Tyco Security Products HSM2955 Manuel utilisateur

HSM2955 1.0 Installation Guide

To download the full installation manual and register your product,

visit dsc.com/m/29009400 or scan the QR code to the right.

1. Introduction

This installation manual shall be used in conjunction with the installation manual of the alarm con-

trol panel to which the HSM2955(R) is connected. Disconnect power and telephone line before

installing the module.

1.1 Specifications

Operating Temperature Range -10° to 55°C (14° to 131 °F); UL/ULC: 0° - 49°C

Humidity up to 93% RH, non condensing

Operating Voltage (RED, BLK) from compatible

control panel 11.3 to 12.5 VDC (max)

Current Draw (board only) 100mA (max)

Current Draw (active/max stations) 500mA (max with 2 PC5964E connected);

500mA (max with 4 PC5961E connected)

AUX Output 7.6 - 8.6 VDC/400mA

PC5961E (small audio station) 30mA(min) - 100mA (max)

PC5964E (large audio station) 30mA(min) - 190mA (max)

Wiring Distance (all audio stations) 152m (500ft)

Dimensions 21.7cm x 5.3cm (8.55” x 2.075”)

Microphone Audio Range:

PC5961E 7.62m (25ft)

PC5964E 15.2m (50ft)

Compatibility:

Control Panels HS2016, HS2032, HS2064, HS2128

Communicators TL2803GR, TL2803G, 3G2080R, 3G2080,

3G8080(I), CD8080(I)

1.2 Out of the Box

The HSM2955(R) kit includes the following:

l1 HSM2955(R) Audio Verification Module

l5 Stand-offs

l1 Audio Header Cable

l1 HSM2955(R) Installation Manual

l1 HSM2955(R) User Guide

Figure 1: Installation in the Cabinet

WARNING:HIGH VOLTAGE! Disconnect AC power

and telephone lines prior to servicing.

CAUTION! Do not route wiring over the HSM2955(R)

module. Maintain at least 1” (25.4mm) separation. A min-

imum distance of 1/4”(6.4 mm) must be maintained at

all points between power limited and non-power lim-

ited wiring. All circuits are classified for UL install-

ations as Power Limited/Class II Power Limited,

except for the battery leads which are not power lim-

ited. Do not route any wiring over circuit boards.

2. Installation

2.1 HSM2955(R) Installation

The HSM2955(R) module must be installed by Service Persons only. It must be installed in a metal

cabinet properly grounded. It is the installer’s responsibility to ensure a degree of protection for the

equipment such that no access to the Telecommunications Network Voltage (TNV) circuit is given

to the end user. The metallic cabinet must be secured to the building structure before operation. A

proper ground connection must be provided for the metal cabinet. Internal wiring must be routed

in a manner that prevents:

lexcessive strain on wire and on terminal connections

lloosening of terminal connections

ldamage to conductor insulation

Figure 2: Alarm Control Panel Wiring Diagram (with Communicator)

Figure 3: PCL-422 Wiring Diagram

Figure 4: Alternate Wiring Diagram (Separate Cabinet Configuration)

Figure 5: 3G8080(I)/CD8080(I) Wiring Connections

Figure 6: HSM2955(R) Terminal Connections

Corbus RED

BLK

YEL

GRN

Corbus Power

Corbus Ground

Corbus Com A

Corbus Com B

AUX

Power AUX

COM

Auxiliary Power Output (PTC protected locally).

NOTE: Output current is limited by the available current at the panel

AUX/RED output (refer to the Panel Installation Manual).

Common Ground terminal for station wiring

Tamper TAM HSM2955 Module Tamper Input

Speaker/Mic M1

Microphone #1 (M1) Input Channel

Microphone #2 (M2) Input Channel

Microphone #3 (M3) Input Channel

Microphone #4 (M4) Input Channel

Speakers SPK1

SPK2 Speaker Level Output (supports two DSC Audio Stations)

Speaker Level Output (supports two DSC Audio Stations)

NOTE: SPK1 and SPK2 are parallel wired from a single audio output. Any

combination of audio stations can be used as long as the maximum current

rating is not exceeded:

- 4 small stations (PC5961E)

- 2 large stations (PC5964E)

- 1 large & 2 small stations

Audio AOUT

GND

AIN

Audio Out

Ground

Audio In

NOTE: This is an alternate terminal block. See Figure 4 for use.

Phone Line RNG

TIP

R-1

T-1

Connected to R-1 terminal on the alarm panel

Connected to T-1 terminal on the alarm panel

Connected to house phones

Ground EGND Earth Ground for Telco circuit

3. Privacy

The HSM2955(R) / HSM2955(R) module was designed to adhere to applicable privacy regulations

and only processes data needed for the primary functionality of the device. Before using the mod-

ule you will be asked to provide consent with processing of the personal data that the module may

capture. Note that the module records audio to secure the best functionality of the device. The

recordings are processed securely and automatically erased on a periodic basis. Based on the loc-

ation of the module you may have the obligation to issue a notice about using it. The data recorded

through the HSM2955(R) module are processed and maintained primarily by the data controller.

Data controller is the entity that provides [monitoring] services to you. You have the right to

enquire about your data with them. For more information about their privacy practices please con-

tact the data controller/monitoring service provider. For more details about Tyco privacy practices

please visit our website http://www.tyco.com/privacy. Please refer to Section 7 for a consent form

template. Please note this is only a guideline, contact the data controller regarding their privacy prac-

tices.

4. Consent Form

CONSENT WITH PROVIDING PERSONAL DATA / SENSITIVE PERSONAL DATA

Data Subject1

First name: _____________________ Last name: ______________________________

Residing at: ___________________________________________________ I hereby grant an informed con-

sent to allow _______________________________ and its affiliates (hereinafter the “Company”) to pro-

cess my personal data [ ]2/ sensitive personal data [ ] 3for the purpose specified below. I also

consent to the data being transferred to third parties and abroad, if that is necessary for the Com-

pany to fulfill the purpose of data collection as described below, in accordance with applicable

data privacy laws.

Personal Data collected: __________________________ (include specific data fields)

Sensitive Personal Data collected: __________________ (include specific data fields)

The data is collected for the purpose of ________________________________________________________

_____________________________________________________________________________________________

_______ (describe in reasonable detail)

I have been informed about my rights related to the processing of personal data and about other

conditions related to the processing of personal data and to the method of its processing and

accessing. I certify that all the personal data is accurate and true and provided voluntarily. I have

been informed about my right to access and check my personal data processed by the Company

upon request sent to ____________________________________________________. I am aware I can with-

draw this consent in writing at any time.

CONTENT AND PURPOSE OF THIS CONSENT EXPLAINED BY

Full name: _____________________________________________________________

Signature: ______________________________________________________________

Contact detail: __________________________________________________________

To learn more about the Data Controller’s privacy practices visit/email:

Date: ________________________________

Data subject signature: ____________________________

1Data Subject is the person to whom the personal data relates to.

2Personal data is any information relating to an identified or identifiable individual, such as name, email or other addresses, phone

number, ID numbers, employment data (such as salary or evaluations), mother’s maiden name, credit card number or credit inform-

ation etc.

3Sensitive personal data is personal data consisting of information as to the racial or ethnic origin of the individual, their political

opinions, religious beliefs, physical or mental health or condition, sexual life etc.

Limited Warranty

DigitalSecurity Controls(DSC) warrantsthat fora periodof 12months fromthe date of

purchase, the product shall befree of defects inmaterials andworkmanship under normal

useandthat in fulfilment of any breachof suchwarranty, DSC shall, at its option, repair or

replacethedefective equipment uponreturn of theequipment toitsrepair depot. This war-

ranty appliesonly todefects inparts andworkmanship andnot todamage incurredin ship-

pingor handling, or damage due to causesbeyond the control of DSC such as lightning,

excessivevoltage, mechanicalshock, waterdamage, or damagearisingout of abuse, alter-

ationorimproper applicationof theequipment. Theforegoingwarrantyshallapply onlyto the

originalbuyer, andisandshallbeinlieuof any andallotherwarranties, whetherexpressed or

impliedandof allotherobligations orliabilitieson thepartof DSC. DigitalSecurity Controls

neitherassumes responsibilityfor, norauthorizes anyother personpurporting toact on its

behalftomodifyor tochangethis warranty,nortoassume foritany otherwarranty or liab-

ility concerning thisproduct. Inno event shall DSC beliable forany direct, indirect or con-

sequentialdamages, loss of anticipatedprofits, loss of time orany other lossesincurred by

thebuyerinconnection withthepurchase, installationoroperationor failureof this product.

WARNING: DSC recommends that the entiresystembe completelytested ona regular

basis. However, despitefrequent testing, anddue to, but not limitedto, criminal tampering

or electricaldisruption, it ispossibleforthisproduct tofailtoperformas expected. Important

Information: Changes/modifications not expresslyapproved byDSC could voidthe user’s

authoritytooperatethisequipment.

IMPORTANT - READ CAREFULLY: DSC Software purchased with or without

Products and Components is copyrighted and is purchased under the following license

terms: This End-UserLicenseAgreement (“EULA”) isalegalagreement betweenYou (the

company, individual or entity who acquired theSoftware and any related Hardware) and

DigitalSecurity Controls, a division of TycoSafety Products Canada Ltd. (“DSC”), the

manufacturerof theintegratedsecurity systemsand thedeveloperof thesoftwareand any

relatedproducts orcomponents (“HARDWARE”)which Youacquired. If the DSC soft-

wareproduct (“SOFTWAREPRODUCT” or“SOFTWARE”) isintended tobe accom-

paniedbyHARDWARE, andisNOT accompaniedbynew HARDWARE, Youmay not

use, copy or install the SOFTWARE PRODUCT. The SOFTWARE PRODUCT

includes computer software, and may include associated media, printed materials, and

“online”orelectronicdocumentation.

IMPORTANT READ CAREFULLY: DSC Software purchased with or without

Products and Components is copyrighted and is purchased under the following license

terms:

ThisEndUser LicenseAgreement ("EULA")is alegal agreement between You(the com-

pany, individualorentity whoacquiredthe Softwareandany relatedHardware) and Digital

Security Controls, a division of Tyco Safety Products Canada Ltd. ("DSC"), the man-

ufacturer of the integrated security systems and the developer of the software and any

relatedproductsorcomponents ("HARDWARE")whichYouacquired.

If the DSC software product ("SOFTWAREPRODUCT" or"SOFTWARE") is inten-

ded to be accompanied by HARDWARE, and is NOT accompanied by new

HARDWARE, You may not use, copy or install the SOFTWARE PRODUCT. The

SOFTWARE PRODUCT includes computer software, and may include associated

media, printedmaterials, and"online"or electronic documentation.

Anysoftwareprovidedalongwiththe SOFTWARE PRODUCT that isassociatedwith a

separateenduser licenseagreement islicensedtoYouunderthetermsof that licenseagree-

ment.

By installing, copying, downloading, storing, accessing or otherwise using the

SOFTWARE PRODUCT, You agree unconditionally to be bound by the terms of this

EULA, evenif this EULAisdeemedtobeamodificationof anyprevious arrangement or con-

tract. If You do not agree to the terms of this EULA, DSC is unwilling to license the

SOFTWARE PRODUCT toYou, andYouhavenoright touseit.

SOFTWARE PRODUCT LICENSE

TheSOFTWARE PRODUCT is protected by copyright laws andinternational copyright

treaties, as well as other intellectual property laws and treaties. The SOFTWARE

PRODUCT is licensed, not sold.

1. GRANT OF LICENSE. ThisEULAgrants Youthefollowingrights:

(a)Software Installationand Use - For eachlicense You acquire, You mayhave only one

copyof theSOFTWAREPRODUCT installed.

(b) Storage/Network Use - The SOFTWARE PRODUCT may not be installed,

accessed, displayed, run, shared or used concurrently on or from different computers,

includingaworkstation, terminalor other digitalelectronicdevice("Device"). Inother words,

if You have severalworkstations, You will haveto acquire alicense for each workstation

wheretheSOFTWAREwillbeused.

(c)Backup Copy - Youmay makeback upcopies of the SOFTWARE PRODUCT, but

Youmay onlyhaveonecopyper licenseinstalledat anygiventime. Youmay usetheback up

copysolelyfor archival purposes. Except as expressly providedinthis EULA, Youmay not

otherwisemake copiesof the SOFTWAREPRODUCT, includingthe printed materials

accompanyingtheSOFTWARE.

2. DESCRIPTION OF OTHER RIGHTS AND LIMITATIONS

(a) Limitations on Reverse Engineering, Decompilation and Disassembly - You may not

reverseengineer, decompile, or disassemblethe SOFTWAREPRODUCT, except and

only totheextent that suchactivity isexpresslypermittedbyapplicablelaw notwithstanding

thislimitation. Youmaynot makeanychangesor modificationstotheSoftware, without the

written permission of an officer of DSC. You may not remove any proprietary notices,

marks or labels from the Software Product. You shall institute reasonable measures to

ensurecompliancewiththetermsandconditionsof this EULA.

(b) Separation of Components - The SOFTWARE PRODUCT is licensed as a single

product. Its component parts may not be separated for use on more than one

HARDWAREunit.

HARDWARE, then the SOFTWAREPRODUCT is licensedwith the HARDWARE

asa single integrated product. In this case, theSOFTWARE PRODUCT may only be

usedwiththeHARDWAREasset forthinthis EULA.

(d)Rental- Youmay not rent, lease or lend theSOFTWARE PRODUCT. Youmay not

makeit availabletoothersor post it onaserver orwebsite.

(e)SoftwareProduct Transfer- Youmay transfer allof Your rightsunderthis EULAonly as

part of apermanent saleor transfer of the HARDWARE, provided Youretain no copies,

Youtransferallof theSOFTWAREPRODUCT (includingallcomponent parts, the media

andprintedmaterials, anyupgrades andthisEULA), andprovidedtherecipient agreestothe

termsof this EULA. If the SOFTWAREPRODUCT is anupgrade, any transfer must

alsoincludeallprior versions of theSOFTWARE PRODUCT.

(f) Termination - Without prejudice to any otherrights, DSC mayterminate this EULA if

Youfailtocomplywiththetermsandconditions of thisEULA. Insuchevent, Youmust des-

troyallcopiesof theSOFTWARE PRODUCT andallof its component parts.

(g)Trademarks - ThisEULA does not grant You anyrights in connectionwith any trade-

marks orservicemarksof DSC oritssuppliers.

3. COPYRIGHT

AlltitleandintellectualpropertyrightsinandtotheSOFTWARE PRODUCT (includingbut

not limited to any images, photographs, and text incorporated into the SOFTWARE

PRODUCT), the accompanying printed materials, andany copies of the SOFTWARE

PRODUCT, areowned byDSC orits suppliers.Youmay notcopy theprinted materials

accompanyingtheSOFTWARE PRODUCT. Alltitleandintellectualpropertyrights inand

tothecontent whichmaybe accessedthrough useof the SOFTWARE PRODUCT are

thepropertyof therespectivecontent ownerand maybeprotected byapplicable copyright

or other intellectualpropertylaws andtreaties. ThisEULAgrants Younorightstouse such

content. Allrightsnot expresslygrantedunder this EULAarereservedbyDSC andits sup-

pliers.

4. EXPORT RESTRICTIONS

Youagreethat Youwillnot export or reexport theSOFTWAREPRODUCT toany coun-

try, person, orentity subject toCanadianexport restrictions.

5. CHOICE OF LAW: ThisSoftware LicenseAgreement is governed by the laws of the

Provinceof Ontario, Canada.

6. ARBITRATION

AlldisputesarisinginconnectionwiththisAgreement shallbedeterminedbyfinaland binding

arbitrationinaccordance withthe ArbitrationAct, andthe partiesagree tobe boundby the

arbitrator'sdecision. Theplace of arbitrationshall beToronto, Canada, andthelanguage of

thearbitrationshallbeEnglish.

7. LIMITED WARRANTY

(a) NO WARRANTY

DSC PROVIDES THE SOFTWARE "AS IS" WITHOUT WARRANTY. DSC

DOES NOT WARRANT THAT THE SOFTWARE WILL MEET YOUR

REQUIREMENTS OR THAT OPERATION OF THE SOFTWARE WILL BE

UNINTERRUPTED OR ERROR-FREE.

(b) CHANGES IN OPERATIN G ENVIRONMENT

DSC shall not be responsible for problems caused by changes in the operating char-

acteristicsof the HARDWARE, or for problems in the interaction of the SOFTWARE

PRODUCT withnon-DSC-SOFTWARE orHARDWAREPRODUCTS.

(c)LIMITATION OF LIABILITY; WARRANTY REFLECTSALLOCATION OF RISK

IN ANY EVENT, IF ANYSTATUTE IMPLIESWARRANTIES OR CONDITIONS

NOT STATED IN THIS LICENSE AGREEMENT, DSC'S ENTIRE LIABILITY

UNDER ANY PROVISION OF THIS LICENSE AGREEMENT SHALL BE

LIMITED TO THEGREATER OF THEAMOUNT ACTUALLY PAID BY YOU TO

LICENSE THE SOFTWARE PRODUCT AND FIVE CANADIAN DOLLARS

(CAD$5.00). BECAUSE SOME JURISDICTIONS DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF LIABILITY FOR CONSEQUENTIAL OR

INCIDENTALDAMAGES, THE ABOVE LIMITATION MAYNOT APPLYTO YOU.

(d) DISCLAIMER OF WARRANTIES

THISWARRANTY CONTAINS THE ENTIREWARRANTY AND SHALL BE IN

LIEU OF ANY AND ALL OTHER WARRANTIES, WHETHER EXPRESSED OR

IMPLIED (INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY

OR FITNESS FOR A PARTICULAR PURPOSE) AND OF ALL OTHER

OBLIGATIONS OR LIABILITIES ON THE PART OF DSC. DSC MAKES NO

OTHER WARRANTIES. DSC NEITHER ASSUMES NOR AUTHORIZES ANY

OTHER PERSON PURPORTING TO ACT ON ITS BEHALF TO MODIFYOR TO

CHANGE THIS WARRANTY, NOR TO ASSUME FOR IT ANY OTHER

WARRANTY OR LIABILITY CONCERNING THISSOFTWAREPRODUCT.

(e) EXCLUSIVEREMEDYAND LIMITATION OF WARRANTY

UNDER NO CIRCUMSTANCES SHALL DSC BE LIABLE FOR ANY SPECIAL,

INCIDENTAL, CONSEQUENTIAL OR INDIRECT DAMAGES BASED UPON

BREACH OF WARRANTY, BREACH OF CONTRACT, NEGLIGENCE,

STRICT LIABILITY, OR ANY OTHER LEGAL THEORY. SUCH DAMAGES

INCLUDE, BUT ARE NOT LIMITED TO, LOSS OF PROFITS, LOSS OF THE

SOFTWARE PRODUCT OR ANY ASSOCIATED EQUIPMENT, COST OF

CAPITAL, COST OF SUBSTITUTE OR REPLACEMENT EQUIPMENT,

FACILITIESOR SERVICES, DOWN TIME, PURCHASERS TIME, THE CLAIMS

OaF THIRD PARTIES, INCLUDING CUSTOMERS, AND INJURY TO

PROPERTY.

WARNING: DSC recommends that the entiresystembe completelytested ona regular

basis. However, despitefrequent testing, anddue to, but not limitedto, criminal tampering

or electricaldisruption, it is possiblefor thisSOFTWAREPRODUCT tofailtoperform as

expected.

Toronto, Canada • www.dsc.com

Tech Support: 1-800-387-3630 (Canada & U.S.) or 905-760-3000

The trademarks, logos, and service marks displayed on this document are registered in the United States [or other

countries]. Any misuse of the trademarks is strictly prohibited and Tyco will aggressively enforce its intellectual

property rights to the fullest extent of the law, including pursuit of criminal prosecution wherever necessary. All

trademarks not owned by Tyco are the property of their respective owners, and are used with permission or

allowed under applicable laws. Product offerings and specifications are subject to change without notice. Actual

products may vary from photos. Not all products include all features. Availability varies by region; contact your

sales representative.

FCC STATEMENT

CAUTION: Changesormodificationsnot expresslyapprovedbyDigitalSecurity Controls

couldvoidyourauthority tousethisequipment.

Thisequipment has been tested andfound to comply with thelimits for a Class B digital

device, pursuant toPart 15of theFCC Rules. These limitsare designedto provide reas-

onableprotection against harmful interference in a residential installation. This equipment

generates, uses and can radiate radio frequency energy and, if not installed and used in

accordancewiththeinstructions, maycauseharmfulinterferencetoradiocommunications.

However, thereisno guaranteethat interference willnot occurin aparticular installation. If

thisequipment doescauseharmfulinterferencetoradioor televisionreception, whichcanbe

determinedbyturningthe equipment off andon, theuseris encouraged totrytocorrect the

interferencebyoneormoreof thefollowingmeasures:

- Re-orient thereceivingantenna.

- Increasetheseparationbetweentheequipment andreceiver.

- Connect theequipment intoanoutlet onacircuit different fromthat towhichthereceiver is

connected.

- Consult dealeror experiencedradio/televisiontechnicianfor help.

Theusermay findthe followingbookletprepared bythe FCC useful: ’How toIdentify and

ResolveRadio/Television InterferenceProblems’. This booklet is availablefrom the U.S.

Government PrintingOffice, WashingtonD.C. 20402, Stock #004-000-00345-4.

IMPORTANT INFORMATION

Thisequipment complies withPart 68 of theFCC Rulesandthe requirements adopted by

theACTA. Onthesideof thisequipment isalabelthat contains, amongotherinformation, a

product identifier inthe format US:AAAEQ##TXXXX. If requested, thisnumber must be

providedtotheTelephoneCompany.

Product identifier: US: F53MO01BHSM2955

USOC Jack: RJ-31X

TelephoneConnectionRequirements

Aplug and jackused to connect this equipment tothe premises wiringand telephone net-

workmust complywith theapplicableFCC Part 68rules and requirements adoptedby the

ACTA. A compliant telephone cord and modular plug is provided with this product. It is

designedtobeconnectedtoacompatiblemodularjack that isalsocompliant. Seeinstallation

instructionsfordetails.

RingerEquivalenceNumber(REN)

TheREN isusedtodeterminethenumber of devices that maybeconnectedtoa telephone

line. ExcessiveRENsonatelephonelinemay result inthedevicesnot ringinginresponse to

anincomingcall. Inmost but not allareas, thesumof RENs shouldnot exceedfive(5.0). To

becertain of the numberof devicesthat maybe connectedto aline, asdetermined by the

totalRENs, contact the localTelephone Company. For products approvedafter July 23,

2001, theREN forthis product ispart of theproduct identifierthat hastheformat

US: AAAEQ##TXXXX. Thedigitsrepresented by ##arethe REN without adecimal point

(e.g., 03isaREN of 0.3). Forearlierproducts, theREN isseparatelyshownonthelabel.

Incidenceof Harm

If thisequipment HSM2955causes harmtothetelephonenetwork, thetelephone company

willnotify youin advancethat temporarydiscontinuance of service maybe required. But if

advancenoticeisnot practical, theTelephone Companywillnotify thecustomeras soon as

possible. Also, youwillbeadvisedof your right tofileacomplaint withtheFCC if you believe

it isnecessary.

Changes inTelephoneCompanyEquipment or Facilities

TheTelephoneCompany may makechanges inits facilities, equipment, operationsor pro-

cedures that could affect the operation of the equipment. If this happens the Telephone

Companywill provideadvance notice inorder foryou to makenecessary modifications to

maintainuninterruptedservice.

Equipment MaintenanceFacility

If troubleisexperienced withthisequipment HSM2955, contact thefacility indicated below

forrepair or warranty information. If the equipment is causing harmto the telephone net-

work,the Telephone Company may request thatyou disconnect the equipment until the

problemissolved. Thisequipmentis ofa typethatis not intended toberepaired bythe end

user. DSC c/oAPLLogistics, 757DouglasHillRd., LithiaSprings, GA30122, USA

AdditionalInformation

Connectionto party line serviceis subject to state tariffs. Contact the state public utility

commission, publicservicecommissionorcorporationcommissionfor information.

Alarmdialingequipment must beable toseizethe telephonelineand placeacall inan emer-

gencysituation. It must beabletodothisevenif otherequipment (telephone, answeringsys-

tem, computer modem, etc.) alreadyhas thetelephone linein use. To doso, alarm dialing

equipment must beconnectedtoaproperlyinstalled RJ-31Xjack that iselectrically in series

withandaheadof allotherequipment attachedtothesametelephoneline. Proper installation

is depictedinthefigure below. If youhaveany questions concerningtheseinstructions, you

shouldconsult your telephone company ora qualified installer about installingthe RJ-31X

jackandalarmdialingequipment foryou.

IC: 160A-HSM2955

CAN ICES-3(B)/NMB-3(B)

NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment

TechnicalSpecifications. This is confirmed bythe registration number. The abbreviation,

IC, before the registration number signifies that registration was performed based on a

Declaration of Conformity indicating that Industry Canada technical specifications were

met. It doesnot implythat IndustryCanadaapprovedtheequipment.

NOTICE: TheRingerEquivalence Number(REN) for this terminalequipment is0.1. The

REN assignedtoeachterminalequipment provides anindicationof themaximumnumberof

terminalsallowedtobe connectedtoa telephoneinterface.The terminationonan interface

mayconsist of anycombination of devices subject only tothe requirement that thesum of

theRingerEquivalenceNumbersof allthedevices doesnot exceed5.

AVIS: Le présent matériel est conforme aux spécifications techniques d’Industrie Canada

applicables au matériel terminal. Cette conformité est confirmée par le numéro d'en-

registrement. Le sigle IC, placé devant le numéro d'enregistrement, signifie que l’en-

registrement s’est effectuéconformément àunedéclarationdeconformitéet indiquequeles

spécifications techniques d'Industrie Canada ont été respectées. Il n’implique pas qu’In-

dustrieCanadaaapprouvélematériel.

AVIS : L'indice d'équivalence de la sonnerie (IES) du présent matériel est de 0.1. L'IES

assignéàchaquedispositif terminalindiquelenombremaximaldeterminauxquipeuvent être

raccordés àuneinterfacetéléphonique. Laterminaisond'uneinterfacepeut consisteren une

combinaisonquelconque de dispositifs, àla seule condition quela somme d'indices d'équi-

valencedelasonneriedetouslesdispositifs n'excèdepas5.

HSM2955 1.0 Manuel d’installation

Pour télécharger le manuel d'installation complète et enregistrer votre pro-

duit, visitez dsc.com/m/29009401 ou scannez le code QR pour le droit.

1. Introduction

Ce manuel d’installation doit être utilisé conjointement au manuel d’installation de la centrale à

laquelle le module HSM2955(R) est connecté. Débranchez l’alimentation et la ligne téléphonique

avant d’installer le module.

1.1 Spécifications

Plage de température de fonctionnement de -10 à 55°C (de 14 à 131°F); UL/ULC: de 0 à

49°C

Humidité jusqu’à 93% d’humidité relative, sans conden-

sation

Tension de fonctionnement (ROUGE, NOIR)

depuis une centrale compatible 11.3 à 12.5 VDC (max)

Intensité de courant absorbé (carte uniquement) 100mA (max)

Intensité de courant absorbé (nb. de stations

max. connectées/actives) 500mA (max avec 2 modules PC5964E connectés)

500mA (max avec 4 modules PC5961E connectés)

Sortie auxiliaire de 7,6 à 8,6VCC/400 mA

PC5961E (petite station audio) de 30mA (min) à 100mA (max)

PC5964E (grande station audio) de 30mA (min) à 190mA (max)

Longueur de câble (toutes les stations audio) 152m (500pieds)

Dimensions 21,7cm x 5,3cm (8,55” x 2,075”)

Portée audio du microphone :

PC5961E 7,62m (25pieds)

PC5964E 15,2m (50pieds)

Compatibilité :

Centrales HS2016, HS2032, HS2064, HS2128

Communicateurs TL2803GR, TL2803G, 3G2080R, 3G2080,

3G8080(I), CD8080(I)

1.2 Déballage

Le kit HSM2955(R) comprend les articles suivants:

l1 module de vérification audio HSM2955(R)

l5 pitons de montages

l1 câble avec connecteur audio

l1 manuel d’installation HSM2955(R)

l1 guide d’utilisation HSM2955(R)

Figure 1: Installation dans l’armoire

AVERTISSEMENT :HAUTE TENSION! Débranchez

l'alimentation secteur et les lignes téléphoniques avant

les interventions.

ATTENTION ! Ne pas acheminer le câblage au-dessus

du module HSM2955 (R). Garder un espace de sépa-

ration d’au moins 25,4mm (1”). Un espace de sépa-

ration de 6,4mm (1/4”) minimum doit être respecté à

tous les points entre le câblage à puissance limitée et

non limitée. Tous les circuits sont classés pour les ins-

tallations UL comme à puissance limitée/puissance limi-

tée de classe II, à l’exception des conducteurs de la

batterie qui ne sont pas à puissance limitée. Ne pas faire

passer des câbles au- dessus de la carte de circuit

imprimé.

2. Installation

2.1 Installation du module HSM2955(R)

Le module HSM2955(R) doit être installé exclusivement par une personne qualifiée. Il doit être ins-

tallé dans une armoire métallique correctement mise à la terre. Il est de la responsabilité de l’ins-

tallateur de garantir un degré de protection de l’équipement de telle façon qu’aucun accès au circuit

sous tension du réseau de télécommunication (TNV) ne soit possible par l’utilisateur. L’armoire

métallique doit être fixée à une paroi du bâtiment avant utilisation. Une mise à la terre correcte doit

être réalisée sur l’armoire métallique. Le câblage interne doit être acheminé de façon à éviter:

ldes contraintes excessives sur les câbles et les bornes de connexion

lle desserrage des bornes de connexion

ldes détériorations de l’isolant du conducteur

Figure 2: Schéma de câblage de la centrale d’alarme (avec communicateur)

Table des matières

Langues :

Autres manuels Tyco Security Products Unité de contrôle

Tyco Security Products

Tyco Security Products Software House PSX-M8 Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur