Transition Networks SISGM1040-284-LRT Manuel utilisateur

SISGM1040-284-LRT Quick Start Guide

33807 Rev. B https://www.transition.com Page 1of 2

SISGM1040-284-LRT

Hardened Managed Switch, (8) 10/100/1000Base-T +

(4) 100/1000Base-X SFP Slots

Quick Start Guide

The SISGM1040-284-LRT provides eight 10M/100M/1G RJ45 ports,

four GbE SFP ports and one RJ45 console port. SISGM1040-284-LRT

provides high performance and environment flexibility for industrial applications.

Note: See the Install Guide for important Safety Warnings and Cautions, Features and Benefits, Ordering

Information, Specifications, Safety Instructions, Front Panel and LED Descriptions, Installation, Grounding, DIP

Switch Settings, Power Supply information, Connecting Power, CONSOLE Port, CLI Initialization, Troubleshooting,

Compliance, Warranty, and Rapid Ring operation.

Installation

Installation involves switch mounting, grounding, cable connection, configuration, and power connection

information. Caution: Read “Safety Warnings and Cautions” in the Install Guide before proceeding. Verify the box

contains one Managed Ethernet Switch, one DIN-Rail Clip, three DIN Clip Screws, one Console Cable, one Quick

Start Guide, one support postcard, and one Power Supply (optional; sold and packaged separately). Contact your

sales rep if you did not receive these items. Save the packaging for possible future use.

DIN Rail Mounting: 1. Screw the DIN-Rail bracket on with the bracket and screws in the accessory kit. 2. Hook the

unit over the DIN-Rail. 3. Push the bottom of the unit towards the DIN-Rail until it snaps into place.

Wall Mounting: 1. Screw on the wall-mount plate with the plate and screws in the accessory kit. See the Install

Guide for details.

Ethernet Interface (RJ45 Ethernet): The switch provides two types of electrical interfaces: RJ45 and optical (mini-

GBIC). To connect to a PC, use a straight-through or a cross-over Ethernet cable. To connect the SISGM1040-

184D-LRT to an Ethernet device, use UTP (Unshielded Twisted Pair) or STP (Shielded Twisted Pair) Ethernet

cables. See the Install Guide for pin assignments.

Ethernet Interface (Fiber, SFP): For a 100 Mbps fiber port available, prepare the LC connectors or SC connectors

(with the use of an optional SC-to-LC adapter). For the 1000 Mbps fiber ports, use mini-GBIC SFPs. These accept

plug in fiber transceivers that typically have an LC style connector. They are available with multimode, single

mode, long-haul or special-application transceivers. See the Install Guide for Warnings and Cautions.

Ground Screw: The front panel grounding screw can be used for grounding. Run the ground connection from the

ground screw to the grounding surface before connecting devices. ATTENTION: This case must be earth

grounded. No DC input may be earth grounded. Use Isolated Power Supply.

RESET button: Press to reboot the system without removing power.

DIP Switch: The front panel RM/CPL DIP switch lets you set Ring Settings. See “DIP Switch (Ring Settings)” in the

Install Guide. Note that you can also configure Ring settings via the Web UI and CLI.

LEDs: See the “LED Descriptions” in the Install Guide.

Console Port: is for local management by using a terminal emulator or a computer with terminal emulation

software. Settings: DB9 connector connect to PC COM port. Baud rate: 115200bps. 8 Data bits, 1 Stop bit.

Priority: None. Flow control: None. To connect the host PC to the console port, an RJ45 (male) connector-to-

RS232 DB9 (female) connector cable is required. The RJ45 connector of the cable is connected to the Console

port of the SISGM1040-384D-LRT. The DB9 connector of the cable is connected to the PC COM port.

SISGM1040-284-LRT Quick Start Guide

33807 Rev. B https://www.transition.com Page 2of 2

Power Supply: ATTENTION: This case must be earth grounded. No DC input may be earth grounded. Use Isolated

Power Supply. Power Connection Warning: Connect the power supply to the switch first, and then connect the

power supply to power; otherwise catastrophic product failure may occur. 1. Verify that power is off to the DC

circuit that you are going to attach to the switch PoE DC-input connector. This can be either of the two power

supplies (AC-input or DC-input) or site source DC. 2. As an added precaution, place an appropriate safety flag and

lockout device at the source power circuit breaker, or place a piece of adhesive tape over the circuit breaker

handle to prevent accidental power restoration while you are working on the circuit. Power Disconnection:

To disconnect power from the switch after a good boot: 1. Turn off power to the switch. 2. Disconnect the cables.

Various power supply models are available from Transition Networks (sold separately). Warning: You must use an

isolated power supply for Transition Networks to honor the switch warranty. Transition Networks provides Power

Supply 25165, Power Supply 25130, SPS-UA12DHT and PS-DC-DUAL Series. Each power supply model is described

in the Install Guide.

Connecting Power: The switch can be powered from two power supplies (input range 12V ~ 48V). Insert the

positive and negative wires into V+ and V- contacts on the terminal block and tighten the wireclamp screws to

prevent the wires from being loosened. Note: Make all cable connections before connecting Power.

Power Connector (4-Pin Terminal Block): Input: DC 12-48V. P1 +/- Power Input 1 plus and minus. P2 +/- Power

Input 2 plus and minus. ALM Alarm Relay Output.

Connecting the DI/DO (Digital Input / Digital Output) Relay: 1. Insert the negative (ground)/positive DI/DO Relay

wires into the + and - terminals, respectively. 2. Use a small flat-blade screwdriver to tighten the wire-clamp

screws on the front of the Terminal Block connector. 3. Insert the Terminal Block connector prongs into the

Terminal Block receptor. See the DI/DO Use Case in the Install Guide.

Connect and Log In via CONSOLE Port: You can log on to the switch with the user

name and password. The default CLI user name and password is admin.

You should change the password as soon as possible.

1. Connect a PC to the SISGM1040-284-LRT Ethernet port (RJ45 Ethernet port).

2. In Telnet, enter the command telnet 192.168.1.77.

3. Login with default Username (admin)and Password (admin).

4. Change the IP with the CLI commands in the CLI Reference.

Connect and Log In via Web Browser: After initial power up, perform the initial

switch configuration using a web browser. To begin the initial configuration

stage, reconfigure your PC’s IP address and subnet mask so the PC can

communicate with the switch. After changing PC’s IP address, you can access the

switch’s Web GUI using the switch’s default IP address of 192.168.1.77. The

default Subnet Mask is 255.255.255.0. The default Username and Password are

admin. You should change the password as soon as possible. See Web User

Guide for configuring other switch features.

For Transition Networks Drivers, Firmware, etc. go to the Product Support webpage (logon required).

For Manuals, Data Sheets, etc. go to the Support Library (no logon required).

Address comments on this product or manual to Transition Networks Inc. | 10900 Red Circle Drive, Minnetonka,

MN 55343 | tel: +1.952.941.7600 | toll free: 1.800.526.9267 | fax: 952.941.2322 | sales@transition.com

| techsupport@transition.com | customerservi[email protected]om | web: https://www.transition.com

Autres manuels pour SISGM1040-284-LRT

Table des matières

Autres manuels Transition Networks Changer

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-384-LRT-C Manuel utilisateur

Transition Networks

Transition Networks SM TAT4X Series Manuel utilisateur

Transition Networks

Transition Networks SM12DP2XA Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks STACKMASTER TX12 Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-3 L Series Manuel utilisateur

Transition Networks

Transition Networks SM8T2DPA Manuel utilisateur

Transition Networks

Transition Networks SISTP10xx-141-LR(T) Manuel utilisateur

Transition Networks

Transition Networks SISTP1040-382B-LRT Manuel utilisateur

Transition Networks

Transition Networks SISTG1040-242-LRT Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-0403 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-1600 Manuel utilisateur

Transition Networks

Transition Networks SISTM1040-262D-LRT Manuel utilisateur

Transition Networks

Transition Networks SESPM1040-541-LT Series Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-3 L Series Manuel utilisateur

Transition Networks

Transition Networks StackMaster SMHB-E-FL-12 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-1002 Manuel utilisateur

Transition Networks

Transition Networks SISTM1040-262D-LRT-B Instructions d'utilisation et d'entretien

Transition Networks

Transition Networks SISTF10xx-130-LR(T) Manuel utilisateur

Transition Networks

Transition Networks SM24-100SFP-AH Manuel utilisateur

Transition Networks

Transition Networks SM16TAT2SA Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur