Troy Built Models F86D DOG SABRE Manuel utilisateur
Specifications
Wing Span 60in.
Wing Area 895 sq in.
Flying Weight 15 lb.
Fuselage Length 68 in.
Engine 12lb.-18lb. Thrust Turbine
Recommended Engine Jet Cat P60, KingTech K80
Warning!!! This is not a toy.
The F86D is designed for maximum performance. If you are not
familiar with the operation of turbine powered aircraft please
seek the advice of an experienced modeler. Operating this
model with out prior preparation and experience can cause
injuries.
Before You Begin
1. Read through the instruction manual thoroughly before beginning
construction
2. Check all parts supplied with the kit for defects, and missing parts.
Dry fit all parts that will be glued for proper fit. If any parts are
found to be defective please contact your local dealer or us directly
for assistance.
3. Use proper adhesives for assembly. It is imperative that all glue
joints be very strong for best results and safety.
Adhesives Required:
1. Hysol or 15 min epoxy with micro balloons
2. 30 min epoxy
3. Medium CA
4. Zap-A-Dapa GOO or Automotive Goop
Required Parts for Final Assembly
1. Turbine with 12lb-18lb thrust
2. TX and RX with a minimum of 8 channels
3. 2- Thin wing metal gear servos with a minimum of 65oz torque for
elevators
4. 1- Mini metal gear servo with a minimum of 65 oz of torque for
rudder
5. 4- Standard size metal gear servo with at least 125 oz of torque for
aileronʼs and flaps
6. 1- Mini metal gear servo with a minimum of 65 oz of torque for
steering
7. 1- Mini servo for retract valve
8. Electronic Brake Valve or Mechanical Brake valve
9. UAT
10. Kerosene Fuel tank stoppers and Clunks
11.RX battery with a minimum of 2,200 mah 6v
12.MBA Struts Wheels and Brakes
1.
Locate the plastic hinges with pin and fit into slots that are cut into the wing
panels, trim the slot as necessary. Hinge the ailerons and flaps on each
wing panel using Hysol or 30 min epoxy. (NOTE: If you are using a larger engine,
like the K80, install the flap hinges at the bottom edge of the flap so greater flap throw can be
obtained).
2.
Check the control surfaces on each wing panel and ensure that the glue
has cured and the control surface is secure. Locate the servo openings for
the ailerons and flapʼs and install the servoʼs using wood screws on each
wing. Ensure the servoʼs are facing in the correct direction as per the above
illustration. We recommend Hitec 645MG for the aileron and flaps
3.
Locate 4 composite control horns and cut a slot in each aileron and flap for
the control horn. Use 30 min epoxy or Hysol to secure horn in place and let
cure. Assemble a pushrod using 2 clevisʼs and and secure to the servo.
Pay close attention to have a slop free surface; any excess movement can
cause flutter during high speed flight. For all the pushrods: screw one clevis
on the threaded end, and determine the length of pushrod needed. Cut the
rod and screw the second servo onto the unthreaded end of the rod. Solder
this clevis in place.
4.
Hinge the rudder using 30 min epoxy or hysol and let cure. Check the
control surface after the glue has cured and ensure of a good bond. Locate
the servo opening on the rudder and install the servo using wood screws.
Locate 1 control horn. Cut a slot in the rudder and glue in place using 30
min epoxy or Hysol.
5.
Assemble a pushrod using 2 clevisʼs and and secure to servo. Pay close
attention to have a slop free surface. Any excess movement can cause
flutter during high speed flight.
6.
Locate the servo location in the rudder and glue blocks inside of the rudder
to attach the servo with 90 degree servo mounts ( not supplied ). We
recommend you use a Hitec HS-5245MG. After you complete the above
assembly, drill two holes in the fuselage where the vertical stabilizer
retention pins will fit into. We suggest you use coarse sandpaper and scuff
the surface of the fuselage where you will be glueing this in place. Using
either hysol or 30 min epoxy with micro balloons, glue the vertical stabilizer
to the fuselage.
7.
Locate the two horizontal stabilizer halves and prepare the surfaces to
hinge. Find the plastic hinges with pin and fit into the slots that are cut into
the elevators, trim the slots as necessary. Hinge the elevators on each
panel using Hysol or 30 min epoxy.
8.
The elevator servoʼs are installed just like the ones in the rudder except for
the servo cover, which is held on with clear tape for best utilization of space
in the servo bay. Glue two hard wood blocks and use L brackets (not
supplied) to hold the servo in place. We recommend JR thing wing servoʼs
for the elevator but you can use any thing wing servo that is metal geared
and has at least 65 oz of torque.
9.
We now have to glue the two horizontal stabilizers to the fuselage. Locate
the two carbon fiber spars for the horizontal stabilizer and test fit them into
the fuselage. DO NOT change the hole location, it is critical due to precise
stab incidents. Make sure you scuff the paint on the surface you are going
to glue to get a good bond. Using Hysol or 30 min epoxy with micro
balloons glue the stabilizer to the fuselage.
10.
Turn the fuselage up side down and glue the small tail former in place with
hysol or 30 min epoxy with micro ballons, please see picture below for a
detailed description. At this time check that the main former in the tail is
completely secure. We suggest you use Hysol or 30 min epoxy to fill in any
gaps that we might have missed at the factory. It is very important that this
area of the fuselage is strong and properly glued to avoid any structural
failure in flight. So take your time and check this area carefully.
11.
Before installing the turbine run all wires from the tail along the top of the
fuselage. Use either aluminum tape or heat shield to guard the wires from
the heat. Slide the dual walled exhaust pipe into the fuselage. Trim the
rear of the fuselage (primarily on the bottom) to allow the thrust pipe to exit
the fuselage with only a small gap all around. Locate the thrust pipe former
and glue in place. The exact location of the installation of this former varies
depending of the turbine used. We suggest you use the instructions from
your specific turbine manufacturer for proper installation of your turbine.
We usually use about 1/2 inch gap from the end of the turbine exhaust to
the beginning of the bell mouth on the thrust pipe.
After you have test fit the turbine and the thrust pipe glue the ply former in
place with Hysol or 30 min epoxy with micro balloons and use two sheet
metal screws to affix the thrust pipe to the former.
12. The wings are held in place by two bolts, one in each wing. You will
have to drill the hole in the fuselage to accommodate the bolt. The bolt
hole will be approximately 1 inch in front of the fuel tanks. You will have to
install two carbon fiber anti-rotation pins on each wing (supplied). One in
the leading edge and one in the trailing edge wing root. When drilling the
holes in the fuselage ensure the wings are at the correct incidence. With
the fuselage level the stabilizer will be 0 degrees incidence and the wings
will be approximately 1-1 1/2 degrees positive incidence
13. The two fuel tanks that come with the kit have to be assembled. After
you complete the assembly of the clunk, tubing etc. Secure the tanks to the
fuselage sides with a drop of goop. Do not use to much glue only a small
amount is necessary in case you need to remove them later.
14. We recommend you install the UAT on the right side of the airplane
looking back. If you look at the picture below you can see the UAT is on
the right side in front of the steering servo. Use goop to glue it to the
fuselage side.
Table des matières
Autres manuels Troy Built Models Jouet
Troy Built Models
Troy Built Models Do-335 Manuel utilisateur
Troy Built Models
Troy Built Models B-25 Mitchell Manuel utilisateur
Troy Built Models
Troy Built Models Electric Beaver Manuel utilisateur
Troy Built Models
Troy Built Models P-51B Mustang Manuel utilisateur
Troy Built Models
Troy Built Models FAIREY SWORDFLSH Manuel utilisateur
Troy Built Models
Troy Built Models BF-110C ZERSTORER Manuel utilisateur
Troy Built Models
Troy Built Models Hawker hurricane MK.IIa Manuel utilisateur
Troy Built Models
Troy Built Models P-40 warhawk Manuel utilisateur
Troy Built Models
Troy Built Models PA-25 Manuel utilisateur
Troy Built Models
Troy Built Models 50cc SPITFIRE Manuel utilisateur
Troy Built Models
Troy Built Models P-39 Airacobra Manuel utilisateur
Troy Built Models
Troy Built Models SPITFIRE MK.XIV Manuel utilisateur
Troy Built Models
Troy Built Models Aichi D3A1 Manuel utilisateur
Troy Built Models
Troy Built Models F-4u Corsair Manuel utilisateur
Troy Built Models
Troy Built Models P-47D Thunderbolt Manuel utilisateur
Troy Built Models
Troy Built Models T-28 Trojah Manuel utilisateur
Troy Built Models
Troy Built Models Ki84 Hayate Manuel utilisateur
Troy Built Models
Troy Built Models Bonanza V-35 Manuel utilisateur
Troy Built Models
Troy Built Models Hawker Typhoon Manuel utilisateur
Troy Built Models
Troy Built Models ME - 109 Manuel utilisateur
