TRENDnet TV-IP300 Mode d’emploi
Q: How can I configure my TV-IP300 (w) through the web-based configuration?
A:
Q: What is the default IP address of my TV-IP300 (w)?
A:
Q: How can I view the TV-IP300 (w) remotely if it’s behind a router or firewall?
A:
Open your web browser and type the IP address of the TV-IP300 in the address bar. The default IP
address is 192.168.0.30.
The default IP address is 192.168.0.30
Each camera behind a firewall or router will need one port forwarded for the video streaming. The
four default ports are:
1. 80 (TCP) HTTP Port
2. 8481 (TCP/UDP) Control Channel Port
3. 8482 (TCP/UDP) Audio Channel Port
4. 8483 (TCP/UDP) Video Channel Port
If you are installing multiple cameras you must change the port on the additional cameras.
Camera 1 is using the default ports. Camera 2 must use different ports. For example:
1. 81 (TCP) HTTP Port
2. 8491 (TCP/UDP) Control Channel Port
3. 8492 (TCP/UDP) Audio Channel Port
4. 8493 (TCP/UDP) Video Channel Port
You can change the ports on the camera on the System tab in the web-configuration page.
Step 1. Open your web browser and type the IP address of the TV-IP300 (w) in the address
bar. The default IP address is 192.168.0.30.
Step 2. Click on “System Administration”.
TV-IP300/TV-IP300W F.A.Q.
Step 3. Click on the “System" at the top of the page.
Q: How do I configure the camera to record motion?
A:Step 1. Open your web browser and type the IP address of the TV-IP300 (w) in the address bar.
The default IP address is 192.168.0.30.
Step 2. Click on “System Configuration”.
TV-IP300/TV-IP300W F.A.Q.
Step 3. Click on the “Motion Detection” link at the top of the page.
Step 4. Place a check mark in “Enable motion detection” and click “Save”.
Step 5. Click on “New” to define a motion detection area.
Step 6. Input a name in the “Window Name” field.
Step 7. Change the dimensions of the motion detection area to meet your requirements by
clicking and dragging the window.
Step 8. Adjust the Sensitivity and Percentage values to meet your requirements.
Step 9. Click “Save”.
Note: The Sensitivity rating determines the amount of motion in the created window to activate
motion. Setting it too high or too low may result in unexpected results.
Note: The Percentage rating determines the amount of space in the window that has to have
motion to activate motion detection.
Example: Sensitivity rating of 95% with a percentage of 2%. With these settings 2% of the
window must meet the 95% sensitivity rating to active motion detection.
TV-IP300/TV-IP300W F.A.Q.
Q: How do I upgrade the firmware of my camera?
A:Step 1. Start the IPView SP application by clicking on Start>All Programs> IPViewSP> I
PViewSP.
Step 2. Click on “System Administration”.
Step 3. Click “Tools”.
TV-IP300/TV-IP300W F.A.Q.
Step 5. Click “Update”.
Step 4. Click “Browse” and locate the firmware file and click open.
Q: Can my TV-IP300 (w) series camera use Power over Ethernet?
A:No, it does not support Power over Ethernet.
TV-IP300/TV-IP300W F.A.Q.
Step 1. Start the IPView Pro Program by going to Start>Programs>IPView Pro>IPView Pro.
Step 2. Click on the “System Configuration” button.
Q: How can I email snapshots based on motion from my camera?
A:
Step 3. Click on the System link at the top of the page. Fill in the SMTP section and click
“Save”.
Note: The second SMTP server is a back up. It does not send emails to both addresses
simultaneously. If the first one fails it will attempt to send the email out to the second account.
TV-IP300/TV-IP300W F.A.Q.
Step 4. Click on the “Application” link at the top of the page and place a check mark in “Send
snapshot image by email” next to the Motion detection section then click “Save”.
Q: How do I configure my TV-IP300 (w) series cameras to upload snapshots to an
FTP server?
A:Step 1. Open your web browser and type the IP address of the TV-IP300 (w) in the address
bar. The default IP address is 192.168.0.30.
Step 2. Click on “System Administration”.
TV-IP300/TV-IP300W F.A.Q.
Step 3. Click on “System” link at the top of the page. Fill in the FTP section and then click
“Save”.
Step 4. Click on the “Application” link at the top of the page. You can configure an FTP upload
on Motion Detection, on a Schedule or Manually. After you have configured the settings
click “Save”.
TV-IP300/TV-IP300W F.A.Q.
Q: How do I view the TV-IP300 (w) image using IPView Pro?
A:Step 1. Start the IPView SP Program by going to Start>Programs>IPView SP>IPView SP
Step 2. Click on “Camera 1".
Step 3. Enter the IP address, port and protocol. Also enter in the username and password if you
have assigned one to the camera. Click “Add”.
TV-IP300/TV-IP300W F.A.Q.
Note: You can also add the camera by clicking on browse. Highlight the camera and click on
“Add”.
Internet Explorer 5.0 and above.
Requirements
Memory Size:128M (256 Recommended)
Pentium III, 450 MHz or above
VGA card resolution: 800 x 600 or above
Q: Which web browsers will allow me to view the video from a TV-IP300 (w)?
A:
Q: How do I add user accounts to my TV-IP300 (w)?
A:Step 1. Open your web browser and type the IP address of the TV-IP300 (w) in the address
bar. The default IP address is 192.168.0.30.
Step 2. Click on “System Administration”.
TV-IP300/TV-IP300W F.A.Q.
Autres manuels pour TV-IP300
3
Ce manuel convient aux modèles suivants
1
Autres manuels TRENDnet Caméra de sécurité
TRENDnet
TRENDnet TV-IP410WN Manuel utilisateur
TRENDnet
TRENDnet TV-IP651WI Manuel utilisateur
TRENDnet
TRENDnet TV-IP121WN Manuel utilisateur
TRENDnet
TRENDnet TV-IP322WI Manuel utilisateur
TRENDnet
TRENDnet TV-IP300 Manuel utilisateur
TRENDnet
TRENDnet TV-IP341PI Manuel utilisateur
TRENDnet
TRENDnet TV-IP302PI Manuel utilisateur
TRENDnet
TRENDnet TV-IP862IC Manuel utilisateur
TRENDnet
TRENDnet EL-HS800 Manuel utilisateur
TRENDnet
TRENDnet TV-IP600W - Wireless Pan/Tilt/Zoom Internet Camera Server... Manuel utilisateur
TRENDnet
TRENDnet TV-IP342PI Manuel utilisateur
TRENDnet
TRENDnet TV-IP501P - ProView PoE Internet Camera... Manuel utilisateur
TRENDnet
TRENDnet TV-IP328PI Manuel utilisateur
TRENDnet
TRENDnet TV-IP121W Manuel utilisateur
TRENDnet
TRENDnet 15-AH28B Manuel utilisateur
TRENDnet
TRENDnet TV-IP300 Manuel utilisateur
TRENDnet
TRENDnet TV-IP212W - Wireless Internet Camera Server Manuel utilisateur
TRENDnet
TRENDnet TV-IP651W Manuel utilisateur
TRENDnet
TRENDnet TV-IP311PI Manuel utilisateur
TRENDnet
TRENDnet TV-IP312 Manuel utilisateur
