Travis Industries 36 CF II Manuel

36 CF II Fireplace

• Operation

• Maintenance

Tested and Listed by

OMNI-Test Laboratories, Inc.

Beaverton, Oregon

Report # 028- -57-5

AN I Z21.88b-2003

WARNING: If the information in these instructions is not followed e actly, a fire or

e plosion may result causing property damage, personal injury or loss of

life.

- Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this

or any other appliance.

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your building.

• Immediately call gas supplier from a neighbor's phone. Follow the gas supplier's

instructions.

• If you cannot reach your gas supplier, call the fire department.

- Installation and service must be performed by a qualified installer, service agency or

the gas supplier.

This appliance may be installed in an aftermarket permanently located, manufactured home (USA only)

or mobile home, where not prohibited by local codes.

This appliance is only for use with the type(s) of gas indicated on the rating plate. A conversion kit is

supplied with the appliance.

Owner's Manual

Mukilteo, WA 98275

2 Introduction

Travis Industries 4080204 100-01198_000

Introduction

We welcome you as a new owner of a 36 CF II gas fireplace. This manual details operation and

maintenance of this fireplace. Please familiarize yourself with the Owner's Manual before

operating your heater and save the manual for future reference.

Important Information

No other 36 CF II gas fireplace has the same serial

number as yours. The serial number is on the listing

label that is chained to the gas control valve. This

serial number may be needed in case you require

service.

Model: 36 CF II Fireplace

erial Number:

Purchase Date:

Purchased From:

traviswarranty.com

Or, mail your warranty card to:

Travis Industries House of Fire

4800 Harbour Pointe Blvd. W

Mukilteo, WA 98275

Save Your Bill of Sale.

To receive full warranty coverage, you will

need to show evidence of the date you

purchased your heater. Do not mail your

Bill of ale to us.

We suggest that you attach your Bill of

ale to this page so that you will have all

the information you need in one place

should the need for service or information

occur.

Installation Warnings

• Installation requirements are printed in the 36 CF II Installation Manual (part # 100-01197).

All requirements in the installation manual must be met.

• Failure to follow all of the requirements may result in property damage, bodily injury, or

even death.

• This heater must be installed by a qualified installer who has gone through a training

program for the installation of direct vent gas appliances.

• This appliance must be installed in accordance with all local codes, if any; if not, follow

ANSI Z223.1 and NFPA 54(88).

• In Manufactured or Mobile Homes must conform with Manufactured Home Construction

and Safety Standard, Title 24 CFR, Part 3280, or, when such a standard is not applicable,

the Standard for Manufactured Home Installations, ANSI/NCSBCS A225.1. This appliance

may be installed in Manufactured Housing only after the home is site located.

• The fireplace is designed to operate on natural gas, or propane (LP).

• All e haust gases must be vented outside the structure of the living-area. Combustion

air is drawn from outside the living-area structure.

• Notify your insurance company before hooking up this fireplace.

• The ceramic firebacks must be installed in this fireplace prior to operation.

Introduction 3

Table of Contents

Introduction and Important Information

Introduction.............................................................2

Important Information ...............................................2

Installation Warnings ................................................2

Features.................................................................3

Gas Input pecifications ........................................... 3

Safety Precautions

afety Precautions...................................................4

Operation

Before You Begin .....................................................6

Controls..................................................................6

tarting the Fireplace for the First Time....................... 8

Adjusting the Flame Height........................................8

Maintenance

Yearly ervice Procedure.......................................... 9

Glass Frame Removal and Installation........................ 10

Log et Installation .................................................. 11

Wiring Diagram........................................................ 17

Replacement Parts List ............................................ 17

Warranty

Warranty ................................................................ 18

Optional Equipment

Optional Equipment List............................................ 19

Inde

Index...................................................................... 20

Features

• Works During Power Outages

• tandard Remote Control with Thermostat

• Realistic "Wood Fire" Look

• Convenient Operating Controls

• Variable-Rate Heat Output

• Low Maintenance

Gas Input Specifications

Natural Gas Propane

Maximum BTU Input Per Hour 50,000 49,000

Minimum BTU Input on Low 28,500 26,900

4 Safety Precautions

IF YOU SMELL GAS:

* Do not light any appliance

* E tinguish any open flame

* Do not touch any electrical switch or plug or unplug anything

* Open windows and vacate building

* Call gas supplier from neighbor's house, if not reached, call fire department

This unit must be installed b

a qualified installer to prevent the possibilit

of an

explosion. Your dealer will know the requirements in your area and can inform you

of those people considered qualified. The room heater should be inspected and

cleaned before use and at least annually by a qualified service person. More

frequent cleaning may be required due to excessive lint from carpeting, bedding

material, etc.

The instructions in this manual must be strictl

adhered to. Do not use makeshift

methods or compromise in the installation. Improper installation will void the

warrant

and safet

listin

CH 4

- or -

83H

This heater is either approved

for natural gas (NG) or for

propane (LP). Burning the

incorrect fuel will void the

warranty and safety listing and

may cause an extreme safety

hazard. Direct questions

about the type of fuel used to

your dealer or installer

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

Contact

our local buildin

officials to obtain a permit and

information on any installation

restrictions or inspection

requirements in your area.

Notify your insurance

company of this heater as

well.

If the flame becomes soot

dark orange in color, or

extremely tall, do not operate

the heater. Call your dealer

and arrange for proper

servicing.

It is imperative that control

compartments, screens, or

circulating air passageways of

the heater be kept clean and

free of obstructions. These

areas provide the air necessary

for safe operation. ?Do not operate the heater if it is

not operating properly in any

fashion or if you are uncertain.

Call your dealer for a full

explanation of your heater and

what to expect.

Gas

Do not store or use

asoline or

other flammable liquids in the

vicinity of this heater.

AAAAA

Do not operate if an

portion of

the heater was submerged in

water or if an

corrosion occurs.

Immediately call a qualified

service technician to inspect

the appliance and to replace

any part of the control system

and any gas control that has

been under water.

Safety Precautions 5

Do not place clothin

or other

flammable items on or near

the heater. ecause this

heater can be controlled by a

thermostat there is a possibility

of the heater turning on and

igniting any items placed on

or near it.

ht the heater usin

the built-

in electronic igniter. Do not

use matches or any other

external device to light your

heater.

Allow the heater to cool before

carrying out any maintenance

or cleaning.

The viewin

lass should be

opened only for conducting

service. Do not operate with

cracked, broken, or removed

glass.

safet

screen or

uard

removed for servicing must be

replaced prior to operating the

heater.

Never remove, replace, modify

or substitute any part of the

heater unless instructions are

given in this manual. All other

work must be done by a trained

technician. Don't modify or

replace orifices.

Prior to removing the glass,

shut off gas to the appliance

(or remove the batteries from

the battery box and shut off

electricity to the fireplace).

This prevents any chance of

accidental burner ignition

when accessing the firebox.

This

Manual

Do not throw this manual awa

This manual has important

operating and maintenance

instructions that you will need

at a later time. Always follow

the instructions in this manual.

This unit is not for use with

solid fuel

Do not place an

thin

inside

the firebox (except the

included fiber logs).

If the fiber lo

s become

damaged, replace with Travis

Industries log set.

Instruct ever

one in the house

how to shut gas off to the

appliance and at the gas main

shutoff valve. The gas main

shutoff valve is usually next to

the gas meter or propane tank

and requires a wrench to shut

off.

Children and adults should be

alerted to the hazards of high

surface temperature and

should stay away to avoid

burns or clothing ignition.

Young children should be

supervised when they are in

the same room as the heater.

Travis Industries, Inc.

rants

no warranty, implied or stated,

for t e installation or

maintenance of your eater,

and assumes no

responsibility of any

consequential damage(s).

Operate the heater accordin

to the instructions included in

this manual.

If the main burners do not start

correctly turn the gas off to the

fireplace and call your dealer

for service.

6 Operation

Before You Begin

Read this entire manual before you use your new fireplace (especially the section " afety

Precautions" on pages 4 & 5). Failure to follow the instructions may result in property damage,

bodily injury, or even death.

Controls

Remote Control

The remote control can turn the fireplace on and off or operate as a thermostat. In addition, it can

turn the flame height up or down.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

Wall Switch

The wall switch can turn the fireplace on and off or turn the flame height up or down.

OFF

Operation 7

The Two Modes of Operation

This fireplace uses both a wall switch and thermostat to control the fireplace.

NOTE: Whichever

component is operated last

controls the fireplace. If

you are using the remote

and you press any button on

the wall switch, the remote

is no longer in control of the

fireplace until a button is

pressed on the remote.

OFF

NOTE: Whichever control is

operated last controls the

fireplace.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

Manual Mode

In manual mode you can turn the fireplace on and off using either the thermostat or remote.

imply press the “ON” and “OFF” buttons on either the wall switch or remote.

Thermostat Mode

While in thermostat mode, the remote will

monitor the temperature and turn the fireplace

on and off to meet the desired temperature.

To turn on Thermostat Mode:

Press the “MODE” button on the remote until

“ROOM” appears on the LCD display.

To turn off Thermostat Mode:

Press the “MODE” button on the remote until

“ROOM” no longer appears on the LCD

display.

ON H/L

OFF

Continuous Pilot

MODE

SET

TEMP

°F

ROOM

When the remote is in

thermostat mode the

word "ROOM" will

appear on the remote.

Adjusting the Target Temperature of the Thermostat:

Make sure the remote is in thermostat mode. Hold down the “ ET” button until the desired

temperature is displayed ( “ ET TEMP” will be displayed on the LCD, indicating that the

thermostat temperature is being set). The thermostat may be set at any temperature between 45°

and 99° F. If the desired temperature is missed, simply hold down the button (the temperature

will scroll up to 99° then re-start at 45°).

NOTE: If the fireplace is in thermostat mode, and any button on the wall switch is pressed, the

remote will return to manual mode. imply press any button on the remote to return control of

the fireplace to the remote.

WARNING: While in thermostat mode the fireplace will turn on and off to meet the temperature

demands of the remote. Do not place any items near the fireplace or conduct service without

removing the batteries and disabling the fireplace.

WARNING: If the remote is set to a high temperature the fireplace may remain on for an extended

period of time. This may be a concern to those using LP (propane).

8 Operation

Starting the Fireplace for the First Time

• Burn the heater at a high setting for an extended period (up to 48 hours). This ill cure the

painted surfaces. Fumes from the paint curing and oil burning off the steel ill occur. This is

normal. We recommend opening a indo to vent the room.

• Condensation may appear on the glass each time you start the fireplace - this is normal.

• Blue Flames ill occur on the fireplace hen it first comes on. After fifteen minutes the flames

ill turn a more realistic yello and orange color.

Adjusting the Flame Height

Adjustment with the Wall Switch (recommended)

With the fireplace in manual mode and the fireplace on, click the “HI” or “LO” button until the

desired flame height is achieved.

Adjustment with the emote

With the fireplace in manual mode and the fireplace on, click and hold the “ON” button until the

desired flame height is achieved. Each time the “ON” button is held do n, the flame height ill

toggle bet een getting taller (“HI” ill be displayed on the LCD screen) or getting smaller (“LO”

ill be displayed on the LCD screen).

Continuous Pilot – For Very Cold Conditions

This fireplace can be configured to run ith an intermittent or continuous (standing) pilot. For

normal conditions e recommend using the intermittent pilot (pilot is on only hen the main

burner is on). For extremely cold conditions e recommend using a continuous pilot (pilot is on all

the time). By having the pilot on continuously, a draft is established in the vent, allo ing the main

burner to turn on ith less air-flo disruption.

Setting the Fireplace to Continuous Pilot

Press and hold do n the “OFF Continuous Pilot” button on the remote for 10 seconds. “PILOT” ill

appear on the LCD screen, indicating that the fireplace is configured for a continuous pilot. To

configure the fireplace for an intermittent pilot, press and hold do n the “OFF Continuous Pilot”

button on the remote for 10 seconds until the “PILOT” is no longer visible on the LCD screen.

Child Protection Feature

The remote can be disabled to prevent children from operating the fireplace. This is done by

holding do n the “ON H/L” and “MODE” button for 5 seconds until “CP” (Child Protection) appears

on the screen. If any button is pressed on the remote “CP” ill appear on the screen indicating the

child protection feature is on. To turn this feature off, hold do n the “ON H/L” and “MODE” button

for 5 seconds until “CP” disappears from the screen.

Heat Bypass

This fireplace is equipped ith a heat bypass to adjust the amount of heat entering the room. The

bypass is located directly above the glass frame in the center of the fireplace.

Setting the Bypass to the Closed Position (more heat in the room)

Use a 1/4” nutdriver to turn the bypass clock ise.

Setting the Bypass to the Open Position (less heat in the room)

Use a 1/4” nutdriver to turn the bypass counter-clock ise.

Normal perating dors

This appliance has several areas that reach high temperatures. Dust or other particles on these

areas may burn and create an odor. This is normal during start-up. You may notice the smell is

more acute if the appliance as left idle for a long period.

Maintenance 9

Yearly Service Procedure

WARNING: Prior to removing the glass, shut off gas to the

appliance (or remove the batteries from the battery box and shut

off electricity to the fireplace). This prevents any chance of

accidental burner ignition when accessing the firebox.

• Failure to inspect and maintain the fireplace may lead to improper combustion and a potentially dangerous

situation. We recommend the following procedures be done by a qualified technician.

1. Remove the glass frame and log set (NOTE: the logs are very fragile - see page 11). If severely

deteriorated, replace. Check the logs for sooting. A small amount of soot along the bottom of the logs is

normal. If excessive sooting is found, the fireplace will require adjustment. Contact your dealer.

2. Inspect the burner and remove any debris.

• Make sure the burner is not warped, cracked, or damaged.

• Check the firebox and area around the pilot to make sure there is no warping or damage.

• If any problem is found, discontinue use and contact your dealer for service.

3. Replace the log set. Clean and replace the glasss. If the glass is damaged, replace. Make sure the

gasket along the perimeter of the glass contacts the face of the firebox and forms an air-tight seal. If it

does not, re-align or replace the gasket to insure an air-tight seal.

4. tart the burner. The flames should be orange/yellow and not touch the top of the firebox. If the pilot or

main burners do not burn correctly, contact your dealer for service.

5. Remove any debris or vegetation near the vent termination. Contact your dealer if any sooting or

deterioration is found near the vent termination.

10 Maintenance

Glass Frame Removal and Installation

WARNING: Prior to removing the glass, shut off gas to the

appliance (or remove the atteries from the attery ox and shut

off electricity to the fireplace). This prevents any chance of

accidental urner ignition when accessing the fire ox.

Warning: The appliance must e completely cool efore removing the glass.

Warning: Do not strike or slam the glass.

The glass frame is held in

place with four latches.

Use the door latch tool to pull the latch forward

and away from the glass frame.

These tabs insert over posts

on the fireplace and help

guide the glass into place.

REPLACING THE GLASS

Slide the glass into place and secure the four latches.

Lift and remove the glass frame

cover. Four hooks on the sides of

the coverhold it in place.

Autres manuels pour 36 CF II

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Travis Industries Cheminée intérieure

Travis Industries

Travis Industries Flush Wood Plus Manuel utilisateur

Travis Industries

Travis Industries Xtrordinair ProBuilder 36 CleanFace MV Manuel utilisateur

Travis Industries

Travis Industries 1080 CF Manuel utilisateur

Travis Industries

Travis Industries 864 See Through Manuel utilisateur

Travis Industries

Travis Industries 864 Clean Face GSR2 Manuel utilisateur

Travis Industries

Travis Industries 33 DVI Manuel utilisateur

Travis Industries

Travis Industries 21E Manuel utilisateur

Travis Industries

Travis Industries Xtrordinair 44 Elite Manuel utilisateur

Travis Industries

Travis Industries 564 Instructions d'installation

Travis Industries

Travis Industries Flush Plus Manuel utilisateur

Travis Industries

Travis Industries 21 TRV GreenSmart Manuel utilisateur

Travis Industries

Travis Industries Shadowbox Black Manuel utilisateur

Travis Industries

Travis Industries Interior Manuel utilisateur

Travis Industries

Travis Industries 4237 Manuel utilisateur

Travis Industries

Travis Industries GreenSmart Fireplace 564 SS Manuel utilisateur

Travis Industries

Travis Industries 864 HO NB GSR2 Manuel utilisateur

Travis Industries

Travis Industries DVS Ember-Fyre 2.1 Log Manuel utilisateur

Travis Industries

Travis Industries Small Flush Manuel utilisateur

Travis Industries

Travis Industries 564 HO GSR2 Manuel utilisateur

Travis Industries

Travis Industries 1750 Manuel utilisateur

Travis Industries

Travis Industries Fireplace Xtrordinair CoolSmart TV Manuel utilisateur

Travis Industries

Travis Industries 564 Manuel utilisateur

Travis Industries

Travis Industries 864 HO NB GSR2 Manuel utilisateur

Travis Industries

Travis Industries 4415 HO ST Manuel utilisateur

Manuels Cheminée intérieure populaires d'autres marques

Brigantia

Brigantia 35-DVRS31N-2 Manuel du propriétaire

Nordpeis

Nordpeis Bergen Manuel utilisateur

Superior

Superior BCT2536TMN Manuel utilisateur

Quadra-Fire

Quadra-Fire 5100I-GD-B Manuel utilisateur

Renaissance

Renaissance RUMFORD 1000 Manuel utilisateur

Lacunza

Lacunza IV-800 Manuel utilisateur

Baxi

Baxi 940 Instructions d'utilisation

Dru

Dru Maestro 60/2 Tall RCH Manuel utilisateur

Diamond Fireglass

Diamond Fireglass SS-O22 Manuel utilisateur

HearthStone

HearthStone Windsor Bay 8830 Manuel de programmation

Napoleon

Napoleon ASCENT B42 Manuel utilisateur

Enviro

Enviro E33GI Manuel utilisateur

Smeg

Smeg L30 FABE Instructions de montage

KEDDY

KEDDY K700 Manuel utilisateur

Godin

Godin 3451 Manuel utilisateur

Jøtul

Jøtul Jotul GI 535 DV IPI New Harbor Manuel utilisateur

Austro Flamm

Austro Flamm Heidi Back 2.0 945048 Manuel utilisateur

Desa

Desa CCFPDFT Manuel d'utilisation