Tripp Lite BCPRO1400 Manuel utilisateur

Owner’s Manual

1111 W. 35th Street Chicago, IL 60609 USA

Customer Support: (773) 869-1234 • www.tripplite.com

Important Safety Instructions 2

Quick Installation 3

Basic Operation 4

Storage & Service 7

Specifications 7

BC Pro®

120V Input/Output Standby UPS Systems

Español 9

Français 17

UL1778

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:31 PM Page 1

UPS Location Warnings

• Install your UPS indoors, away from excess moisture or heat, conductive contaminants,

dust or direct sunlight.

• For best performance, keep the indoor temperature between between 32º F and 104º F

(0º C and 40º C).

• Leave adequate space around all sides of the UPS for proper ventilation.

UPS Connection Warnings

• Connect your UPS directly to a properly grounded AC power outlet. Do not plug the

UPS into itself; this will damage the UPS.

• Do not modify the UPS's plug, and do not use an adapter that would eliminate the UPS's

ground connection.

• Do not use extension cords to connect the UPS to an AC outlet. Your warranty will be

voided if anything other than Tripp Lite surge suppressors are used to connect your UPS to

an outlet.

• If the UPS receives power from a motor-powered AC generator, the generator must

provide clean, filtered, computer-grade output.

Equipment Connection Warnings

• Do not use Tripp Lite UPS Systems for life support appliances in which a malfunction

or failure of a Tripp Lite UPS System could cause failure or significantly alter the

performance of a life-support device.

• Do not connect surge suppressors or extension cords to the output of your UPS. This

might damage the UPS and will void the surge suppressor and UPS warranties.

Battery Warnings

• Your UPS does not require routine maintenance. Do not open your UPS for any reason

except battery replacement. There are no user-serviceable parts inside.

• Battery replacement must be performed by qualified service personnel. Because the

batteries present a risk of electrical shock and burn from high short-circuit current,

observe proper precautions. Unplug and turn off the UPS before performing battery

replacement. Use tools with insulated handles, and replace the existing batteries with the

same number and type of new batteries (Sealed Lead-Acid). Do not open the batteries.

Do not short or bridge the battery terminals with any object.

• The UPS batteries are recyclable. Refer to local codes for disposal requirements, or in

the USA only call 1-800-SAV-LEAD for recycling information. Do not dispose of the

batteries in a fire.

• Do not attempt to add external batteries to the UPS.

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains instructions and warnings that should be followed during the

installation, operation and storage of all Tripp Lite UPS Systems. Failure to heed these

warnings will void your warranty.

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:31 PM Page 2

Quick Installation

Connect your UPS to

an electrical outlet.

Your UPS will run a self-test after it is

plugged in. See Basic Operation to understand

the results of its self-test.

Plug your computer, monitor

and external modem into

UPS/Surge outlets. Plug

other equipment into

Surge-only outlet(s).

Separate UPS/Surge and Surge-only outlet(s)

are identified on the back of your UPS. Your

UPS is designed to support only computer

equipment.You will overload your UPS if you

connect high power draw equipment such as

household appliances, laser printers or surge

suppressors to its UPS/Surge outlets.

Select UPS Operating

Mode.*

Press the ON/OFF button to toggle your UPS

between the UPS (“ ” LED lit) and the

CHARGE ONLY (“ ” LED flashing)

modes. Choose the operating mode based on

your location:

USA, Canada & Western Europe:

• Leave the UPS in the UPS mode at all times.

All Other Countries:

• Put the UPS in the CHARGE ONLY

mode when you are not using connected

equipment.

(WARNING! When set to “CHARGE ONLY,” the UPS

will not provide battery backup during a blackout or

brownout)

• Put the UPS in the UPS mode when you

areusing connected equipment.

*See Basic Operation section for a complete explanation

of each mode.

NORM DELAY

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 3

These connections are optional. Your UPS will function properly without these connections.

Modem/Fax Surge Suppression

Using telephone cords, connect your wall jack to

the UPS jack marked “LINE” (or “IN”) and your

equipment to the UPS jack marked “EQUIP” (or

“OUT”). This will protect your equipment from

surges over a telephone line, but you should make

sure that your equipment is also protected against

surges on the AC line.

USB Communications

Use any USB cable to connect the USB port of

your computer to the USB port of your UPS.

Download the PowerAlert UPS monitoring

software program appropriate for your operating

system from www.tripplite.com and install it on

your computer.

Quick Installation

optional

NORM DELAY

Basic Operation

Buttons

Use the ON/OFF button to do three things:

Switch your UPS’s Operating Mode: While your UPS is plugged

into a live AC outlet, press the ON/OFF button and hold it until you

hear a beep (about 2 seconds) to toggle between the following

operating modes. Choose your UPS’s operating mode based on the

regional guidelines in Step 3 of the Quick Installation section.

• UPS Mode: ENABLES battery backup. UPS Conditions: The UPS

charges its battery and supplies power at its receptacles when it is

receiving utility line power. If utility power fails, the UPS provides

power from its batteries. The “ ” indicator light is lit. Setting

Advantages: Provides battery backup during blackouts or brownouts.

• CHARGE ONLY Mode: DISABLES battery backup. UPS

Conditions: The UPS charges its battery and supplies power at its

receptacles when it is receiving utility line power. The “ ” indicator

light is flashing. Setting Advantages: Continues to charge the battery

when power is present while turning OFF the inverter to prevent

battery depletion during power outages when equipment is not in use.

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 4

Cold-Start Your UPS: You may “cold start” your UPS and use it as a

stand-alone power source when utility power is not present, providing

that the UPS battery is charged. To “cold start” your UPS, press and

hold the ON/OFF button until you hear a beep (about 2 seconds), then

release it. The “ ” indicator light will illuminate and AC power

inverted from stored battery power will be provided at its receptacles.

Shut Down Your UPS: Press and hold the ON/OFF button when AC

line power is absent (i.e. during a blackout, or when the UPS is

unplugged) to deactivate your UPS.

Use the MUTE/TEST button to do two things:

Silence the UPS On-Battery Alarm: Press and hold this button to

silence the UPS On-Battery alarm, a series of short beeps followed by

a brief pause that is activated when the UPS is providing AC power

from battery. Note: When the battery is nearly depleted, the Low

Battery alarm—a continuous beep that cannot be silenced—will alert

you to immediately shut down connected equipment.

Run a Self-Test: Your UPS performs a self-test whenever it is first

plugged in. To have it run a self-test at another time, leave your

connected equipment on. With your UPS plugged in and in the UPS

mode, press and hold this button until you hear a beep (about 2 seconds)

then release it.

Results of a Self-Test: All the LEDs will be lit and the UPS will emit

several short beeps as it momentarily switches to battery to test its

charge and load capacity. The test will last at most 10 seconds. If the

inverter is overloaded, the UPS will continue to beep after the test; if

this happens, remove some of the load and run the self-test again. If the

batteries seem weak, the “ ” LED will stay lit and the UPS will

continue to beep after the test; if this happens, let UPS charge its

batteries for 12 hours and repeat the test. If the condition persists,

contact Tripp Lite for service. CAUTION: Do not unplug your UPS to

test its batteries. This will remove safe electrical grounding and may

introduce a damaging surge into your network connections.

All Indicator Light descriptions apply when the UPS is plugged into an AC outlet and turned on.

LINE POWER: This green light will turn ON whenever your UPS is

receiving normal AC line power. It will flash while the UPS is in

CHARGE ONLY mode to indicate that the UPS will not provide

battery backup during a blackout or brownout.

BATTERY POWER: This yellow light will turn ON when your UPS

is providing your equipment with battery power.

Basic Operation

continued

Indicator Lights

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 5

BATTERY CHARGE: This red light will turn ON continuously

after the UPS runs a self-test to indicate that the UPS’s battery is

weakly charged. If it remains lit after you have allowed the UPS to

charge for twelve hours and run a second self-test, contact Tripp Lite

for service.

Basic Operation

continued

Other UPS Features

AC Receptacles

“UPS/Surge” receptacles are used to provide your connected

equipment with AC line power during normal operation and battery

power during blackouts and brownouts. They also protect your

equipment against damaging surges and line noise. “Surge-only”

receptacles (identified on the back of the UPS) are used to provide

peripherals with surge protection without committing precious

battery power to support them during blackouts.

RJ45 Phone Jacks

These jacks protect your equipment against surges over a telephone

line. Connecting your equipment to these jacks is optional. Your UPS

will still work properly without this connection.

USB Port

The USB port connects your UPS to any USB workstation or server.

Using this port, your UPS can communicate line-fail and low-battery

status to your computer. Use with Tripp Lite software and any USB

cable to automatically save open files and shut down equipment during

a blackout. Contact Tripp Lite Customer Support or consult your

power protection software manual for more information.

Battery Replacement Door

Under normal conditions, the original battery in your UPS will last

several years. Battery replacement should be performed only by

qualified service personnel. Refer to “Battery Warnings” in the Safety

section on page 2.

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 6

Specifications

Tripp Lite has a policy of continuous improvement. Specifications are subject to change without notice.

Model: BCPRO600

Series: AGOM1000USBKSR6

Input Voltage/Frequency: 120V/60 Hz

Output Capacity (VA/Watts): 600/345

Battery Runtime

(Half Load/Full Load) Minutes: 19/7

Battery Recharge Time: 2-4 hrs.

Approvals: UL, cUL, NOM

ALL UNITS:

Output Waveform Line Mode (filtered sinewave); Output Waveform Battery Mode (PWM sine wave); AC Surge Suppression (exceeds

IEEE 587 Cat. A & B standards); AC Noise Attenuation (>40 dB at 1MHz); AC Protection Modes (H to N, H to G, N to G).

FCC RADIO/TV INTERFERENCE NOTICE:

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the

instruction manual, may cause interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the device off and on, the user is encouraged to try to correct the interference using one or more of the

following measures: reorient or relocate the receiving antenna; increase the separation between the equipment and receiver; connect

the equipment into an outlet on a circuit different from that which the receiver is connected; consult the dealer or an experienced

radio/television technician for help. The user must use shielded cables and connectors with this product. Any changes or

modifications to this product not expressly approved by the party responsible for compliance could void the user's authority to

operate the equipment.

Storage

All connected equipment should be turned off, then disconnected from the UPS to avoid battery

drain. Unplug your UPS from its AC receptacle, then press and hold its ON/OFF button to

deactivate it. Your UPS is now ready for storage. If you plan on storing your UPS for an

extended period of time, fully recharge the UPS batteries once every three months by plugging

the UPS into a live AC outlet and letting the UPS charge for 4 to 6 hours. If you leave your UPS

batteries discharged for an extended period of time, they will suffer a permanent loss of

capacity.

Service

If returning your UPS for service, contact your local Tripp Lite dealer or distributor. They will

refer you to a service center. Please carefully pack the UPS using the ORIGINAL PACKING

MATERIAL that came with the unit. Enclose a letter describing the symptoms of the problem.

If the UPS is within the warranty period, enclose a copy of your sales receipt.

Storage & Service

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 7

Specifications

continued

CONSUMER INFORMATION AND FCC REQUIREMENTS (U.S.A. ONLY)

1. This equipment complies with Part 68 of the FCC rules. On the top or bottom of this equipment is a label that contains, among

other information, the FCC registration number for this equipment. If requested, provide this information to your telephone

company.

2. If your Fax/Modem Protector causes harm to the telephone network, the telephone company may temporarily discontinue

your service. If possible, they will notify you in advance. But if advance notice isn't practical, you will be notified as soon as

possible. You will be advised of your right to file a complaint with the FCC.

3. Your telephone company may make changes in its facilities, equipment, operations or procedures that could affect the

operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain

uninterrupted service.

4. If you experience trouble with this Fax/Modem Protector, please contact Tripp Lite Customer Support, 1111 W. 35th Street,

Chicago, Illinois 60609; Phone (773) 869-1234 for repair/warranty information. The telephone company may ask you to

disconnect this equipment from the network until the problem has been corrected or you are sure that the equipment

is not malfunctioning.

5. This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to

state tariffs. (Contact your state public utility commission or corporation for information.)

EQUIPMENT ATTACHMENT LIMITATIONS (MODELS WITH THE INDUSTRY CANADA LABEL IN CANADA ONLY)

Notice: The Industry Canada label identifies certified equipment. This certification means that the equipment meets the

telecommunications network protective, operational and safety requirements as prescribed in the appropriate Terminal Equipment

Technical Requirements Document(s). The Department does not guarantee the equipment will operate to the user’s satisfaction.

Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local

telecommunications company. The equipment must also be installed using an acceptable method of connection. The customer

should be aware that the compliance with the above conditions might not prevent degradation of service in some situations.

Repairs to certified equipment should be coordinated by a representative designated by the supplier. Any repairs or

alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company

cause to request the user to disconnect the equipment.

Users should ensure for their own protection that the electrical ground connections of the power utility, telephone lines and

internal metallic water pipe system, if present, are connected together. This precaution may be particularly important in rural

areas. Caution: Users should not attempt to make connections themselves, but should contact the appropriate electric inspection

authority, or electrician, as appropriate.

93-2031 (200202076)

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 8

Manual del usuario

1111 W. 35th Street Chicago, IL 60609 EE.UU.

Atención al cliente: +1 (773) 869-1234 • www.tripplite.com

Importantes instrucciones de seguridad 10

Instalación rápida 11

Operación básica 12

Almacenamiento y servicio 15

Ficha técnica 15

BC Pro®

Sistemas de energía ininterrumpible de 120V de entrada/salida

English 1

Français 17

UL1778

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 9

Advertencias sobre la colocación del UPS

• Instale el sistema UPS bajo techo, alejado del calor o la humedad excesivos, de los

contaminantes conductivos, del polvo o de la luz solar directa.

• Para lograr el mejor rendimiento, mantenga la temperatura interior entre 0º C y 40º C

(32º F y 104º F).

• Mantenga suficiente espacio alrededor del sistema UPS para permitir una ventilación adecuada.

Advertencias sobre la conexión del UPS

• Conecte su sistema UPS directamente a una toma de energía de CA con conexión

adecuada a tierra. No conecte el sistema UPS a sí mismo, ya que esto lo dañará.

• No modifique los conectores del UPS y no utilice un adaptador que pueda eliminar la

conexión a tierra del sistema.

• No utilice cables de extensión para conectar el UPS a la toma de CA. Si se utiliza otro

tipo de supresor de sobretensión que no sea Tripp Lite para conectar el UPS a la toma de

corriente, se anulará la garantía del sistema.

• Si el sistema UPS recibe energía eléctrica por medio de un generador motorizado de CA,

éste deberá proporcionar una salida de corriente limpia y filtrada del tipo utilizado para las

computadoras.

Advertencias sobre la conexión del equipo

• No utilice los sistemas UPS de Tripp Lite en aplicaciones para el sostén de la vida

humana donde un fallo pudiera causar anomalías o alterar significativamente el

rendimiento del dispositivo del sostén de vida.

• No conecte supresores de sobretensión o cables de extensión a la salida del sistema UPS.

Esto podría dañarlo, así como al supresor de picos, e invalidar sus garantías.

Advertencias sobre las baterías

• El sistema UPS no requiere mantenimiento rutinario alguno. No abra el UPS por ningún

motivo, excepto para el reemplazo de las baterías. Esta unidad no contiene partes

interiores que puedan ser reparadas por el usuario.

• Sólo debe cambiar las baterías personal técnico debidamente capacitado. Debido a los

riesgos de choques eléctricos y quemaduras por la elevada corriente de los cortocircuitos

que presentan las baterías, el personal técnico capacitado debe observar todas las

precauciones pertinentes. Desconecte y apague el sistema UPS antes de reemplazar las

baterías. Utilice herramientas con asas aisladas y reemplace las baterías con el mismo

número y tipo de baterías nuevas (selladas de plomo y ácido). No abra las baterías. No

permita que ningún objeto entre en contacto con ambos bordes o terminales de las

baterías.

• Las baterías del sistema UPS son reciclables. Refiérase al reglamento local para

averiguar cómo deben desecharse o, en EE.UU. solamente, llame al 1-800-SAV-LEAD

para recibir información sobre el reciclaje. No utilice fuego para desechar las baterías.

• No agregue baterías externas al sistema UPS.

Importantes instrucciones de seguridad

GUARDE ESTAS INSTRUCCIONES

Este manual contiene advertencias e instrucciones importantes que deben seguirse

durante la instalación, operación y almacenamiento de todos los sistemas UPS de Tripp

Lite. De no cumplirse estas advertencias, la garantía será anulada.

200202076 93-2031 BC PRO600 Owner’s Manual.qxd 5/22/02 4:32 PM Page 10

Autres manuels pour BCPRO1400

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite UPS

Tripp Lite

Tripp Lite SmartOnline 20KVA Manuel utilisateur

Tripp Lite

Tripp Lite AGOM5516 Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro 450 RT Manuel utilisateur

Tripp Lite

Tripp Lite 500 VA Manuel utilisateur

Tripp Lite

Tripp Lite OMNISMART1400HG Instructions d'installation et d'utilisation

Tripp Lite

Tripp Lite SmartOnline Intelligent True On-Line UPS... Instructions d'installation et d'utilisation

Tripp Lite

Tripp Lite ECO750UPS Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART1000RM2U Manuel utilisateur

Tripp Lite

Tripp Lite 1250-3000 VA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART1500 Manuel utilisateur

Tripp Lite

Tripp Lite SM1000RMNAFTA Manuel utilisateur

Tripp Lite

Tripp Lite SMART1500CRMXL Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART500RT1U Manuel utilisateur

Tripp Lite

Tripp Lite SM750XLNAFTA Manuel utilisateur

Tripp Lite

Tripp Lite SUPDMB6KIEC Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline AGPS5548 Manuel utilisateur

Tripp Lite

Tripp Lite BC Personal Datashield BCPERS300 Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro SMART3000RMOD2U Manuel utilisateur

Tripp Lite

Tripp Lite SmartOnline SU1500RTXL2UA Manuel utilisateur

Tripp Lite

Tripp Lite SMART1500LCDXL Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro ST700HGL Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro 700 HG Instructions d'installation et d'utilisation

Tripp Lite

Tripp Lite SmartPro SMART3000RMXL2U Guide d'installation

Manuels UPS populaires d'autres marques

Pylontech

Pylontech Victron & Pylontech US5000 Manuel utilisateur

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuel utilisateur

Mecer

Mecer ME-1000-WTU Manuel utilisateur

Mustek

Mustek PowerMust 530(B) Plus Manuel d'installation et d'exploitation

Emerson

Emerson Liebert NXL series Manuel utilisateur

MAKELSAN

MAKELSAN BOXER SERIES Manuel utilisateur

Block

Block PC-0524-400-0 Manuel utilisateur

CyberPower

CyberPower CP585LCD Manuel utilisateur

Eaton

Eaton 3S Instructions de montage

CyberPower

CyberPower Office Tower Series UPS 1000 Manuel utilisateur

CyberPower

CyberPower BM100 Manuel utilisateur

Best Power

Best Power 610 Manuel utilisateur

Best Power

Best Power Unity/I UT3K Manuel utilisateur

Mustek

Mustek PowerMust 400 Offline Manuel utilisateur

Xantrex

Xantrex Trace 512 UR-UPS Manuel utilisateur

Forza

Forza SL-1501UL Manuel utilisateur

LEGRAND

LEGRAND keor 310081 Manuel utilisateur

ABB

ABB Conceptpower DPA 500 Manuel utilisateur