Tripp Lite B130-101A-MR Manuel utilisateur
1
Owner’s Manual
VGA Over Cat5 Extenders
and Extender/Splitters
Extender Kit Models:
B130-101A-MR and B130-101A-SR
Transmitter Unit Models:
B132-002A-2 and B132-004A-2
Receiver Unit Models:
B132-100A-MR, B132-100A-SR and B132-200A-SR
1111 W. 35th Street, Chicago, IL 60609 USA • www.tripplite.com/support
Copyright © 2015 Tripp Lite. All rights reserved.
All trademarks are the sole property of their respective owners.
15-04-118-9333BE.indd 1 4/8/2015 10:35:08 AM
2
Package Contents
B130-101A-MR
B130-101A-SR
B132-002A-2
B132-004A-2
B132-100A-MR
B132-100A-SR
B132-200A-SR
Local Unit (L), Remote Unit (R) or Both (B) B B L L R R R
External Power Supply (P) or Micro USB Cable (U) U U P P U U P
Number of Power Supplies / Micro USB Cables 2 2 1 1 1 1 1
Mounting Hardware Y Y
Screwdriver Y Y Y Y Y
1-ft. VGA + Audio Daisy Chain Cable Y
Table of Contents
Package Contents 2
Product Features 3
All 3
B130-101A-MR 3
B130-101A-SR 3
B132-002A-2 3
B132-004A-2 4
B132-100A-MR 4
B132-100A-SR 5
B132-200A-SR 5
Optional Accessories 5
Mounting Hardware 6
Instructions
Installation 7
EDID Copy 7
Extender Kit Installation 9
Non-Kit Standard Installation 11
Non-Kit Daisy Chain Installation 13
Troubleshooting 16
Warranty and Product 18
Registration
Additional Warnings and 19
Notices
15-04-118-9333BE.indd 2 4/8/2015 10:35:09 AM
3
Product Features
All
• Transmits both VGA video and mono audio.
• All operating systems supported.
• Plug and play; no software or drivers required.
• HDCP compliant.
B130-101A-MR
• Extends a 1920 x 1080 video signal up to 300 ft. or a 1024 x 768
video signal up to 750 ft.
• Receiver unit features built-in equalization and gain controls to adjust
the video image.
• Power is supplied via the Micro USB ports on the transmitter and
receiver units. No external power supplies required.
• EDID copy feature ensures optimal display compatibility.
B130-101A-SR
• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video
signal up to 300 ft.
• Receiver unit features built-in equalization and gain controls to adjust
the video image.
• Power is supplied via the Micro USB ports on the transmitter and
receiver units. No external power supplies required.
• EDID copy feature ensures optimal display compatibility.
B132-002A-2
• Works with the B132-100A-MR, B132-100A-SR and B132-200A-SR
remote units to extend both the VGA video and audio signal.
• Transmits a single VGA video and audio signal to 2 sets of monitors and
speakers.
• Includes mounting hardware that allows unit to be wall-mounted, rack
mounted or pole mounted.
• EDID copy feature ensures optimal display compatibility.
15-04-118-9333BE.indd 3 4/8/2015 10:35:09 AM
4
B132-004A-2
• Works with the B132-100A-MR, B132-100A-SR and B132-200A-SR
remote units to extend both the VGA video and audio signal.
• Features additional VGA and 3.5 mm ports for connecting a local
monitor and speakers.
• Transmits a single VGA video and audio signal to up to 5 sets
(4 remote, 1 local) of monitors and speakers.
• Expands the number of connected monitors/speakers up to 25
(24 remote, 1 local) by daisy chaining up to 6 local units together.
Note: B132-002A-2 local units cannot be daisy chained.
• Includes mounting hardware that allows unit to be wall-mounted, rack
mounted or pole mounted.
• Up to three local units can be connected to a Tripp Lite B132-004-RB
rackmount bracket and mounted in just 1U of rack space.
• EDID copy feature ensures optimal display compatibility.
B132-100A-MR
• Works with the B132-002A-2 and B132-004A-2 transmitter units to
extend a VGA video and audio signal.
• Extends a 1920 x 1080 video signal up to 300 ft. or a 1024 x 768
video signal up to 750 ft.
• Features built-in equalization and gain controls to adjust the video
image.
• Power is supplied via a Micro USB port. No external power supply
required.
Product Features continued
15-04-118-9333BE.indd 4 4/8/2015 10:35:09 AM
5
Product Features continued
B132-100A-SR
• Works with the B132-002A-2 and B132-004A-2 transmitter units to
extend a VGA video and audio signal.
• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video
signal up to 300 ft.
• Features built-in equalization and gain controls to adjust the video
image.
• Power is supplied via a Micro USB port. No external power supply
required.
B132-200A-SR
• Works with the B132-002A-2 and B132-004A-2 transmitter units to
extend a VGA video and audio signal.
• Features two sets of VGA and audio ports to connect two sets of
monitors and speakers.
• Extends a 1440 x 900 video signal up to 150 ft. or a 1024 x 768 video
signal up to 300 ft.
• Features built-in equalization and gain controls to adjust the video
image.
Optional Accessories
• B132-004-RB 1U Rackmount Bracket
• N022-01K-GY Gray Cat5e Bulk 24 AWG Solid Cable – 1,000 ft.
• N030-010 10-pack of RJ45 Plugs for Solid-wire Cat5e Cable
• N202-Series Cat6 Snagless 24 AWG Solid Patch Cables
• N222-01K-GY Gray Cat6 Bulk 24 AWG Solid Cable – 1,000 ft.
• P312-Series Audio Cables
• P502-Series VGA Monitor Cables with RGB Coax
• P504-Series VGA Monitor + Audio Cables with RGB Coax
• P524-01K Zero-Skew UTP Bulk Cable – 1,000 ft.
15-04-118-9333BE.indd 5 4/8/2015 10:35:09 AM
6
Mounting Hardware Instructions
The B132-002A-2 and B132-004A-2 units come with mounting
hardware that allows them to be mounted in a variety of ways. The
following images show the different ways the included mounting brackets
can be attached for different mounting methods.
Note: The images below show a B140-101X DVI Extender, but mounting is the
same for the VGA Extenders. The B132-004A-2 can also be mounted to a Tripp Lite
B132-004-RB 1U rackmount bracket. Up to three B132-004A-2 local units can be
connected to a B132-004-RB.
Wall-Mount 1 Wall-Mount 2
19” Rack Mount Pole Mount
15-04-118-9333BE.indd 6 4/8/2015 10:35:10 AM
7
Installation
EDID Copy
Compatibility issues can occur when EDID information is not properly
communicated between the source and the display. All of the transmitter
units in this manual include an EDID copy feature which stores a
monitor’s EDID information in the transmitter and sends it to the source,
ensuring optimal compatibility.
The transmitter can only store EDID information copied from a single
monitor. You should copy the EDID information of the monitor that
has the lowest maximum supported resolution of all monitors being
connected. This monitor must also support the native video resolutions of
the other monitors.
For example, if you plan to use three monitors that support the
resolutions listed below, you should copy the EDID information from
Monitor A, since the highest resolution it supports is 1440 x 900, which
is lower than the highest supported resolutions of the other two monitors.
Monitor A’s supported resolutions are also supported by Monitors B and C.
A. 1440 x 900, 1024 x 768, 800 x 600
B. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1024 x 768, 800 x 600
C. 1920 x 1080, 1680 x 1050, 1600 x 1200, 1280 x 768, 1152 x 768,
1024 x 768, 800 x 600
If you are not using the EDID copy feature, the transmitter will use a
default set of EDID information.
Note: Receiver units will support EDID copy as long as they are used with a
transmitter unit that supports it.
To use the EDID copy feature, follow the instructions below:
1Determine which monitor to perform EDID copy on, per the example
in the EDID Copy section above.
2If using a B132-002A-2 or B132-004A-2 model, connect the
powered-on monitor to the input port of the transmitter unit. For the
B130-101A-MR and B130-101A-SR, connect the built-in VGA cable
on the transmitter unit to the powered-on monitor.
15-04-118-9333BE.indd 7 4/8/2015 10:35:10 AM
8
3If using a B132-002A-2 or B132-004A-2 model, connect the
external power supply to the unit and plug it into a Tripp Lite Surge
Protector, Power Distribution Unit (PDU) or Uninterruptible Power
Supply (UPS). For the B130-101A-MR and B130-101A-SR models,
connect the included Micro USB cable to the unit and plug it into the
USB port on a computer or a USB wall outlet. Wait 10 seconds for
the EDID information to be copied, then disconnect the monitor and
proceed per the installation instructions in this manual.
Note: The B130-101A-MR and B130-101A-SR transmitter units feature an internal
EDID LED that blinks to indicate a scan is taking place. The LED will stop blinking
and glow solid when the scan is complete. When a monitor is connected, its EDID
information will be copied and stored on the transmitter unit. If no monitor is
connected, the scan will still take place and the Orange LED will illuminate, but no
EDID information will be copied. The information stored on the transmitter unit will
remain unchanged.
4You can verify that the EDID information was copied from your
computer’s Display Settings screen. If the model name of the monitor
that you copied is shown in the Display field, the EDID information
has been copied successfully.
Note: You may need to click on the Detect button.
Installation continued
15-04-118-9333BE.indd 8 4/8/2015 10:35:10 AM
9
Extender Kit Installation
(B130-101A-MR and B130-101A-SR)
Note:
1. If desired, perform the EDID copy procedure described in this manual prior to
installation.
2. Test to make sure the entire installation works properly before pulling cables
through ceilings/walls.
3. To achieve maximum distance and performance, 24 AWG solid-wire Cat5e/6
cable must be used. The use of stranded wire Cat5e/6 cable, or cable with a
gauge (AWG) size higher than 24 AWG will result in shorter extension distance.
All Tripp Lite N202-Series cables are made with 24 AWG solid-wire cabling.
Tripp Lite N022-01K-GY (Cat5e) and N222-01K-GY (Cat6) are 24 AWG solid-wire
bulk cables. For optimal image quality, use Zero-Skew cable such as Tripp Lite
P524-01K.
1Make sure the VGA and audio source is powered off.
2Connect the built-in VGA cable of the transmitter unit to the
computer’s VGA port.
3Connect a 3.5 mm audio cable from the transmitter unit to the
computer.
4Connect the included Micro USB cable between the transmitter unit
and a USB port on the computer or USB wall outlet.
5Using Cat5e/6 cable, connect the RJ45 OUTPUT port of the
transmitter unit to the RJ45 INPUT port of the receiver unit (see
Product Features section for your model’s max distance information).
6Connect the built-in VGA cable of the receiver unit to the monitor’s
VGA port.
Installation continued
Transmitter Unit Receiver Unit
15-04-118-9333BE.indd 9 4/8/2015 10:35:10 AM
10
Installation continued
7Connect a 3.5 mm audio cable from the receiver unit to the monitor
or external speakers.
8Use the included Micro USB cable to connect the receiver unit with a
USB port on the monitor or USB wall outlet.
9Turn on the power to the computer, monitor and speakers.
10 If necessary, adjust the equalization and gain controls on the receiver
unit with the included screwdriver to improve the video image.
15-04-118-9333BE.indd 10 4/8/2015 10:35:10 AM
Ce manuel convient aux modèles suivants
6
Table des matières
Autres manuels Tripp Lite Extenseur
Tripp Lite
Tripp Lite B127A-4X1-BH Manuel utilisateur
Tripp Lite
Tripp Lite B127-1A1-HH Manuel utilisateur
Tripp Lite
Tripp Lite B162-100-POE Manuel utilisateur
Tripp Lite
Tripp Lite B150-1A1-DVI Manuel utilisateur
Tripp Lite
Tripp Lite U007-40M Manuel utilisateur
Tripp Lite
Tripp Lite B125-101-60-WP Manuel utilisateur
Tripp Lite
Tripp Lite B120-000-SL Manuel utilisateur
Tripp Lite
Tripp Lite B132-100A Manuel utilisateur
Tripp Lite
Tripp Lite B127-008-D Manuel utilisateur
Tripp Lite
Tripp Lite B120-000-SL Manuel utilisateur
Tripp Lite
Tripp Lite B132-100A Manuel utilisateur
Tripp Lite
Tripp Lite B136-101 Manuel utilisateur
Tripp Lite
Tripp Lite B164-101-WIR Manuel utilisateur
Tripp Lite
Tripp Lite B126-004 Manuel utilisateur
Tripp Lite
Tripp Lite BHDBT-K-SI Manuel utilisateur
Tripp Lite
Tripp Lite B127A-1A1-BHBH Manuel utilisateur
Tripp Lite
Tripp Lite B125-101-60-IR Manuel utilisateur
Tripp Lite
Tripp Lite B125-150 Manuel utilisateur
Tripp Lite
Tripp Lite B203-101 Manuel utilisateur
Tripp Lite
Tripp Lite P167-000 Manuel utilisateur
