TRENDnet TEW-740APBO Manuel utilisateur

TEW-740APBO

Quick Installation Guide

Table of Content

1 English

1. Before You Start

2. Hardware Configuration

3. Hardware Installation

1. Before You Start

Package Contents

ŸTEW-740APBO

ŸCD-ROM (User's Guide)

ŸQuick Installation Guide

ŸProprietary PoE injector

ŸPower adapter (48 V DC, 0.5 A)

ŸMounting Hardware

ŸWaterproof RJ-45 plug (network cable is not included)

ŸGrounding wire

Minimum Requirements

ŸComputer with a network port and web browser

ŸA network switch or router with an available network LAN port

Ÿ2 x RJ-45 network cables (sold separately)

ŸPhillips screwdriver (sold separately)

Note:

1. The TEW-740APBO does not support IEEE 802.3at/af. You must use the proprietary Power

over Ethernet injector that is supplied with the TEW-740APBO.

2. Check package contents for waterproof kit (network cable is not included).

Cable Gland Seal Claw Sealing Nut

2. Hardware Installation

Phase 1: Overview

Note: The default IP address of the TEW-740APBO is 192.168.10.100. To configure the

TEW-740APBO, your network adapter must have an IP address within the 192.168.10.x subnet

(e.g. 192.168.10.50). Please refer to the Appendix in the User's Guide for more information.

1. Write the MAC address (MAC1) of the two TEW-740APBOs. The MAC address (MAC1) can be

found on the side of the unit. In this example, we will assume the following:

TEW-740APBO #1 MAC Address: 00:11:22:00:00:11

TEW-740APBO #2 MAC Address: 00:11:22:00:11:22

Note:

1. The initial configuration should be completed in a testing environment with two

TEW-740APBO's approximately 15 ft. (5 meters) apart from one another.

2. Configure and connect the devices before mounting.

WDS Setup

Included PoE injector

1. Connect one end of a network cable into TEW-740APBO #1.

2. Connect the opposite end of the network cable to the P+DATA OUT port on the Power over

Ethernet Injector.

3. Connect one end of another network cable to the 10/100 DATA IN port on the Power over

Ethernet Injector.

4. Connect the other end of a network cable to your computer's Ethernet port.

5. Connect the power adapter into the Power over Ethernet Injector. Then connect the power

adapter into a power outlet. (EU models have an on/off switch. Please move the power switch

to the “On” position).

6. Assign a Static IP address to your computer's network adapter in the subnet of 192.168.10.x

(e.g. 192.168.10.50) and a subnet mask of 255.255.255.0.

7. Open your web browser, type the IP address of the access point in the address bar, and then

press Enter. The default IP address is 192.168.10.100

8. Power on the outdoor access point.

9. Login to the browser configuration page.

10. Change the administrator password.

11. Assign a valid IP address to the access point within the subnet defined by the router. Avoid

using an IP address within the DHCP pool of your router. In this example, we will assume

the following:

Router IP Address: 192.168.10.1

Subnet Mask: 255.255.255.0

DHCP Pool: 192.168.10.100~192.168.10.149

The TEW-740APBO will be setup with the following IP address assignment:

TEW-740APBO #1

IP Address: 192.168.10.50

IP Netmask (Subnet Mask): 255.255.255.0

IP Gateway (Gateway IP Address): 192.168.10.1

Primary DNS: 192.168.10.1

TEW-740APBO #2

IP Address: 192.168.10.51

IP Netmask (Subnet Mask): 255.255.255.0

Gateway IP Address: 192.168.10.1

Primary DNS: 192.168.10.1

12. Enable WDS mode.

13. Enable WPA2-PSK AES encryption and configure a wireless password for the access point.

14. Enter the MAC address of the other outdoor access point.

15. Repeat the process for the second outdoor access point.

18. Enter a new admin password.

19. Confirm the new password.

20. Click Save.

21. Please wait while the access point reboots.

Note: Username and password are case sensitive.

16. Confirm connectivity between the two access points.

17. Enter the default username and password, and then click Log In.

Note: For first time installation, you are required to change the admin password.

User Name: admin

Password: admin

29. Click System → Operating Mode.

30. Select WDS Mode and then click Save & Reboot.

System

LAN

Operating Mode

Save & Reboot

31. Please wait while the access point reboots.

System is restarting,

please wait for 50

seconds

22. Enter your new username and the new password, and then click Log In.

23. Click System → LAN.

24. Select Static IP.

25. Configure the IP address, IP Netmask, and IP Gateway based on the example in Phase 1:

Overview.

26. Select Specify DNS Server IP.

27. Configure the Primary DNS based on the example in Phase 1: Overview.

28. Click Save.

33. Click Wireless → WDS.

Note: To protect your network from any unauthorized access it is recommended to enable

wireless encryption.

34. Enter the MAC address of the other access point. The below configuration will be based on

the example in Phase 1: Overview.

32. Enter the username and password, and then click Log In.

Wireless

WDS

AES

password

Save

36. Click Reboot.

37. Repeat steps 2-27 for TEW-740APBO #2.

1. Leave TEW-740APBO #2 connected to your computer.

2. Connect TEW-740APBO #1 to a LAN port of a router on your network.

3. To verify connectivity, run your computer's command prompt and ping TEW-740APBO #1's

assigned IP address from your computer.

4. A successful ping reply determines that both TEW-740APBOs are configured properly and

connected.

Phase 3: Confirm Connectivity

Reboot

35. Click Reboot.

Reboot

Autres manuels pour TEW-740APBO

Table des matières

Autres manuels TRENDnet Point d'accès sans fil

TRENDnet

TRENDnet TEW-841APBO Manuel utilisateur

TRENDnet

TRENDnet TPL-310AP Manuel utilisateur

TRENDnet

TRENDnet TEW-413APBO Manuel utilisateur

TRENDnet

TRENDnet TEW-738APBO Manuel utilisateur

TRENDnet

TRENDnet TEW-821DAP Manuel utilisateur

TRENDnet

TRENDnet TEW-715APO Manuel utilisateur

TRENDnet

TRENDnet N300 TEW-739APBO Manuel utilisateur

TRENDnet

TRENDnet TEW-450APB - Wireless Super G Access Point Guide d'installation

TRENDnet

TRENDnet TEW-230APB Manuel utilisateur

TRENDnet

TRENDnet TEW-230APB Manuel utilisateur

TRENDnet

TRENDnet TEW-750DAP Manuel utilisateur

TRENDnet

TRENDnet TPL-410AP Manuel utilisateur

TRENDnet

TRENDnet TEW-650AP Manuel utilisateur

TRENDnet

TRENDnet TEW-825DAP(V1) Manuel utilisateur

TRENDnet

TRENDnet TEW-430APB - Wireless Access Point Manuel utilisateur

TRENDnet

TRENDnet TEW-740APBO Manuel utilisateur

TRENDnet

TRENDnet TEW-670AP Manuel utilisateur

TRENDnet

TRENDnet TEW-809UB(V1) Manuel utilisateur

TRENDnet

TRENDnet TEW-610APB Manuel utilisateur

TRENDnet

TRENDnet TEW-610APB Manuel utilisateur

TRENDnet

TRENDnet TEW-455APBO - 9dBi High Power Wireless Outdoor PoE Access... Manuel utilisateur

TRENDnet

TRENDnet TEW-653AP Manuel utilisateur

TRENDnet

TRENDnet TEW-690AP Manuel utilisateur

TRENDnet

TRENDnet TEW-815DAP Manuel utilisateur

Manuels Point d'accès sans fil populaires d'autres marques

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuel utilisateur

Ubiquiti

Ubiquiti NanoStation NSM2 Manuel utilisateur

Cisco

Cisco Aironet 1550 Series Manuel utilisateur

Aruba

Aruba IAP-335 Manuel utilisateur

Advantek Networks

Advantek Networks AWN-AP-54MR Manuel utilisateur

IP-COM

IP-COM AP355 Manuel utilisateur

Buffalo

Buffalo AirStation WLA-L11G Manuel utilisateur

EnGenius

EnGenius EnStationACv2 Manuel utilisateur

D-Link

D-Link DAP-3662 Manuel utilisateur

xG Technology

xG Technology xMax CN1300 Manuel utilisateur

Widelink

Widelink ezWave WAP-1100 Series Manuel utilisateur

Edimax

Edimax CAP1200 Manuel utilisateur

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuel utilisateur

Aruba

Aruba AP-203R Manuel utilisateur

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuel utilisateur

CreatComm

CreatComm TB5F Manuel utilisateur

SineDigital

SineDigital MW-1500AP(H) Manuel utilisateur

TP-Link

TP-Link AP9650 V1 Manuel utilisateur