TYAN THUNDER I7500 Manuel utilisateur

http://www.TYAN.com

Thunder i7500 ///

S2720

Revision 1.01

may be reproduced or translated without prior written consent from TYAN Computer Corp.

All registered and unregistered trademarks and company names contained in this manual are

property of their respective owners including, but not limited to the following.

TYAN, Thunder i7500 S2720 are trademarks of TYAN Computer Corporation.

Intel, Xeon, and combinations thereof are trademarks of Intel Corporation.

AMI, AMIBIOS are trademarks ofAMI Software Inc.

Microsoft, Windows are trademarks of Microsoft Corporation.

IBM, PC, AT, PS/2 are trademarks of IBM Corporation.

Winbond is a trademark of Winbond Electronics Corporation.

Portable Document Format (PDF) is a trademark of Adobe Corporation.

Information contained in this document is furnished by TYAN Computer Corporation and has been

reviewed for accuracy and reliability prior to printing. TYAN assumes no liability whatsoever, and

disclaims any express or implied warranty, relating to sale and/or use of TYAN products including

liability or warranties relating to fitness for a particular purpose or merchantability. TYAN retains the

right to make changes to product descriptions and/or specifications at any time, without notice. In

no event will TYAN be held liable for any direct or indirect, incidental or consequential damage,

loss of use, loss of data or other malady resulting from errors or inaccuracies of information

contained in this document.

http://www.TYAN.com

Table of Contents

Before you begin…

Chapter 1: Introduction

1.1 Congratulations

1.2 Hardware Specifications

1.3 Software Specifications

Chapter 2: Board Installation

2.0 Board

2.1 Board Jumpers

2.2 Front Panel Connector

2.3 CMOS Reset

2.4 Mounting the motherboard

2.5 Installing the memory

2.6 Installing the heatsinks

2.7 Attaching drive cables

2.8 Installing Add-in cards

2.9 Connecting external devices

2.10 Installing the power supply

2.11 Finishing up

Chapter 3: BIOS

3.1 Main Setup

3.2 Advanced Settings

3.3 IDE Configuration

3.4 Floppy Configuration

3.5 Boot Settings Configuration

3.6 Super IO Configuration

3.7 Onboard Device Configuration

3.8 USB Configuration

3.9 PCIPnP

3.10 Chipset

3.11 CPU Configuration

3.12 North Bridge Configuration

3.13 ICH3 Chipset Configuration

3.14 Intel PCI-64 Hub Configuration

3.15 ACPI

3.16 ACPI Advanced

3.17 Boot

3.18 Security

3.19 Exit

Chapter 4: Diagnostics

4.1 Beep Codes

4.2 Flash Utility

Appendix: Glossary

Technical Support

……………………………………………..Page 3

……………………………………………..Page 4

……………………………………………..Page 5

……………………………………………..Page 6

……………………………………………..Page 7

……………………………………………..Page 8

……………………………………………..Page 9

……………………………………………Page 10

……………………………………………Page 13

……………………………………………Page 16

……………………………………………Page 18

……………………………………………Page 19

……………………………………………Page 20

……………………………………………Page 21

……………………………………………Page 23

……………………………………………Page 24

……………………………………………Page 25

……………………………………………Page 26

……………………………………………Page 27

……………………………………………Page 28

……………………………………………Page 29

……………………………………………Page 30

……………………………………………Page 35

http://www.TYAN.com

Before you begin…

Check the box contents!

The retail motherboard package should contain the following:

1x Thunder i7500 motherboard

1x 34-Pin floppy drive cable

1x Ultra160/320 LVD SCSI cable (if optional SCSI included)

1x Ultra-DMA-100/66/33 IDE cable

1x Thunder i7500 user’s manual

1x TYAN driver CD

1x Adaptec Ultra160/Ultra320 SCSIdriver diskette (if optional SCSI included)

1x I/O shield with 2 LAN ports

If any of these items are missing, please contact your vendor/dealer for replacement before

continuing with the installation process.

http://www.TYAN.com

Chapter 1: Introduction

1.1 –Congratulations!

You’re now the owner of the most advanced dual Intel processor solution –the Thunder i7500.

Based on Intel’s E7500 chipset, the Thunder i7500 continues to carry the strong Thunder line and

leaves little to be desired. Never leaving anything behind, the Thunder i7500 is HyperThreading

ready –fully supporting HyperThreading enabled Xeons. This means the Thunder i7500 comes

ready to meet networking, storage, and video demands right out of the box. All your networking

needs are handled with ease by both the onboard 10/100Mbps and 1Gbps network ports and

storage support is flexible and speedy with optional dual channel Ultra320 SCSI or Ultra160 SCSI.

With onboard video and support for unprecedented remote management, the Thunder i7500 is

one of the most compelling business solutions available.

The Thunder i7500 supports up to 12GB of Registered ECC PC2100/1600 DDR SDRAM, Xeon

processors 2GHz and beyond, and supports two 133MHz/100M/66Hz PCI-X slots, two

66MHz/33MHz PCI-Xslots and one 32-bit/33MHz slot.

Remember to visit TYAN’s Website at http://www.tyan.com. There you can find information on all

of TYAN’s products with FAQs, distributors list and BIOS setting explanations.

1.2 –Hardware Specifications

Processor

• Dual PGA603 ZIF sockets

• Supports up to two Intel Xeon Processors

• Onboard VRM (VRM 9.1 spec)

• Front-Side Bus support for 400MHz

Chipset

• Intel E7500 chipset

• MCH + ICH3 + P64H2 + FWH

• P64H2 supports two PCI-X busses

• Winbond 83627HF Super I/O ASIC

Memory

• Six 184-pin 2.5v DDR DIMM sockets

• Supports up to 12GB of Registered

PC1600/2100*DDR

memory

• Also supports ECC memory modules

Expansion Slots

• Two 64-bit 100/66/33MHz (3.3-volt) PCI-X

slots

• Two 64-bit 66/33MHz (3.3-volt) PCI-Xslots*

• One 32-bit 33MHz (5-volt) PCI slot

• Total of five usable slots

*The Thunder i7500 supports both PC2100

and PC1600 but Intel’s E7500 chipset will

only operate at PC1600.

Integrated SCSI (manufacturing option)

• Adaptec AIC-7899W (AIC-7902 option)

controller

• Dual-channel Ultra160 (Ultra320 option) SCSI

support

• 160MB/sec maximum data throughput per

channel

• Supports up to 15 LVD SCSI devices per

channel

• Supports Adaptec Zero-Channel RAID (ZCR)

technology in PCI-X slot 2

Integrated 2D/3D Graphics

• ATI RAGE XL graphics controller

• 4MB (8MB optional) frame buffer (SDRAM)

• Standard 15-pin analog VGA port

Server Management Daugtercard (option)

• Q-Logic Zircon Baseboard Management

Controller (BMC)

• I2C and IPMB

• Supports the Intelligent PlatformManagement

Interface (IPMI)

http://www.TYAN.com

Integrated PCI IDE

• Dual-channel master mode

• Supports up to four Enhanced IDE devices

• Support for ATA-100/66/33 IDE and ATAPI

compliant devices

Integrated I/O

• One floppy connector supports up to two

drives

• Two 9-pin 16550-based serial ports

• One 25-pin SPP/ECP/EPP parallel port

• Two USB ports

• PS/2 keyboard and mouse ports

IntegratedLAN

• Gigabit and Fast Ethernet on-board

• Two LAN controllers

-one Intel 82554GC 10/100/1000 controller

-one Intel 82550 10/100 controller

HardwareMonitoring

• Winbond W83782D hardware monitoring

ASIC

• CPU temperature/voltage monitoring

• Chassis intrusion header

• 6(Rev-1) fan headers(3 headers monitoring

ready)

• 6 (Rev-2) fan monitoring headers (all headers

monitoring ready)

• 3 additional fan monitoring from Super I/O

BIOS

• AMI BIOS on 4Mbit/8Mbit Flash ROM

• Auto-configuration of IDE hard drive types

• Multiple boot options

Form Factor

• SSI EEB v3.0 footprint (12" x 13")–see page

10 for website related information.

• EPS12V power connectors(24-pin and 8-pin)

• Stacked parallel (one), serial (one) and VGA

(one) ports

• Stacked USB (two) ports

• LAN (two) ports

• Stacked keyboard and mouse ports

Regulatory

• FCC DoC (Declaration of Conformity)

• European CE (Declaration of Conformity)

1.3 Software Specifications

OS (Operating System) Support

•Microsoft Windows NT 4

•Microsoft Windows 2000

•Microsoft Windows XP

TYAN reserves the right to add support or

discontinue support for any OS with or

withoutnotice.

http://www.TYAN.com

Chapter 2: Board Installation

WARNING: The Thunder i7500 only supports

EPS12V power supplies and will not operate with

other types. Refer to section 2.10 for instructions on

installing EPS12V power supplies. DO NOT use

ATX 2.x, ATX12V and dual AMD power supplies as

they will damage the board and void your warranty.

Only EEB V3.0 form factor chassis is supported.

Other form factors may short the board because the

installation studs are in different locations than

ones required by the Thunder i7500.

Installation

You are now ready to install your motherboard. The mounting hole pattern of the Thunder i7500

matches the SSI system board specifications. Your chassis should support a standard SSI

motherboard form factor.

How to install our products right… the first time

The first thing you should do is read this user’s manual. It contains important information which will

make configuration and setup much easier. Here are some precautions you should take when

installing your motherboard:

(1) Ground yourself properly before removing your motherboard from the antistatic bag.

Unplug the power from your computer power supply and then touch the power supply.

For the safest conditions, TYAN recommends wearing a static safety wrist strap.

(2) Hold the motherboard by its edges and do not touch the bottom of the board.

(3) Avoid touching the motherboard components, IC chips, connectors, and leads.

(4) Avoid touching memory module contacts and IC chips

(5) Place the motherboard on a grounded antistatic surface or on the antistatic bag from

which it came in.

Having reviewed the precautions above, the next step is to take the motherboard out of the

cardboard box and static bag, hold it by its edges and place it on a grounded antistatic surface,

component side up. Inspect the board for damage.

The following pages will detail for you on how to install your motherboard into your chassis, install

processor(s), memory, hard drive and floppy cables/drives and heatsinks.

NOTE DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED

http://www.tyan.com

2.0–Board

The following is an image of the S2720 Thunder i7500.

The above photograph is only a representation of the actual board. Because boards tend to

be updated and go through different revisions, certain components may change and or be

repositioned.The picture above may or may not look exactly like the board you received.

The following page will detail vital components of this board.

http://www.tyan.com

2.1 –Board Jumpers

PCI slots A1, A2, B1 and B2 are all PCI-X slots while PCI slot C is a conventional 32-bit/33MHz

PCI slot. However, PCI slots A1, A2, B1 and B2 will operate at the speed of the slowest PCI card

that is installed into them. If a 33MHz PCI card is inserted into bus A, both A slots will operate at

33MHz. The same rule applies for Bus B slots.

PCI Slot B1: PCI-X 66/33MHz

-Onboard SCSI (optional) and LAN (optional) utilizes this slot’s resources

-3.3 volt cards accepted

PCI Slot B2: PCI-X 66/33MHz

-Onboard SCSI (optional) and LAN (optional) utilizes this slot’s resources

-SupportsAdaptecZero-Channel RAID(Nighthawk)

-3.3 volt cards accepted

PCI Slot A1: PCI-X 100/66/33MHz

-Will operate at 100MHz ifA1 is used butA2 is not with 100MHz PCI card inserted

-Will operate at 66MHz ifA1 andA2 slots are used simultaneously with 66MHz PCI card

inserted

-Will operate at 66MHz if PCI-X 66MHz card is inserted

-Will operate become PCI 64-bit/66MHz if PCI 64-bit/66MHz card is used

-3.3 volt cards accepted

PCI Slot A2: PCI-X 100/66/33MHz

-Will operate at 100MHz ifA2 is used butA1 is not with 100MHz PCI card inserted

-Will operate at 66MHz ifA1 andA2 slots are used simultaneously with 66MHz PCI card

inserted

-Will operate at 66MHz if PCI-X 66MHz card is inserted

-Will operate at PCI 64-bit/66MHz if PCI 64-bit/66MHz card is used

-3.3 volt cards accepted

PCI Slot C1: PCI 32-bit/33MHz

-5 and 3.3 volt cards accepted

Bus A, B and C are independent of each other and do not share the same resources.

http://www.tyan.com

2.2 –Front Panel Connector (J40)

Your chassis will usually come with connectors to install onto the motherboard, such as HDD and

Power LEDs. The Front Panel Connector (J40) has been implemented for such purposes.

2.3 –CMOS Reset (J21)

1..

Clear CMOS

Normal

You can reset the CMOS settings in case an incorrect setting causes system

instability or you have forgotten your system/setup password of have just flashed

your BIOS by using these jumpers.

-Power off system,disconnect power supply from motherboard

-Set jumper J21 to Clear CMOS

-Wait about 5 seconds Set jumper J21 to Normal

http://www.tyan.com

2.4 –MountingtheMotherboard

Before installing your motherboard, make sure your chassis has the necessary motherboard

support studs installed. These studs are usually metal and are gold colored. Usually, the chassis

manufacturer will preinstall the support studs in SSI EEB v3.0 form factor. If you’re not sure which

stud goes where, simply lay the motherboard inside the chassis, aligning the screw holes of the

motherboard to the studs inside the case. If there are any studs missing, you’ll know right away

since the motherboard will not be able to be securely installed.

Some chasses include plastic studs instead of metal ones. These ones are also usable but TYAN

recommends using metal studs with screws to make sure the motherboard does not get jarred

during shipping or lots of movement.

Below is a chart detailing what the most common motherboard studs look like and how they

should be installed.

TIP: Use metal studs if possible, as they hold the motherboard into place more securely than

plastic standoffs.

For more information on the SSI EEB (Entry-Level Electronics Bay) form factor v3.0, please visit

the following website:

http://www.ssiforum.org/docs/entry_level_elebay_spec_v3_o.pdf

Autres manuels pour THUNDER I7500

Table des matières

Autres manuels TYAN Carte mère

TYAN

TYAN S7100 Manuel utilisateur

TYAN

TYAN TOMCAT I II Manuel utilisateur

TYAN

TYAN Triumph i7520 (S6623) Manuel utilisateur

TYAN

TYAN S5512 Manuel utilisateur

TYAN

TYAN TITAN TURBO AT-2 Manuel utilisateur

TYAN

TYAN S7016 Manuel utilisateur

TYAN

TYAN Tigercub 100 S1894 Manuel utilisateur

TYAN

TYAN M4985 Manuel utilisateur

TYAN

TYAN TIGER I7501S Manuel utilisateur

TYAN

TYAN THUNDER K8WE Manuel utilisateur

TYAN

TYAN Triumph i7320 S6621 Manuel utilisateur

TYAN

TYAN S5642 Manuel utilisateur

TYAN

TYAN TOMCAT I875P Manuel utilisateur

TYAN

TYAN Tempest i5000VS S5372-LC Manuel utilisateur

TYAN

TYAN TOMCAT I845 Manuel utilisateur

TYAN

TYAN Tomcat i875P S5102 Manuel utilisateur

TYAN

TYAN Thunder i7500 Pro S2721 Manuel utilisateur

TYAN

TYAN S3115 Manuel utilisateur

TYAN

TYAN S2723 Manuel utilisateur

TYAN

TYAN Thunder 100 S1836 Manuel utilisateur

TYAN

TYAN S8036 Manuel utilisateur

TYAN

TYAN TOMCAT I815T Manuel utilisateur

TYAN

TYAN TRINITY I845 Manuel utilisateur

TYAN

TYAN Thunder K8S Pro Manuel utilisateur

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur