG Group.co. suggested retail price
for all warranted parts replaced, and labor charges based on JIANGDONG Group.co.recommended time
allowance for the warranty repair and geographically appropriate hourly labor rate.
A part not available within 30 days or a repair not being complete within 30 days constitute an emergency.
As a condition of reimbursement, replaced parts and receipt invoices must be presented at a place of
business of an authorized JIAGDONG engine dealer or other establishment and authorized by
JIANGDONG Group.co.
This warranty covers the following emission-related parts and components.
-Fuel Injection pump
-Nozzle Assembly
-Injection pipe
-Turbocharger (if equipped)
-Intake, Exhaust manifold
If failure of these components results in failure of another part, both will be covered by this warranty. Any
replacement part may be used for maintenance or repairs. The owner should ensure that such parts are
equivalent in design and durability to JIANGDONG genuine parts.
Use of non-genuine JIANGDONG parts does not invalidate the warranty. However JIANGDONG
Group.co. is not liable for parts, which are not genuine JIANGDONG parts.
RESPONSIBILITY AND LIMITATIONS.
These warranties are subject to the following:
JAINGDING Group.co.RESPONSIBILITIES.
During the emission warranty period, if a defect in material or workmanship of a warranted parts or
component is found. JIANGDONG Group.co.will provide;
-New, remanufactured, or repaired parts and-or components required to correct the defect.
Items replaced under this warranty become the property of JIANGDONG Group.co.
-Labor, during normal working hours, required to make the warranty repair.
This includes diagnosis and labor to remove and install the engine, if necessary.
Owner’s Warranty Responsibilities.
As the JIANGDING Group.co. off-road compression-ignition owner, you are responsible for the
performance of the required maintenance listed in your Owner’s Manual. JIANGDONG Group.co.
cannot deny warranty solely for the lack of required maintenance was the reason for the repair, then
the claim will be denied.
You are responsible for presenting your JIANDONG engine to a DIANGDONG Group.co.dealer as soon
as a problem exists. The warranty repairs should be completed in a reasonable amount of time, not to
exceed 30 days.
As the JIAMGDONG engine owner, you should also be aware that JIANGDONG Group.co.may deny you
warranty coverage if your JIANGDONG engine or parts has failed due to abuse, neglect, improper
maintenance or unapproved, modifications. If you have any questions regarding your warranty rights and
responsibilities, you should contact JIANGDONG Group.co.
Division at 1801 Quality Drive
LIMITATION
The emission control system defects warranty and the emission control system performance warranty shall
not apply to: - malfunctions in any part directly caused by abuse, misuse, modification, improper
adjustment except those done by a dealership during warranty service work, alterations, tempering
connections, improper or inadequate maintenance, neglect or use of leaded diesel or other fuels not
recommended in the owner’s Manual.
-Damage resulting from accident or an Act of God.
-Failure that are a direct result of a lack of performance of required emission control maintenance as
outlined in your Owner’ Manual.
-Parts or accessories used in applications for which they were not designed or not approved for use on the
engine by JIANGDONG Group.co.
-Parts not supplied by JIANGDONG Group.co.or damage to other parts caused directly by
non-JIANGDONG Parts or non-equivalent parts.
-The charge for diagnostic labor which does not lead to the determination that a warrantable condition
exists.
-JIANGDONG Group.co.is not responsible on which or consequential damages such as downtime or loss-
use of engine powered equipment.
-Although you purchase the equipment on which JIANGDONG engine is mounted, if the equipment is not
manufactured by JIANGDONG, you will make contact with purchasing dealer.
EMERGENCY SERVICE
If emergency Emission Control System Warranty service is required and the owner is unable to readily
locate an authorized JIANGDONG dealer or if a warranted part is available within 30 days, then, repairs
may be performed at any available service establishment, or by the owner, using any replacement part.
JIANGDONG will reimburse the owner for the owner’s expenses including diagnostic charges for such
emergency repair or replacement at JIANGDONG ’s suggested retail price for all warranted parts
replaced and labor charges based on JIANGDONG ‘s recommended time allowance for the warranty
repair and the geographically appropriate hourly labor rate. Replaced part and copies of paid original
receipts must be available for presentation to JIANGDONG as a condition of reimbursement for these
emergency repairs.
In addition, the owner must provide JIANGDONG a detailed description indicating why the situation
was considered an emergency and why an authorized JIANGDONG dealer was not being complete
within 30 days constitutes an emergency.
Thank you for purchasing our ET 350 ECONO tractor. ET 350 ECONO tractor is characterized by its
compact construction, and big excess power. With relevant implement, it can make various kind or work,
such as plowing, Rototilling, harrowing, seeding, harvesting, irrigation, electric generation,
transportation and gardening, etc…
The correct usage, adjustment and maintenance of the tractor may prolong their service life, and give
their full play. This book, for this reason, is complied to provide the above information for owners of the
tractor.The user of the tractor is required to read this book carefully before putting the tractor into
operation, and strictly to observe the regulations and instructions in using and servicing the tractors.
This Operation Manual excludes the information for engine chapter, which you can find on the separate
Engine Operation Manual attached with.
With the requirements of customers and the developments of engineering science, this product will be
improved continuously. So please notice the contents of the book may be somewhat not accordance with
the tractor you have owned. We will publish new one periodically.
FOREWARD
CONTENTS
CHEPTER 1 Main Specifications of Tractor …………………………………………………..
CHAPTER 2 Safety Regulations and Important Instructions..……………………………….
2.1 Safety Instructions …………………………………………………………………………
2.2 Safety Regulations …………………………………………………………………………
2.3 Important Instructions. ……………………………………………………………………..
2.4 ROPS (Roll Over Protection Structure) …………………………………………………..
2.5 Safety signs…………………………………………………………………………………
CHAPTER 3 Oiling and Running – in process ….………………………………………………
3.1 Oiling and Fueling of the Tractor ……………………………………………………………
3.2 Running – In of a New Tractor ………………………………………………………………
3.3 Work on the Tractor after Running – in ……………………………………………………...
CHAPTER 4 Operation of Tractor ……………………………………………………………….
4.1 Controls and Instruments …………………………………………………………………….
4.2 Operating and Driving ………………………………………………………………………..
4.3 Operation of Working Facilities ……………………………………………………………...
4.4 Operation of Electrical Equipment …………………………………………………………...
CHAPTER 5 Important Adjustments …………….………………………………………………
5.1 Important Adjustments Date of Engine ……………………………………………………….
5.2 The Components of Clutch ……………………………………………………………………
5.3 Adjustments of Transmission …………………………………………………………………
5.4 Adjustments of Brakes ………………………………………………………………………..
5.5 Adjustments of Final Drive ……………………………………………………………………
5.6 Fully Hydraulic steering system……………………………………………………………….
5.7 Lifter Hydraulic Tube system …………………………………………………………………
5.8 Adjustment of Tread …………………………………………………………………………..
5.9 Adjustment of Lifter …………………………………………………………………………..
5.10 The Operation Controls of Front Drive Axle …………………………………………………
5.11 The Structure and Adjustment of Front Drive Axle…………………………………………
5.12 The Structure, Installation and Disassembly of Transmission Shaft and Transfer Case……
1
4
4
9
9
10
13
17
17
18
19
20
20
24
26
27
30
30
30
35
37
37
38
40
41
42
43
44
47
5.13 Connection and adjustment of Front Axle and Its Bracket ……………………………….
5.14 Adjusting of Front Wheel Deflection Angle and Toe – in ……………………………….
5.15 Lubricating Points of Front Drive System and Steering System …………………………
CHAPTER 6 Technical Maintenance of Tractor..……………………………………………...
6.1 Technical Maintenance per Shift …………………………………………………………..
6.2 1st Technical Maintenance …………………………………………………………………
6.3 2nd Technical Maintenance ………………………………...………………………………
6.4 3rd Technical Maintenance ………………………………………………………………...
6.5 Special Maintenance of Winter ……………………………………………………………..
CHAPTER 7 Trouble Shooting …………………………………………………………………..
7.1 Engine ……………………………………………………………………………………….
7.2 Chassis ………………………………………………………………………………………
7.3 Electrical System ……………………………………………………………………………
CHAPTER 8 APPENDICES …………………………………………………………..…………..
8.1 Tightening Torque of important Bolts and Nuts …………………………………………….
8.2 Diagram of Transmission System …………………………………………………………...
8.3 Electrical system wiring Diagram …………………………………………………………...
8.4 Fuel System Diagram ……………………………………………………………………..…
8.5 Hitch System Dimensions ………………………………………………………………..….
47
48
49
50
50
50
51
51
52
53
53
53
56
59
59
60
62
64
64
1
CHAPTER 1. MAIN SPECIFICATIONS OF TRACTOR
General specifications
Tractor Model ET 350 ECONO
Type Frameless, 4WD tractor
Rated draft(kn/kgf) 9.14/932
Dry weight(kg 1450
Min. operation weight(kg) 1565
Wheel tread(mm)
Front wheel 1160
Rear wheel 1100~1400
Radius of turning circle(m)
With one side braked 3.4
Without braking 3.8
Min,ground clearance(mm) 290
Overall dimensions(mm)
Length 3070
Width 1493
Height(to the top of steering wheel) 1540
Theoretical travel speed of tractor(km/h)
1st gear 1.74
2nd gear 2.20
3rd gear 3.58
4th gear 5.68
5th gear 6.83
6th gear 8.63
7th gear 14.04
8th gear 22.27
1st rev. Gear 1.63
2nd rev.Gear 6.38
Engine
Model TY395E
Type Vertical,in-line,water-cooled,four-stroke
Number of cylinders 3
Bore X Stroke(mm) 95/105
2
Tractor Model ET 350 ECONO
Rated speed(r/min) 230
Rated output(kW/hp) 25.7/35
Max.torque(Nm) ≥122.7
Speed at max. torque(r/min) ≤ 1725
Fuel consumption(g/kWh) 245
Oil consumption(g/kWh) ≤ 2.04
Method of lubrication Pressure and splash combined
Method of cooling Closed and forced water circulation
Method of starting Electric starting
Rotating direction(as viewed from the fan) Clockwise
Transmission system
Clutch Dry single-disk constant engagement or
Double Belleville spring interlock controlled
Gear box Straight gear (4+1) X 2
Central drive Spiral bevel gear
Differential Two bevel planetary-gear, closed type
Final drive External exterior engagement, straight gear type
Brake Pedal, mechanical-actuated, closed shoe-type
Running and steering system
Type of drive Rear-wheel drive
Type of front axle Tube with adjustable wheel tread
Specification of tire
Front wheel 6.50-16
Rear wheel 11.2-24
Tire pressure(MPa)
Front wheel 0.23~0.25
Rear wheel 0.10~0.12
Toe-in(mm) 3~11
Camber, front wheel 2°
Kingpin inclination 10°
Kingpin caster 0
Steering gear Worm and roller or BZZ1-80 fully-hydraulic
Ackerman steering Backward of axle
Working facilities
Hydraulic lift
Type Partial separated units
Working depth control Draft and position control combined
3
Tractor Model ET 350 ECONO
Oil pump type CBN316L
Opening pressure of relief Valve(MPa) 13.7
Hydraulic cylinder
Type Horizontal, single-action piston type
Bore(mm) 85
Stroke(mm) 110
Distributor Sliding valve control type
Rated lift capacity(at hitch shaft)(kN) 8.33
Suspension linkage
Type Rear-mounted, three - point ball joint, category I
Upper hitch pin diameter(mm)
Lower hitch pin diameter
Power take-off shaft
Type Non-independent or semi-independent
Dimensions of spline
PTO Speed(r/min) 540,1000
Electrical system
Type 12V, Negative-grounded, single-line system
Alternator JF11(14V,350W) or FWB 15C31
Regulator FT-70 or FT-111
Starting motor QD146
Battery 6-QA-90
Head light 12V upper beam 45W. Lower beam 40W
Tail light 12V 32CP
Multi - indicating panel
Filling capacities(ℓ)
Fuel tank 40
Engine cooling system 7~9
Engine oil sump 4.5
Fuel injection pump 0.3
Hydraulic oil tank 5.7
Chassis 20.8
Hydraulic lift 7
Front drive axle 6
Intermediate Housing 3.5
φ19
φ22.4 +0.33
+0
+0.51
+0.30
8-spline-38 X 29 X 6 or
6-spline-34.79±0.06 X 28.91 ±0.05 X 8.69
+0.032
+0.100
0
-0.28
-0.04
-0.01 -0.040
-0.098
Table des matières
Autres manuels TYM Tracteur
TYM
TYM T743 Manuel utilisateur
TYM
TYM T433 Manuel utilisateur
TYM
TYM T68 Manuel utilisateur
TYM
TYM T603 Manuel utilisateur
TYM
TYM T354 Manuel utilisateur
TYM
TYM T474 Manuel utilisateur
TYM
TYM 5025C Manuel utilisateur
TYM
TYM T264 Manuel d'instructions
TYM
TYM T290 Manuel utilisateur
TYM
TYM 3620 Manuel utilisateur
TYM
TYM TX753 Manuel utilisateur
TYM
TYM T293HST Manuel utilisateur
TYM
TYM T25NH Manuel utilisateur
TYM
TYM TX1500 Manuel utilisateur
TYM
TYM T954 Manuel utilisateur
TYM
TYM 3515C Manuel utilisateur
TYM
TYM T194 Manuel utilisateur
TYM
TYM T264NH Manuel utilisateur
TYM
TYM T454HST Manuel utilisateur
TYM
TYM T1003 Manuel utilisateur
