Tripp Lite SmartPro ST1000RM2UL Manuel utilisateur

Owner’s Manual

1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support

Important Safety Instructions 2

Connecting the Battery 4

Mounting 5

Quick Installation 7

Optional Installation 8

UPS Operating Modes 9

Basic Operation 10

Storage and Service 18

Product Registration 19

Español 20

Français 39

SmartPro®2U Rack-Mount

Intelligent, Line-Interactive UPS Systems

(with Lithium Iron Phosphate Batteries)

120V Sine Wave Output • 1,000VA

SMART1000RM2UL

(Series Number: AG-8898)

Not suitable for mobile applications.

PROTECT YOUR INVESTMENT!

and ultimate peace of mind.

You could also win an

ISOBAR6ULTRA surge protector—

a $100 value!

www.tripplite.com/warranty

18-05-315-933848.indb 1 7/9/2018 11:22:47 AM

Important Safety Instructions

SAVE THESE INSTRUCTIONS

This manual contains important instructions that should be followed during the installation,

operation and storage of this product. Failure to heed these warnings may affect the

warranty.

UPS Location Warnings

• Use caution when lifting the UPS. Because of the considerable weight of all rack-mount UPS

systems, at least two people should assist in lifting and installing them.

• Install the UPS indoors, away from excess moisture or heat, dust or direct sunlight.

• For best performance, the ambient temperature near the UPS should be between 0° C and 40° C

(between 32° F and 104° F).

• Leave adequate space around all sides of the UPS for proper ventilation. Do not obstruct its vents

or fan openings.

• When mounting the UPS system in a tower orientation, make sure the LCD panel is at the top of

the UPS, not at the bottom.

• Do not mount unit with its front or rear panel facing down (at any angle). Mounting in this manner

will seriously inhibit the unit’s internal cooling, eventually causing product damage not covered

under warranty.

UPS Connection Warnings

• The UPS contains its own energy source (battery). The output terminals may be live even when

the UPS is not connected to an AC supply.

• Connect the UPS to a properly grounded AC power outlet. Do not modify the UPS plug in a way

that would eliminate the UPS connection to ground. Do not use adapters that eliminate the UPS

connection to ground.

• Do not plug the UPS into itself; this will damage the UPS and void your warranty.

• If you are connecting the UPS to a motor-powered AC generator, the generator must provide

filtered, frequency-regulated computer-grade output. Connecting the UPS to a generator will void

its Ultimate Lifetime Insurance.

• Install in accordance with National Electrical Code standards ANSI/NFPA 70 and Canadian

Electrical Code, Part I, C22.1.

• Short Circuit backup protection and overcurrent protection is provided by the building installation.

• To reduce the risk of fire, connect only to a circuit provided branch circuit overcurrent protection

in accordance with the National Electrical Code, ANSI/NFPA 70 and the Canadian Electrical Code,

Part I, C22.1.

• The plug on the power supply cord is intended to serve as the disconnect device. Be sure that the

socket-outlet is installed near the equipment and is made easily accessible.

Caution! This UPS may receive power from more than one source. Disconnection of

the AC and DC sources is required to de-energize the unit before servicing.

Equipment Connection Warnings

• Use of this equipment in life support applications where failure of this equipment can reasonably

be expected to cause the failure of the life support equipment or to significantly affect its safety

or effectiveness is not recommended.

• Do not connect surge suppressors or extension cords to the output of the UPS. This might

damage the UPS and may affect the surge suppressor and UPS warranties.

18-05-315-933848.indb 2 7/9/2018 11:22:47 AM

Battery Warnings

• Batteries can present a risk of electrical shock and burn from high short-circuit current. Observe

proper precautions. Do not dispose of the batteries in a fire. Do not open the UPS or batteries.

Do not short or bridge the battery terminals with any object. Unplug and turn off the UPS before

performing battery replacement. Use tools with insulated handles. There are no user-serviceable

parts inside the UPS.

• DO NOT MIX INTERNAL LITHIUM ION BATTERIES WITH SEALED LEAD ACID BATTERIES.

• Do not operate the UPS without batteries.

• The UPS must be returned to Tripp Lite for battery replacement. Visit www.tripplite.com/support

and click the product returns link to request a Returned Material Authorization (RMA) number

(an RMA number is required for service). Once the product request information is completed, an

assigned RMA number and shipping instructions will be sent to your email account. See Storage

and Service for more information.

UPS and Battery Recycling

Please recycle Tripp Lite Products. The batteries used in these Tripp Lite products are

Lithium Iron Phosphate batteries. These batteries are highly recyclable. Please refer to your

local codes for disposal requirements.

You can call Tripp Lite for recycling info at 773.869.1234.

You can go the Tripp Lite Website for up-to-date information on recycling the batteries or any

Tripp Lite product. Please follow this link: http://www.tripplite.com/support/recycling-program/

Important Safety Instructions

18-05-315-933848.indb 3 7/9/2018 11:22:47 AM

Connecting the Battery

The UPS is shipped with the battery disconnected. The battery must be connected for the UPS to

operate. This should be done prior to connecting the UPS to AC mains or connecting any

equipment to the UPS. Follow the installation procedure below:

4 x screws 4 x screws

2Remove Battery Retention Plate

1Remove Front Panel

4 x screws

3Connect Batteries 4Replace Battery Retention Plate

5Replace Front Panel

18-05-315-933848.indb 4 7/9/2018 11:22:49 AM

Mounting (Rack)

Mount your equipment in either a 2-post or 4-post rack or rack enclosure. The user must

determine the fitness of hardware and procedures before mounting. If hardware and procedures

are not suitable for your application, contact the manufacturer of your rack or rack enclosure. The

procedures described in this manual are for common rack and rack enclosure types and may not

be appropriate for all applications.

Note: The illustrations may differ from your model.

4-Post Mounting

1The included plastic pegs Awill temporarily

support the empty rack-mount shelves B

while you install the permanent mounting

hardware. Insert a peg near the center of

the front and rear bracket of each shelf as

shown. (Each front bracket has 6 holes and

each rear bracket has 3 holes.) The pegs

will snap into place.

After installing the pegs, expand each shelf

to match the depth of your rack rails. The

pegs will fit through the square holes in the

rack rails to support the shelves. Refer to

the rack unit labels to confirm that the

shelves are level in all directions.

Note: The support ledge of each shelf must face

inward.

2Secure the shelves Bto the mounting rails

permanently using the included screws and

cup washers Cas shown. Place the cup

washer between the screw and the rack so

that the screw enters the wider opening of

the cup washer first.

Place 4 screws total at the front and 4

screws total at the back.

Tighten all screws before proceeding.

WARNING: Do not attempt to install your equipment until you have inserted and

tightened the required screws. The plastic pegs will not support the weight of your

equipment.

3Attach your equipment’s mounting brackets

to the forward mounting holes of the

cabinet using the hardware included with

your equipment. The mounting bracket

“ears” should face forward. (Some

equipment may have pre-installed or

integral mounting brackets.)

4With the aid of an assistant (if necessary),

lift your equipment and slide it into the

shelves. Attach the equipment mounting

brackets to the forward mounting rails with

user-supplied screws and washers D.

Tighten all screws securely.

18-05-315-933848.indb 5 7/9/2018 11:22:52 AM

Mounting (Rack)

2-Post Mounting/Wall Mounting

2-post mounting requires a Tripp Lite 2-Post Rack-Mount Installation Kit (model: 2POSTRMKITWM,

sold separately).

Wall mounting requires a Tripp Lite Wall Mount Kit 9 (2POSTRMKITWM, sold separately).

Mounting (Tower)

WARNING: When mounting the UPS system in a tower or wall-mount orientation, make sure

the LCD panel is at the top of the UPS, not at the bottom.

Note: To mount the UPS in an upright (tower) position, a 2-9USTAND is required (sold separately).

Rotate the LCD panel for easy viewing while the

UPS is tower mounted. Insert a small

screwdriver, or other tool, in the slots on either

side of the panel. Pop the panel out, rotate it

and pop the panel back in place.

18-05-315-933848.indb 6 7/9/2018 11:22:52 AM

Quick Installation

1Plug the UPS into an outlet on

a dedicated circuit.

Note: After you plug the UPS into a live AC outlet,

the UPS (in “Standby” mode) will automatically

charge its batteries, but will not supply power to

its outlets until it is turned ON.

2Plug your equipment into

the UPS.*

* Your UPS is designed to support only electronic

equipment. You will overload the UPS if the total

VA ratings for all the equipment you connect

exceeds the UPS’s Output Capacity. To find your

equipment’s VA ratings, look on its nameplates.

If the equipment is listed in amps, multiply the

number of amps by 120 to determine VA.

(Example: 1 amp × 120 = 120 VA). If you are

unsure if you have overloaded the UPS outlets,

see LOAD icon description in LCD Interface

section under Basic Operation.

3Turn the UPS ON.

Press and hold the button Afor one

second. The alarm will beep once briefly.

Note: UPS system will function properly upon

initial startup, however, maximum runtime for the

unit’s battery will only be accessible after it has

been charged for 24 hours.

18-05-315-933848.indb 7 7/9/2018 11:22:53 AM

USB

RS232

USB

RS232

USB

RS232

4-5

Optional Installation

These connections are optional. Your UPS will function properly without these connections.

1USB and RS-232 Serial

Communications

Use the included USB cable (see 1A) or

DB9 serial cable (see 1B) to connect the

communication port on your computer to

the communication port of your UPS. Install

on your computer the Tripp Lite PowerAlert

Software appropriate to your computer’s

operating system.

2EPO Port Connection

This optional feature is only for those

applications which require connection to a

facility’s Emergency Power Off (EPO) circuit.

When the UPS is connected to this circuit,

it enables emergency shutdown of the

UPS’s inverter.

Using the cable provided, connect the EPO

port of your UPS (see 2A) to a user-supplied

normally closed or normally open switch

according to the circuit diagram (see 2B).

The EPO port is not a phone line surge

suppressor; do not connect a phone line to

this port.

18-05-315-933848.indb 8 7/9/2018 11:22:55 AM

UPS Operating Modes

Standby Mode

(Charger: ON / AC Output: OFF / Battery Backup: NOT AVAILABLE)

When first connected to a live power source, the UPS will automatically energize into STANDBY

MODE. In this mode, the UPS charger will function as necessary to maintain full battery charge,

but there will be no AC output and no battery backup for connected equipment in the event of a

power failure. To turn the UPS on into LINE POWER MODE, press and hold the “ON/OFF” button for

one second until a beep is heard, and release.

Line Power Mode

(Charger: ON / AC Output: ON / Battery Backup: AVAILABLE)

The standard protected UPS operating mode for the UPS is LINE POWER MODE. In this mode, the

UPS provides voltage-regulated output sourced directly from the AC mains line power input. UPS

output power is conditioned with automatic voltage regulation in LINE POWER MODE to correct any

voltage fluctuations present on the mains line power input. When operating in LINE POWER MODE,

the UPS will automatically switch to BATTERY MODE during power failures or severe voltage

fluctuations to maintain connected equipment operation from battery reserves.

Battery Mode

(Charger: OFF / AC Output: ON / Battery Backup: ON)

BATTERY MODE is the automatic UPS response to mains AC power failures and severe voltage

fluctuations occurring when the UPS is operating in LINE POWER MODE. In BATTERY MODE, the

UPS is providing battery-derived AC output to connected equipment. When running in BATTERY

MODE, the UPS will automatically return to LINE POWER MODE when acceptable mains AC input is

restored to the UPS.

18-05-315-933848.indb 9 7/9/2018 11:22:55 AM

Note: This LCD image is shown

with all icons illuminated. Under

normal conditions, only select

icons will be lit.

Basic Operation

LCD Interface

3-Digit Display: This display is generally used to show values for a given

“Display” or “Control” screen.

“ON/OFF” Button

• To turn the UPS ON: After you plug the UPS into a live AC outlet, the UPS (in

“Standby” mode) will automatically charge its batteries, but will not supply

power to its outlets until it is turned ON. With the UPS plugged into a live AC

wall outlet, press and hold the “ON/OFF” button for one second.* The UPS

will beep once to indicate ON status. Release the button.

• To cold-start the UPS: If utility power is absent, you can “cold-start” the UPS

(i.e., turn it on and supply power for a limited time from its batteries) by

pressing and holding the “ON/OFF” button for one second.* The UPS will beep

once to indicate ON status. Release the button.

• To turn the UPS OFF: With the UPS ON and receiving utility power, press and

hold the “ON/OFF” button for 2.5 seconds.* The UPS will beep once to

indicate OFF status. Then unplug the UPS from the wall outlet. The UPS will

be completely off.

* If the user unintentionally presses the ON/OFF button, the OFF function can be

temporarily canceled by continuing to hold the ON/OFF button until the UPS beeps and

then, without releasing it, momentarily press either the MODE button or the ENTER/

MUTE button. Once both buttons are released, the UPS will remain ON.

“MODE” Button

To enable viewing of power displays and control menu options, tap this button.

See “Display Power Conditions” & “Control Menu Options” for details.

• Can be used in conjunction with the ON/OFF button to cancel the “OFF”

function. See “ON/OFF Button” instructions above.

• Can be used in conjunction with the “ENTER/MUTE” button to restore the LCD

to Factory Mode. See “Control Menu Options.”

18-05-315-933848.indb 10 7/9/2018 11:22:56 AM

Ce manuel convient aux modèles suivants

Table des matières

Langues :

Autres manuels Tripp Lite Support et étagère

Tripp Lite

Tripp Lite SmartRack SR1UCAGEREAR Manuel utilisateur

Tripp Lite

Tripp Lite DDR1327DCS Manuel utilisateur

Tripp Lite

Tripp Lite DDR1026MQ Manuel utilisateur

Tripp Lite

Tripp Lite N062-048-KJ Manuel utilisateur

Tripp Lite

Tripp Lite WWSSCOS26AM Manuel utilisateur

Tripp Lite

Tripp Lite DWT1323S Manuel utilisateur

Tripp Lite

Tripp Lite DMPDD1735AM Manuel utilisateur

Tripp Lite

Tripp Lite DWFPSC4570M Manuel utilisateur

Tripp Lite

Tripp Lite SmartRack Manuel utilisateur

Tripp Lite

Tripp Lite DMATC Manuel utilisateur

Tripp Lite

Tripp Lite DWT3763X Manuel utilisateur

Tripp Lite

Tripp Lite DWFSC3255MUL Manuel utilisateur

Tripp Lite

Tripp Lite DWF4585X Manuel utilisateur

Tripp Lite

Tripp Lite DDR1327DCS Manuel utilisateur

Tripp Lite

Tripp Lite Dual Flat Screen Desk Stand Manuel utilisateur

Tripp Lite

Tripp Lite DWM1737MA Manuel utilisateur

Tripp Lite

Tripp Lite SmartPro 1400 XL Manuel utilisateur

Tripp Lite

Tripp Lite DDR1327SDFC-1 Manuel utilisateur

Tripp Lite

Tripp Lite DWTPSC4555M Manuel utilisateur

Tripp Lite

Tripp Lite DMCS3270XP Manuel utilisateur

Tripp Lite

Tripp Lite SR2POST12 Manuel utilisateur

Tripp Lite

Tripp Lite WWSSFDSAM Manuel utilisateur

Tripp Lite

Tripp Lite DWM5070HD Manuel utilisateur

Tripp Lite

Tripp Lite DMPDS5570S Manuel utilisateur

Manuels Support et étagère populaires d'autres marques

Salamander

Salamander Acadia AC/W/L400/WH Manuel utilisateur

Fohhn

Fohhn VAT-09 Guide de l'utilisateur

ricoo

ricoo FS0522 Manuel utilisateur

AMSOIL

AMSOIL BMK-22 Guide rapide

Kargo Master

Kargo Master 48220 Manuel utilisateur

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuel utilisateur

ricoo

ricoo S1222 Manuel utilisateur

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuel utilisateur

VidaBox

VidaBox VB MNT FFS2 Manuel utilisateur

Welch Allyn

Welch Allyn 48960 Manuel utilisateur

Arkon

Arkon CM035-ST-2 Manuel utilisateur

PROEL

PROEL PLWIN60C Manuel utilisateur

Agilent Technologies

Agilent Technologies E2609B Manuel utilisateur

Mustang

Mustang MV-ARM4 Manuel utilisateur

Mounting Solutions

Mounting Solutions WRM-320 Manuel utilisateur

Pyle

Pyle PMKSPAD1 Manuel utilisateur

ShelterIt

ShelterIt 21208 Manuel utilisateur

SPL

SPL RackPack?4 1040 Manuel utilisateur