TYAN GN70-B7056 Guide de démarrage rapide

http://www.tyan.com

GN70-B7056

Service Engineer’s Manual

http://www.tyan.com

PREFACE

This publication, including all photographs, illustrations, and software, is

Neither this manual, nor any material contained herein, may be reproduced

without written consent of manufacturer.

a registered trademark of MiTAC International Corporation.

Version 1.0

Disclaimer

Information contained in this document is furnished by MiTAC International

Corporation and has been reviewed for accuracy and reliability prior to printing.

MiTAC assumes no liability whatsoever, and disclaims any express or implied

warranty, relating to sale and/or use of TYAN®products including liability or

warranties relating to fitness for a particular purpose or merchantability. MiTAC

retains the right to make changes to produce descriptions and/or specifications

at any time, without notice. In no event will MiTAC be held liable for any direct

or indirect, incidental or consequential damage, loss of use, loss of data or

other malady resulting from errors or inaccuracies of information contained in

this document.

Trademark Recognition

All registered and unregistered trademarks and company names contained in

this manual are property of their respective owners including, but not limited to

the following.

TYAN®is a trademark of MiTAC International Corporation.

Intel®is a trademark of Intel®Corporation.

AMI®, AMIBIOS® and combinations thereof are trademarks of AMI

Technologies.

Microsoft®, Windows®are trademarks of Microsoft Corporation.

IBM®, PC®, AT®and PS/2®are trademarks of IBM Corporation.

Winbond®is a trademark of Winbond Electronics Corporation.

http://www.tyan.com

FCC Declaration

Notice for the USA

Compliance Information Statement (Declaration of

Conformity Procedure) DoC FCC Part 15: This

device complies with part 15 of the FCC Rules

This device complies with Part 15 of the FCC Rules. Operation is subject to

the following conditions:

zThis device must not cause harmful interference.

zThis device must accept any interference received, including

interference that may cause undesirable operation.

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC Rules. These limits

are designed to provide reasonable protection against harmful interference

when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if

not installed and used in accordance with the instruction manual, may cause

harmful interference to radio communications. Operation of this equipment

in a residential area is likely to cause harmful interference in which case the

user will be required to correct the interference at his own expense.

Notice for Canada

This Class A digital apparatus complies with Canadian ICES-003. Cet

appareil numérique de la Classe A est conforme à la norme NMB-003 du

Canada.

Notice for Europe (CE Mark)

This product is in conformity with the Council

Directive 2004/108/EC.

CAUTION: Lithium battery included with this board. Do not puncture,

mutilate, or dispose of battery in fire. There will be danger of explosion if

battery is incorrectly replaced. Replace only with the same or equivalent

type recommended by manufacturer. Dispose of used battery according to

manufacturer instructions and in accordance with your local regulations.

http://www.tyan.com

About this Manual

This manual provides you with instructions on installing your TYAN

GN70-B7056. This Manual is intended for experienced users and

integrators with hardware knowledge of personal computers.

This manual consists of the following parts:

Chapter1: Provides an introduction to the TYAN GN70-B7056

barebones, standard parts list, describes the external

components, gives a table of key components, and

provides block diagram of the system.

Chapter2: Covers procedures on installing the processor, memory

modules and hard drives.

Chapter3: Covers the removal and replacement procedures for

pre-installed components.

Appendix: List the cable connection and FRU part tables for reference

of system setup, and technical support in case a problem

arises with your system.

http://www.tyan.com

Safety and Compliance Information

Before installing and using TYAN GN70-B7056, take note of the following

precautions:



gRead all instructions carefully.

gDo not place the unit on an unstable surface, cart, or stand.

gDo not block the slots and opening on the unit, which are provided for

ventilation.

gOnly use the power source indicated on the marking label. If you are not

sure, contact the power company.

gThe unit uses a three-wire ground cable, which is equipped with a third pin to

ground the unit and prevent electric shock. Do not defeat the purpose of this

pin. If your outlet does not support this kind of plug, contact your electrician

to replace your obsolete outlet.

gDo not place anything on the power cord. Place the power cord where it will

not be in the way of foot traffic.

gFollow all warnings and cautions in this manual and on the unit case.

gDo not push objects in the ventilation slots as they may touch high voltage

components and result in shock and damage to the components.

gWhen replacing parts, ensure that you use parts specified by the

manufacturer.

gWhen service or repairs have been done, perform routine safety checks

to verify that the system is operating correctly.

gAvoid using the system near water, in direct sunlight, or near a heating

device.

gCover the unit when not in use.

http://www.tyan.com

Safety Information

Retain and follow all product safety and operating instructions provided

with your equipment. In the event of a conflict between the instructions in

this guide and the instructions in equipment documentation, follow the

guidelines in the equipment documentation.

Observe all warnings on the product and in the operating instructions. To

reduce the risk of bodily injury, electric shock, fire and damage to the

equipment, observe all precautions included in this guide.

You must become familiar with the safety information in this guide before

you install, operate, or service TYAN products.

Symbols on Equipment

Caution. This symbol indicates a potential

hazard. The potential for injury exists if

cautions are not observed. Consult equipment

documentation for specific details.

Warning. This symbol indicates the presence

of hazardous energy circuits or electric shock

hazards. Refer all servicing to qualified

personnel.

Warning. This symbol indicates the presence of a

hot surface or hot component. If this surface is

contacted, the potential for injury exists.

To reduce risk of injury from a hot component,

allow the surface to cool before touching.

General Precautions

gFollow all caution and warning instructions marked on the equipment and

explained in the accompanying equipment documentation.



Machine Room Environment

 gMake sure that the area in which you install the system is properly

ventilated and climate-controlled.

http://www.tyan.com

gEnsure that the voltage and frequency of your power source match the

voltage and frequency inscribed on the electrical rating label of the

equipment.

gDo not install the system in or near a plenum, air duct, radiator, or heat

gNever use the product in a wet location.

Equipment Chassis

gDo not block or cover the openings to the system.

gNever push objects of any kind through openings in the equipment.

Dangerous voltages might be present.

gConductive foreign objects can produce a short circuit and cause fire,

electric shock, or damage to your equipment.

gLift equipment using both hands and with your knees bent.

Equipment Racks

To avoid injury or damage to the equipment:

gObserve local occupational health and safety requirements and guidelines

for manual materials handling.

gDo not attempt to move a rack by yourself; a minimum of two people are

needed to move a rack.

gDo not attempt to move a fully loaded rack. Remove equipment from the

rack before moving it.

gDo not attempt to move a rack on an incline that is greater than 10 degrees

from the horizontal.

gMake sure the rack is properly secured to the floor or ceiling.

gMake sure the stabilizing feet are attached to the rack if it is a single-rack

installation.

gMake sure racks are coupled together if it is a multiple-rack installation.

gMake sure the rack is level and stable before installing an appliance in the

rack.

gMake sure the leveling jacks are extended to the floor.

http://www.tyan.com

gMake sure the full weight of the rack rests on the leveling jacks.

gAlways load the rack from the bottom up. Load the heaviest component in

the rack first.

gMake sure the rack is level and stable before pulling a component out of the

rack.

gMake sure only one component is extended at a time. A rack might become

unstable if more than one component is extended.

To avoid damage to the equipment:

gThe rack width and depth must allow for proper serviceability and cable

management.

gEnsure that there is adequate airflow in the rack. Improper installation or

restricted airflow can damage the equipment.

gThe rack cannot have solid or restricted airflow doors. You must use a

mesh door on the front and back of the rack or remove the doors to ensure

adequate air flow to the system.

gIf you install the Model in a rack, do not place equipment on top of the unit.

It will cause restricted airflow and might cause damage to the equipment.

gMake sure the product is properly matted with the rails. Products that are

improperly matted with the rails might be unstable.

gVerify that the AC power supply branch circuit that provides power to the

rack is not overloaded. This will reduce the risk of personal injury, fire, or

damage to the equipment. The total rack load should not exceed 80 percent

of the branch circuit rating. Consult the electrical authority having jurisdiction

over your facility wiring and installation requirements.

Equipment Power Cords

gUse only the power cords and power supply units provided with your

system. The system might have one or more power cords.

gPlug the power cord into a grounded (earthed) electrical outlet that is easily

accessible at all times.

gIn all European electrical environments, you must ground the Green/Yellow

tab on the power cord. If you do not ground the Green/Yellow tab, it can

cause an electrical shock due to high leakage currents.

Do not place objects on AC power cords or cables. Arrange them so that no

http://www.tyan.com

one might accidentally step on or trip over them.

gDo not pull on a cord or cable. When unplugging from the electrical outlet,

grasp the cord by the plug.

gҏTo reduce the risk of electrical shock, disconnect all power cords before

servicing the appliance.

Equipment Batteries

gThe system battery contains lithium manganese dioxide. If the battery pack

is not handled properly, there is risk of fire and burns.

gDo not disassemble, crush, puncture, short external contacts, or dispose of

the battery in fire or water.

gDo not expose the battery to temperatures higher than 60°C (140°F).

gThe system battery is not replaceable. If the battery is replaced by an

incorrect type, there is danger of explosion. Replace the battery only with a

spare designated for your product.

gDo not attempt to recharge the battery.

gDispose of used batteries according to the instructions of the manufacturer.

Do not dispose of batteries with the general household waste. To forward

them to recycling or proper disposal, use the public collection system or return

them to TYAN, your authorized TYAN partner, or their agents.

Equipment Modifications

gDo not make mechanical modifications to the system. TYAN is not

responsible for the regulatory compliance of TYAN equipment that has been

modified.

Equipment Repairs and Servicing

gThe installation of internal options and routine maintenance and service of

this product should be performed by individuals who are knowledgeable about

the procedures, precautions, and hazards associated with equipment

containing hazardous energy levels.

gDo not exceed the level of repair specified in the procedures in the product

documentation. Improper repairs can create a safety hazard.

gAllow the product to cool before removing covers and touching internal

Table des matières

Autres manuels TYAN Serveur

TYAN

TYAN Transport GX21 B2735 Manuel utilisateur

TYAN

TYAN TA70-B8237 Manuel utilisateur

TYAN

TYAN Tank GT20 B5372-LH Manuel utilisateur

TYAN

TYAN Transport TA26 B3992 Manuel utilisateur

TYAN

TYAN GT20 (B5502) Manuel utilisateur

TYAN

TYAN Tank GT14 B5372-LC Manuel utilisateur

TYAN

TYAN TN76-BP016 Manuel utilisateur

TYAN

TYAN Transport GT28 B2935 Manuel utilisateur

TYAN

TYAN TA77-B7061 Guide de démarrage rapide

TYAN

TYAN YR188-B537M Manuel utilisateur

TYAN

TYAN B8226 Guide de démarrage rapide

TYAN

TYAN Tank FT48 B5382 Manuel utilisateur

TYAN

TYAN GT62H-B7106 Guide de démarrage rapide

TYAN

TYAN TN76A-B8242 Guide de démarrage rapide

TYAN

TYAN GC68A-B7136 Guide de démarrage rapide

TYAN

TYAN GT24-B8226 Manuel utilisateur

TYAN

TYAN Transport GX28 B2882 Manuel utilisateur

TYAN

TYAN FT77A-B7059 Guide de démarrage rapide

TYAN

TYAN TS65-B7126 Guide de démarrage rapide

TYAN

TYAN Thunder n3600QE S4980 Manuel utilisateur

TYAN

TYAN Transport GS10 B2094T15 Manuel utilisateur

TYAN

TYAN TN70A-B8026 Guide de démarrage rapide

TYAN

TYAN B7086T70BV12HR Guide de démarrage rapide

TYAN

TYAN FT48-B8812 Guide de démarrage rapide

Manuels Serveur populaires d'autres marques

HP AlphaServer ES47 Manuel utilisateur

Dell

Dell PowerEdge R410 Manuel utilisateur

PowerNAS

PowerNAS CMA Manuel utilisateur

Supero

Supero FatTwin F617R3-FT Manuel utilisateur

MSI

MSI P1-109N-L70 Manuel utilisateur

Dell

Dell PowerEdge XE9640 Manuel

Dell

Dell PS4100 Instructions de montage

EtroVISION

EtroVISION EV3151 Manuel utilisateur

NEC

NEC Express5800/T110j Manuel utilisateur

HP ProLiant Gen9 Manuel utilisateur

Compaq

Compaq ProLiant 3000 Manuel

Dell

Dell PowerEdge 3YPMN Manuel utilisateur

iRobo

iRobo IPC2U Manuel utilisateur

Nortel

Nortel 1000 Con?guration guide Manuel utilisateur

Asus

Asus AP7500 Manuel d'utilisation et d'entretien

Avid Technology

Avid Technology AirSpeed 5000 Manuel utilisateur

HP Integrity rx2600 Guide d'installation

Milestone

Milestone Husky IVO 350T Manuel utilisateur