Troy Built Models 50cc SPITFIRE Manuel utilisateur

Top view

Side View

40mm

RUDDER

Adjustment.

153mm

Air tank

Switch

Air inlet

3-way

pressure inlet

3-way

pressure inlet

3-way

pressure inlet

The status when the

gear up

Pull out length of 8mm

to make gear down

Air valve Air valve

Make sure to assemble retracts as instructed below.

Two wheel retract system

Quick release connector

Pressure reduction inlet

Strut

3-way pressure inlet 3

Pressure reduction inlet 1

Air tank

Air inlet

Air line (3000mm)

Quick release connector

Strut

( 90 )

Switch

Clevis

Rod (2X300mm)

Retainer

TP Screw(2x14mm) 2

Ø1.7mm

Ø0.2mm

Pleas notice the inner diameter

of eachside the pressure reduction inlet.

Please insure the sealing of theretract

system before flight .

The centre of the Gravity.

50cc SPITFIRE

SAFETY PRECAUTIONS

INSTRUCTION MANUAL

First-time builders should seek advice from people having building

experience.If misused or abused,it can cause serious bodily injury

and damage to property.

Fly only in open areas and preferably at a dedicated R/C flying site.

We suggest having a qualified instructor carefully inspect your

airplane before its first flight.Please carefully read and follow all

instructions included with this airplane,your radio control system

and any other components purchased separately.

(The people under 18 years old is forbidden from flying this model)

This R/C airplane is not a toy!

Specifications:

Length: 1935mm(76.2＂)

Wing span: 2260mm(89＂)

Wing area: 93sq.dm(10sq.ft)

Wing loading: 108.6g/sq.dm(35.6oz/sq.ft)

Flying weight: 10.1kg(22.2lbs)

Radio: 6ch & 8servos

Engine: 50cc gas engine

210mm

195mm

TP Screw (3x20mm)

Wooden Block

TP Screw (2.6x14mm)

Collar (5mm)

Wooden supporter

Collar (5mm)

Washer (3x6mm)

Wooden Block(43x28x26mm)

Gear door

Collar (5mm)

Wheel (115mm)

Landing gear(5mm) 2

TP Screw (3x20mm )

Landing gear straps

TP Screw (2.6x14mm)

Washer (3x6mm)

Wooden Block(25x15x13mm)

Assemble the wheel and gear door to landing gear.

30mm

40mm

AILERON

FLAP

Side View

Top view

Position for

right diagram.

ELEVATOR

Side View

30mm

Centre of Gravity.

Adjustment.

Epoxy the landing gear to the wing steadily.

Adjustment.

AILERON FLAP FLAP

Wheel (115mm)

Epoxy the fiber deconations to aprropriate position

on the bottom of the wing.

Accessory list for the coming installation steps.

50cc gas engine

22″X8-10

6 channel radio for aiplane is highly recommended for this model.

Optional parts: rubber wheel with metal hub.

We strongly recommen you use the thread lock for all the screws when you build your model.

4.75 in Spinner

Gasoline tube

Gasoline

250mm

The deconation can be removed

when unasemble the wings.

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

1.5mm

TP Screw (2.3x8mm)

Epoxy plies inside the fuselage under the cowing and

mount the cowing with TP screw as illustration.

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Deconation

48mm

Ply (2mm)

Epoxy plies to relevant position inside the fuselage as

below for assembling the cowling.

Epoxy plies inside the fuselage under the cowing and

mount the cowing with TP screw as illustration.

Epoxy the PVC decoration parts to the appropriate

position on the wing as illustration.

Disassemble the wing and set the ply to the slot

in the wing root.

Assemble the wings together,stick masking tape around

the ply and add some epoxy glue to top of the ply.

Assemble the air intake deconation to appropriate

position on the ply and wait until the glue dry.

Stick masking tape around

the ply to keep clear.

Clevis

Rod (2.5x300mm)

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Screw (4x40mm)

Washer

Lock Nut (4mm )

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Make sure hinges are

mounted in the same line.

Pin hinge(4.5x67mm)

1mm

Trailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Aileron

Rod (2.5x300mm)

Washer

Washer(4x14mm)

Lock Nut (4mm )

Clevis

Nut (3mm )

Collar (3mm)

Screw (3x10mm)

Screw (4x40mm)

Washer(4x14mm)

Collar (3mm)

Screw (4x40mm)

Washer

Lock Nut (4mm )

Washer(4x14mm)

Clevis

Screw (3x10mm)

Nut (3mm )

Collar (3mm)

Rod (2.5x300mm)

Install the servo as the illustration below

Install the nylon control horn and connect the linkage.

Apply instant AB glue to aileron and pin hinge.

Assemble the aileron to main wing with instant type AB glue. Be careful

to ensure the moving parts of the hinges are able to move freely.

Keep some space about 1mm width between the

trailing edge and the aileron.

Accessory list for the coming installation steps.

Install the servo as the illustration below

TP Screw (2.3x12mm)

4mm

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Flap

1mm

Make sure they are in

the right position while

installing.

Trailing

edge

1.5mm

Pin hinge(24x24mm)

173o

2mm

Keep some space

between the flaps.

Metal wire (1.7x210mm)

Pin hinge(24x24mm)

Metal wire (1.7x210mm)

Rod (2.5x300mm)

Clevis

Lock Nut (4mm )

Screw (3x10mm)

Nut (3mm )

Screw (4x40mm)

Washer

Clevis

Rod (2.5x300mm)

TP Screw (2.3x12mm)

Wooden Block(20x20x8mm)

Servo tray(68.5x56.5x2mm)

Screw (4x35mm)

Washer

Lock Nut (4mm )

Washer(4x14mm)

Collar (3mm)

Washer(4x14mm)

Secure the servo.Install the nylon control horn

and connect the linkage.

Epoxy the flaps to the wings as illustration.

Keep some space about 1mm width between

trailing edge and flap.

Connect the two flaps with metal wire,keep some space

between them and epoxy the pinned hinges to the flaps

as below.

Accessory list for the coming installation steps.

Add a rubber ring to the

clevis for insuring safety

Fiber deconations

Deconation

Cut off the surplus part from the cowling,exhausts and

canopy carefully.

Pvc part

AA'

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming off during flights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

The sketch map should be when the stabilizer

assembly completion.

Clevis 1

Rod (2x300mm) 1

Retainer

Ring

Air tank

Switch

Install the servo of swith.

The servos installation finished sketch map.

Ply(15x15x2mm)

TP Screw (2.3x8mm)

Canopy

Pvc part

Throttle servo

Rudder servo

Elevator servo

switch servo

Epoxy the exhaust the the cowling as figure.

Ply (2mm)

56 58

Accessory list for the coming installation steps.

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Clevis 1

Rod (2x300mm) 1

Retainer

Ring

Air tank

Switch

Washer(3x15mm)

Screw (3x80mm)

Lock Nut (3mm )

Clevis

Aluminum tube

Steel wire

Steel wire (0.5x3000mm)

Clevis

Washer(3x15mm)

Lock Nut (3mm )

Screw (3x80mm)

Copper joiner

The sketch map after the rudder shaft assemble finished.

Steel wire (0.5x3000mm)

3mm

30mm

Drill a hole to appropriate position in the

rudder as illustration.

Collar

Tail landing gear

TP Screw (2.3x8mm)

1.5mm

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Install the servo.

The servos installation finished sketch map.

Rudder servo

35mm

95mm

Plastical tube(3x30mm)

Drill a small hole to appropriate possition in the

fuselage for installing the plastical tube.

3mm

Steel wire

Copper joiner

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Aluminum tube

Rudder servo

Epoxy plies to appropriate position in the fuselage and

assemble the tail gear cover with screw.Then assemble

the wheel as illustration.

Connect the servo of rudder and the shaft for rudder

with steel wire as illustration.

49 52

Accessory list for the coming installation steps.

Install the nylon control horn and connect the linkage.

4mm

TP Screw (2.3x12mm)

1.5mm

Secure the servo.Install the nylon control horn

and connect the linkage.

Main wing joiner(25x630mm)

Main wing joiner(20x570mm)

Rod (2.5x300mm)

Clevis

Lock Nut (4mm )

Screw (3x10mm)

Nut (3mm )

Screw (4x35mm)

Washer

Washer(4x14mm)

Blind Nut (4mm)

Screw (4x40mm)

Gear door

Wheel (115mm)

TP Screw (3x20mm)

Washer (3x6mm)

PVC part

Retracts strut

LockNut(4mm)

Wooden Block

Note:rubber wheels oleo struts

and retracts are optional.

5mm

Rib template (3mm ply)

Washer (4x12mm) 4

Wood dowel (6x50mm)

LockNut(4mm)

Screw (4x75mm) 2

Wheel (115mm)

Wooden Block

Bushing (8X4mm)

C = C"

side wing centre wing

Rod (2.5x300mm)

Washer

Lock Nut (4mm )

Clevis

Nut (3mm )

Collar (3mm)

Screw (3x10mm)

Screw (4x40mm)

Washer

Lock Nut (4mm )

Clevis

Screw (3x10mm)

Nut (3mm )

Collar (3mm)

Rod (2.5x300mm)

Washer(4x14mm) 2

Washer(4x14mm)

Reinforcement Plate (25x2mm)

Mount the gear door and the wheel to the retract.

Be care to notice the difference between

the left and the right wheel well.

Cut away the surplus parts of plastic cover

carefully along the shaded line.

The sketch maps when the retract up and down.

Trim the relevant position flat when assemble

the linkage of the servo tray.

Accessory list for the coming installation steps.

TP Screw (3x20mm)

20mm

100mm

200mm

R10mm

Air tube

Servo wire

Main wing joiner(25x620mm)

Main wing joiner(20x570mm)

Main wing joiner(25x620mm)

Main wing joiner(20x570mm)

TP Screw (3x20mm) 8

Rib template (2mm ply)

6mm

Wood dowel (6x50mm)

Rib template (2mm ply)

Wood dowel (6x50mm)

6mm

Assemble the retracts to the appropriate position

in the gear house.

According to the rib template drill a hole to one wing

root and epoxy wood dowel in it.

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Trim holes in the appropriate position in the wing

and drag the servo wire and the air tube out.

According to the rib template drill a hole in

the other wing root.

Connect the two wings with main wing joiners.

Trim the sheet carefully from the wing for assembling

the wheel well,epoxy the wheel well to it.

16 19

Steel wire (0.5x3000mm)

2.5mm

Pin hinge(2.5x48mm)

Make sure hinges are

mounted in the same line.

35mm 110mm 130mm

2.5mm

1mm

Wooden Block (9mm Ply)

Wooden Block (3mm Ply)

TP Screw(3x20mm)

Washer (3x6mm)

TP Screw(3x20mm)

Washer (3x6mm)

Wooden Block (9mm Ply)

Wooden Block (3mm Ply)

Wooden Block (9mm Ply)

Wooden Block (3mm Ply)

Tail gear cover

Be carefule don't let the arm touch

the fuselage when it works

Drill holes to appropriate position in the rudder and epoxy

the ping hinges in them

1mm

Rudder

Tailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Keep some space about 1mm width between

the tailing edge and the rudder.

Drill holes to the relevant position in the tailing edge

and epoxy the rudder to them.

Assemble the wheel mount to the thick wooden block

with screw,cut the surplus parts and epoxy the thinner

wooden block to it as illustration.

Connect the servo of rudder and the arm of tail

landing gear with steel wire.

Epoxy the the whole wheel mount set to the form in the

fuselage and be carefule don't let the arm touch the

fuselage when it works

Accessory list for the coming installation steps.

TP Screw (2.3x8mm)

Ply (15x15x3mm) 8

Fuel supply line

Fuel spray line

Air pressure line

Plastical tube(3x30mm)

Tail gear mount

Collar (3mm) 2

Tail landing gear(3mm)

Tail wheel (45mm)

TP Screw(3x20mm)

Washer (3x6mm)

Steel wire (0.5x1200mm)

Clevis

Washer(3x15mm)

Lock Nut (3mm )

Screw (3x80mm)

Copper joiner

Collar

Tail landing gear

Tail gear mount

Collar

Pin hinge(2.5x48mm)

Wooden Block (9mm Ply)

Wooden Block (3mm Ply)

Linkage Stopper

Washer (2mm)

Nut (2mm)

Set screw (3x4mm)

Washer (

2mm

)

Set screw (3x4mm)

Assemble the servos.

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Mount the fuel tank to the fuselage.

Assemble the throttle servo to appropriate

position in the fuselage.

Assembly of the fuel tank. The sketch map when assemble the tail landing

gear to the wheel steeling mount.

Accessory list for the coming installation steps.

AA'

Make sure to glue securely.

If not properly glued, a failure in flight may occur.

Temporarily fasten down the main wing and

check its correct position.

Securely glue together.If coming off during flights,

you'll lose control of your airplane which leads

to accidents!

A=A'

B=B'

Blind Nut (4mm)

Steel wire (0.5x3000mm)

U-style wire (130x25x3mm)

TP Screw (2.3x12mm)

Pin hinge(2.5x48mm)

Wood dowel (4x30mm)

Rib template (2mm ply)

Stab joiner (12x300mm)

30mm

50mm

120mm

5.2mm

Blind Nut

Screw(4x75mm)

Screw(4x40mm)

4mm

Wood dowel (4x30mm)

According to the rib templete drill holes to appropriate

position in the tail fuselage.

According to the rib templete drill holes one the

stabilizer root and epoxy wood dowel in them.

4mm

Rib template (2mm ply)

Washer(4x12mm)

Wood dowel (4x30mm)

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Reinforcement Plate(25x2mm)

Screw(4x40mm)

Screw(4x75mm)

Washer(4x12mm)

Reinforcement Plate 4

The sketch map should be when the stabilizer

assembly completion.

Drill holes in the appropriate position through the wing

to fuselage,set blind nut in the fuselage.

Fix the wings to the fuselage with screws.

Accessory list for the coming installation steps.

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

Steel wire (0.5x3000mm)

U-style wire (3mm)

2x20mm

Stab joiner (12x300mm)

3mm

Make sure hinges are

mounted in the same line.

Pin hinge(4.5x67mm)

30mm 60mm 76mm

1mm

Tailing

edge

Cut away the rubber tube when

the epoxy glue dried.

Make sure they are in

the right position while

installing.

Elevator

Steel wire (0.5x3000mm)

Apply instant type AB glue to elevator and pin hinge.

Keep some space about 1mm width between

elevator and tailing edge.

Set the U-style wire through the enlarged hole as below.

Epoxy the stabilizer to the fuselage,trim a small slot in

appropriate position in the stabilizer and glue the U-style

wire to it.

Clevis

Copper joiner

Screw (2x10mm)

Nut (2mm )

Washer(2x5mm)

Steel wire

Copper joiner

Lock Nut (2mm )

Screw (2x10mm)

Ball joint

Washer(2x5mm)

Aluminum tube

Install the servo.

Securely glue together. If coming off during flights, you 'll

lose control of your airplane which leads to accidents!

3mm

Epoxy the elevator to the stabilizer.

In case of 2-cycle & 4-cycle engine.

6.2mm

Blind Nut

193mm

Blind Nut (5mm) 4

Washer

Screw

Washer

Linkage Stopper

Washer

Spring Washer

Screw

Plastic tube (2x650mm)

Washer 4

Blind Nut (5mm)

Fuel tank (550cc) 1

Engine mount is a movable cylinder.

Elevator servo

Fix the elevator servo to appropriate position

in the fuselage.

The side view when the engine installation finished,the steps should be assemble

the engine to engine mount after step 36 &37,adjust the engine mount to a proper

position,epoxy the engine mount to the fuselage with AB glue.

Assemble the engine.

The engine will be 2 degree right skewed once the

engine install completion.

Drill 4 holes in appropriate position in the movable

cylinder and set blind nut in them.

Accessory list for the coming installation steps.

Table des matières

Autres manuels Troy Built Models Jouet

Troy Built Models

Troy Built Models P-47D Thunderbolt Manuel utilisateur

Troy Built Models

Troy Built Models Hawker Typhoon Manuel utilisateur

Troy Built Models

Troy Built Models ME - 109 Manuel utilisateur

Troy Built Models

Troy Built Models P-40 warhawk Manuel utilisateur

Troy Built Models

Troy Built Models P-39 Airacobra Manuel utilisateur

Troy Built Models

Troy Built Models B-25 Mitchell Manuel utilisateur

Troy Built Models

Troy Built Models FAIREY SWORDFLSH Manuel utilisateur

Troy Built Models

Troy Built Models Fw-190 D9 Manuel utilisateur

Troy Built Models

Troy Built Models Bonanza V-35 Manuel utilisateur

Troy Built Models

Troy Built Models Do-335 Manuel utilisateur

Troy Built Models

Troy Built Models 105” Curtiss JN-4 Manuel utilisateur

Troy Built Models

Troy Built Models Memphis Belle B-17 Manuel utilisateur

Troy Built Models

Troy Built Models T-28 Trojah Manuel utilisateur

Troy Built Models

Troy Built Models SHOCKJET MF 6 Manuel utilisateur

Troy Built Models

Troy Built Models ROBIN DR400 Manuel utilisateur

Troy Built Models

Troy Built Models BF-110C ZERSTORER Manuel utilisateur

Troy Built Models

Troy Built Models F86D DOG SABRE Manuel utilisateur

Troy Built Models

Troy Built Models Aichi D3A1 Manuel utilisateur

Troy Built Models

Troy Built Models F-4u Corsair Manuel utilisateur

Troy Built Models

Troy Built Models SPITFIRE MK.XIV Manuel utilisateur

Troy Built Models

Troy Built Models Stinson 108 Manuel utilisateur

Troy Built Models

Troy Built Models P-51B Mustang Manuel utilisateur

Troy Built Models

Troy Built Models Hawker hurricane MK.IIa Manuel utilisateur

Troy Built Models

Troy Built Models PA-25 Manuel utilisateur

Manuels Jouet populaires d'autres marques

marklin

marklin 37321 Manuel utilisateur

Canon

Canon PAPER CRAFT Manuel utilisateur

GREAT PLANES

GREAT PLANES Pitts M-12S Manuel utilisateur

NOCH

NOCH 14261 Manuel utilisateur

Hausler

Hausler 450 SE V2 Manuel utilisateur

Dynaflite

Dynaflite Daydream Manuel utilisateur

MiniacRC

MiniacRC MIGHTY MINI P40 WARHAWK Manuel

Kenner

Kenner Batman 63651 Manuel utilisateur

LEGO

LEGO 8527 Manuel utilisateur

iKarus

iKarus ECO 8 Manuel utilisateur

Multiplex

Multiplex EasyStar II Mode d’emploi

Walkera

Walkera 38 Mode d’emploi

Hasbro

Hasbro TRANSFORMERS BUMBLEBEE Manuel utilisateur

MD MXION SWD Manuel utilisateur

Mattel

Mattel Disney Pixar Cars Cozy Cone Spiral Rampway Manuel utilisateur

marklin

marklin 39671 Manuel utilisateur

Meccano

Meccano 15103 Manuel utilisateur

LEGO

LEGO TECHNIC 8735 Manuel utilisateur