Trikdis E14 Manuel utilisateur

www.trikdis.lt UAB Trikdis Draugystės g. 17, LT-51229 Kaunas, Lietuva +370 37 408 040 info@trikdis.lt

Ethernet communicator E14

USER MANUAL

July, 2018

www.trikdis.com 2July, 2018

Ethernet communicator E14

Contents

SAFETY REQUIREMENTS......................................................................................................................................................... 3

1DESCRIPTION ................................................................................................................................................................ 4

1.1 List of Compatible Control Panels................................................................................................................................ 4

1.2 Technical Parameters.................................................................................................................................................. 5

1.3 Terminal block description .......................................................................................................................................... 5

1.4 Light indication............................................................................................................................................................ 5

1.5 System overview ......................................................................................................................................................... 6

1.6 Package Contents........................................................................................................................................................ 6

2. CONNECT E14 TO TRIKDISCONFIG ................................................................................................................................. 6

2.1 Add communicator in Protegus......................................................................................Error! Bookmark not defined.

2.2 Communication settings with ARC .............................................................................................................................. 8

3. PHYSICAL INSTALLATION............................................................................................................................................... 9

3.1 Wire communicator to panel ...................................................................................................................................... 9

3.1.1 For UTC Interlogix (Caddx) control panels program the following settings........................................................... 10

3.2 (Optional) input connection ...................................................................................................................................... 11

3.3 Connect LAN cable .................................................................................................................................................... 11

3.4 (Optional) output connection.................................................................................................................................... 11

4. ADD COMMUNICATOR IN PROTEGUS ......................................................................................................................... 12

4.1 Additional settings for ARM/DISARM the system via keyswitch zone. ...................................................................... 12

4.2 System management with Protegus ......................................................................................................................... 14

5. CONNECT E14 TO TRIKDISCONFIG ............................................................................................................................... 14

6. SET OPERATION PARAMETERS.................................................................................................................................... 16

6.1 Status bar description ............................................................................................................................................... 16

6.2 System settings window............................................................................................................................................ 17

6.3 Reporting window → ARC reporting tab ................................................................................................................... 18

6.4 Reporting window → Protegus service tab ............................................................................................................... 18

6.5 Event Summary window............................................................................................................................................ 19

6.6 Reset factory settings................................................................................................................................................ 20

7. PERFORM SYSTEM TEST.............................................................................................................................................. 20

8. MANUAL FIRMWARE UPDATE .................................................................................................................................... 20

www.trikdis.com 3July, 2018

Ethernet communicator E14

Safety Requirements

The security alarm system should be installed and maintained by qualified personnel.

Prior to installation, please read carefully this manual in order to avoid mistakes that can lead to

malfunction or even damage to the equipment.

Disconnect power before making any electrical connections.

Changes, modifications or repairs not authorized by the manufacturer shall void your rights under the

warranty.

Please act according to your local rules and do not dispose of your unusable alarm system or its

components with other household waste.

www.trikdis.com 4July, 2018

Ethernet communicator E14

1Description

Communicator E14 is intended to upgrade compatible intruder alarm panels for event signalling via wired

Internet (Ethernet).

Customers are informed about security system events in Protegus app. Communicator can Arm/Disarm

the alarm system via keyswitch zone.

Communicator transmits full event information to Alarm Receiving Centre.

Features

Connection

Direct connection to supported panels for

quick installation and event reporting.

Communications

Simultaneous event reporting to Protegus

Mobile/Web application, allowing user to

remotely monitor and control his alarm

system

Integration with any monitoring software

with Trikdis receivers supporting Surgard

SG-MLR2 protocol

Can send events to universal DC-09

receivers

In case of lost connection with the main IP

address, switches automatically to backup

IP address

Communication in secure encrypted

protocol

Configuration

Quick and easy installation

Remote configuration and firmware

updates

Two access levels for setting of operating

parameters

1.1 List of Compatible Control Panels

Manufacturer

Model

DSC®

PC1616, PC1832, PC1864 PC585, PC1565, PC5020

PARADOX®

SPECTRA SP5500, SP6000, SP7000, 1727, 1728, 1738

MAGELLAN MG5000, MG5050

DIGIPLEX EVO48, EVO192, EVO96, NE96

ESPRIT E55, 728ULT, 738ULT

UTC Interlogix®

NetworX (Caddx) NX-4v2, NX-6v2, NX-8v2, NX-8e

Pyronix®

MATRIX 424, MATRIX 832, MATRIX 832+, MATRIX 6, MATRIX 816

GE Caddx

NX-4, NX-6, NX-8

Secolink

PAS8XX

www.trikdis.com 5July, 2018

Ethernet communicator E14

1.2 Technical Parameters

Parameter

Description

Power supply voltage

10-16 V DC

Current consumption

120 mA (stand-by)

Up to 250 mA (transmitting)

Ethernet connection

IEEE802.3, 10 Base-T, RJ45 socket

Data pack content

Contact ID format codes

Memory

Up to 100 messages

Inputs

2, NC/NO/EOL-2,2 kΩ type

Output

1 OC type, commutating voltage up to 30 V and current up to 500 mA

Operating environment

From -10 °C to 50 °C, with relative air humidity 80% when +20 °C

Dimensions

88 x 62 x 26 mm

1.3 Terminal block description

Contact

Description

+DC

power supply terminal (10-16 V DC positive terminal)

-DC

power supply terminal (10-16 V DC negative terminal)

CLK

Synchronizing signal clamp

DATA

Data signal clamp

IN1

1st input clamp (selectable type)

COM

Common (negative)

IN2

2nd input clamp (selectable type)

OUT

Out terminal (OC type), current up to 500 mA

A RS485

RS485 Bus A contact

B RS485

RS485 Bus B contact

1.4 Light indication

LED

Operation

Description

“Network” displays the

status of connection to the

Internet

Green ON

Communicator is connected to the Internet

Yellow ON

TCP/IP session is open

“Data” displays data transfer

Green ON

Unsent messages present

Red ON

Messages cannot be sent

Green flashing

Messages are being received from the control

panel

Green flashing

Power supply is sufficient,

www.trikdis.com 6July, 2018

Ethernet communicator E14

LED

Operation

Description

“Power” displays power

supply status and the

functioning of the

microprocessor

Yellow flashing

Power supply is not sufficient (≤11,5 V),

“Trouble”

Red ON

Computer network connectivity problems

No flashing/ No

light up

Works without problems

1.5 System overview

1.6 Package Contents

Communicator E14

1 pc.

2. Connect E14 to TrikdisConfig

1. Download TrikdisConfig from www.trikdis.com (in search field type TrikdisConfig), and install it.

2. Remove the E14 cover by using a flat screwdriver as shown below:

Note:

Before configuration, make sure you have all the necessary components:

1) USB Mini-B cable is required for configuration.

2) „CAT-5 Ethernet“ cable (maximum 100 m in length).

3) At least 4 wired cable to connect communicator to the security alarm system.

4) CRP2 cable to connect communcicator to the Paradox control panel‘s Serial Port.

5) Flat screwdriver.

6) User Manual for control panel to which Trikdis communicator will be connected.

Missing components order separately from your local distributor.

www.trikdis.com 7July, 2018

Ethernet communicator E14

3. Connect E14 to your computer via USB Mini-B cable.

4. Run the configuration software TrikdisConfig. The software will automatically recognise E14 and will

open a window for communicator configuration.

Click Read [F4] to read the communicators parameters and enter the Administrator or Installer code

in the pop-up window.

Note:

Click Read [F4] to scan and show settings that are recorded on the device.

Press Write [F5] to save settings on the screen to the device.

Click Save [F9] to save settings to the configuration file, which you can then upload to other

devices. This allows you quickly configure several products with the same settings.

Click Open [F8] and browse your computer to find the configuration file to set up the

communicator from a saved configuration file.

To restore the factory settings, press Restore button at the bottom left of the window.

2.1 Communication settings with Protegus

In the “System Settings” window:

1) Select Panel type that will be connected to the communicator.

In the window “Reporting”tab “Protegus Service”:

www.trikdis.com 8July, 2018

Ethernet communicator E14

2) Check Enable connection in Protegus service checkbox.

3) Change the Service code for logging in to Protegus, if you want to ask users to add it by adding the

Protegus system in the application (factory default - 123456).

More about other TrikdisConfig E14 settings see 6 " Set operation parameters ".

2.2 Communication settings with ARC

In the “System Settings” window:

1) Enter Account Number.

2) Select Panel type that will be connected to the communicator.

In the window "Reporting", tab "ARC Reporting" primary communication channel:

3) Enable –enable primary communication channel.

4) Remote host –enter receiver IP address.

5) Remote port –enter the receiver port number on the network.

6) TCP or UDP –select which protocol (TCP or UDP) should be sent messages.

www.trikdis.com 9July, 2018

Ethernet communicator E14

7) PING Time –PING signal transmission period.

8) Encryption key –enter encryption key that is set in the receiver.

9) (Recommended) Configure the Backup Channel Settings.

10)TCP protocol –select which encoding protocol will be use: TRK (for TRIKDIS receivers), DC-09_2007

or DC-09_2012 (for universal receivers).

11)Encryption enabled –select protocol

12)DC-09 encryption key –enter encryption key that is set in the receiver.

13)DC-09 receiver No. - –enter receiver number.

14)DC-09 line No. –enter receiver line number.

If you selected DC-09 message transmission encoding, in addition in the „Send to ARC“ window, on the

Settings tab, enter the object, line and receiver numbers.

In the window “Reporting” tab “Protegus Service”:

15)Check Enable connection in Protegus service checkbox.

16)Change the Service code for logging in to Protegus, if you want to ask users to add it by adding the

Protegus system in the aplicacion (factory default - 123456).

More about other TrikdisConfig E14 settings see 6 " Set operation parameters ".

3. Physical installation

3.1 Wire communicator to panel

Following the provided schematics connect the communicator to the control panel.

www.trikdis.com 10 July, 2018

Ethernet communicator E14

Important:

In Protegus app one PGM output can be assigned to control one Area (1 PGM - 1 Area; 2

PGM - 2 Areas) regardless of how many areas are controlled by same keyswitch zone in

panel.

Set which Area will be controlled by Protegus in system Settings. There select the checkbox

Arm/Disarm with PGM1, and the number of Area, which you want to control.

In Protegus Areas window, you will see all areas available in the system, with controllable

areas highlighted.

3.1.1 For UTC Interlogix (Caddx) control panels program the following settings

In order for communicator E14 to work with Caddx security control panels NX-4v2, NX-6v2, NX-8v2, NX-8e,

control panels` locations 23 and/or 37 must be set as shown in the table below. When there are more than

one partition in NX-8v2, NX-8e, also program locations 90, 93, 99, 102, 105, 108.

To enter program mode by default:

1. Press [*8 9713] and enter device number (by default 0).

2. Using control panel`s installation manual, set locations and features of segment.

Table des matières

Autres manuels Trikdis Téléphone portable

Trikdis

Trikdis G10D Manuel utilisateur

Trikdis

Trikdis E16T Manuel utilisateur

Trikdis

Trikdis G17F Manuel utilisateur

Trikdis

Trikdis G10T Manuel utilisateur

Trikdis

Trikdis G16T Manuel utilisateur

Trikdis

Trikdis G16T 3 Series Manuel utilisateur

Trikdis

Trikdis G16 Manuel utilisateur

Trikdis

Trikdis E10Tv2 Manuel utilisateur

Trikdis

Trikdis G10 Manuel utilisateur

Trikdis

Trikdis G16 Manuel utilisateur

Trikdis

Trikdis G16T Manuel utilisateur

Trikdis

Trikdis FireCom Manuel utilisateur

Trikdis

Trikdis G10 Manuel utilisateur

Trikdis

Trikdis G17F Manuel utilisateur

Trikdis

Trikdis GET Manuel utilisateur

Trikdis

Trikdis E10T Manuel utilisateur

Trikdis

Trikdis Ethernet E16 Manuel utilisateur

Trikdis

Trikdis G09 Manuel utilisateur

Trikdis

Trikdis G16T Manuel utilisateur

Manuels Téléphone portable populaires d'autres marques

Zte

Zte BLADE A520 Manuel utilisateur

Nokia

Nokia Lumia 620 Manuel utilisateur

Blackbe;rry

Blackbe;rry KEYone Manuel utilisateur

Bea-fon

Bea-fon X5 Premium Manuel utilisateur

Blackbe;rry

Blackbe;rry 8707 Series Manuel utilisateur

Blackbe;rry

Blackbe;rry Storm Mode d'emploi

LG LM-X420QN Manuel utilisateur

LifeWatch

LifeWatch V Manuel utilisateur

Bea-fon

Bea-fon SILVER LINE SL860 Manuel utilisateur

IKI Mobile

IKI Mobile KF4.5i Manuel utilisateur

Hitech

Hitech HT-850 Manuel utilisateur

Yezz

Yezz Fashion F10 Manuel utilisateur

Point Mobile

Point Mobile PM60 Manuel utilisateur

Blackbe;rry

Blackbe;rry Q10 Manuel utilisateur

Blackbe;rry

Blackbe;rry Bold 9900 Manuel utilisateur

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Manuel utilisateur

LG LM-K420EMW Manuel utilisateur

ISAFE MOBILE

ISAFE MOBILE IS655.2 Manuel utilisateur