Transition Networks E-TBT-HB-0400 Manuel utilisateur

For assistance in installing, using, or

maintaining the TRANSITION Networks

Model 0400 Ethernet Pocket Hub,

contact TRANSITION Networks

Technical Support at:

(800) 260-1312

or contact your local distributor.

7333.D

™™

Pocket HubEthernet

(E-TBT-HB-0400)

Model 0400

MODEL 0400 ETHERNET POCKET HUB

SPECIFICATIONS

Standards

IEEE 802.2, 802.3

Physical

Dimensions

4.80" X 2.77" X 0.95" (122mm x 70mm x 24mm)

Power Supply Adapter

AC Input:

PN Requirement Location

3518 120 volts, 60 hertz, 28 watts USA/Canada/Mexico

3516 230 volts, 50 hertz, 28 watts Europe

3514 100 volts, 50-60 hertz, 28 watts Japan

3517 240 volts, 50 hertz, 28 watts United Kingdom

3515 240 volts, 50 hertz, 28 watts Australia

DC Output:

12 volts at 500 mA maximum.

MTBF 47,000 hours

Environment

Temperature: 0-50°C (32° to 122° F )

Humidity 10-90%, non condensing

Altitude 0-10,000 feet

Warranty

5 years

Model 0400

Model 0400 Ethernet™ Pocket Hub™ 16

CAUTION: RJ connectors are NOT INTENDED FOR

CONNECTION TO THE PUBLIC TELEPHONE

NETWORK. Failure to observe this caution could result

in damage to the public telephone network.

Compliance Information

UL Listed

C-UL Listed (Canada)

CISPR/EN55022 Class A

FCC Regulations

This equipment has been tested and found to comply with the limits for a class

A digital device, pursuant to part 15 of the FCC rules. These limits are

designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment

generates, uses, and can radiate radio frequency energy and, if not installed

and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a

residential area is likely to cause harmful interference, in which case the user

will be required to correct the interference at the user’s own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for

digital apparatus set out on the radio interference regulations of the Canadian

Department of Communications.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause

radio interference in which case the user may be required to take adequate

measures.

form or by any means – graphic, electronic, or mechanical – without written

permission from TRANSITION Networks Inc.

Trademark Notice

All registered trademarks and trademarks are the property of their respective

owners.

Der Anschluss dieses Gerätes an ein öffentlickes

Telekommunikationsnetz in den EG-Mitgliedstaaten verstösst gegen die

jeweligen einzelstaatlichen Gesetze zur Anwendung der Richtlinie

91/263/EWG zur Angleichung der Rechtsvorschriften der

Mitgliedstaaten über Telekommunikationsendeinrichtungen

einschliesslich der gegenseitigen Anerkennung ihrer Konformität.

10Base2 Cable Specifications

The physical characteristics of the 10Base2 cable must meet or exceed IEEE 802.3

10Base2 specifications.

Cable Characteristics:

Cable type: Stranded Coaxial RG58 (ThinNet)

Impedance: 50 Ω@ 10 MHz

Mutual Capacitance: 24 pF/ft ±20% @ 10 MHz

Maximum Cable Length:185 meters (610 feet)

Maximum number network connections:30

Minimum distance between connections: 0.5 meters (1.6 feet)

Terminate 10Base2 cable at one end using a 50 ohm terminator and at the

other end using a 50 ohm terminator grounded to earth ground.

10BaseT Cable and Connector Specifications

The physical characteristics of the 10BaseT cable must meet or exceed IEEE 802.3

10BaseT specifications.

10BaseT Cable Characteristics:

Category 3 wire or better is required; category 5 wire is recommended. Either

shielded twisted pair (STP) or unshielded twisted pair (UTP) can be used. DO

NOT USE FLAT OR SILVER SATIN WIRE.

Category 3:

Gauge 24 to 22 AWG

Attenuation 28 dB/1000’ @ 10 MHz

Differential Characteristic Impedance 100 Ω±10% @ 10 MHz

Category 5:

Gauge 24 to 22 AWG

Attenuation 20 dB/1000’ @ 10 MHz

Differential Characteristic Impedance 100 Ω±10% @ 10 MHz

Maximum Cable Length: 100 meters (330 feet)

10BaseT Connector Characteristics:

The two active pairs in a 10BaseT network are pins 1 & 2 and pins 3 & 6. Use

only dedicated wire pairs (such as blue/white & white/blue, orange/white &

white/orange) for the active pins. 10BaseT cable for unlike devices (such as

hub to terminal device) must be configured as straight through; 10BaseT cable

for like devices (such as hub to hub or terminal device to terminal device) must

be configured as crossover.

Twisted

Pair #1

Twisted

Pair #2

Straight Through Cable

Table of Contents

1 INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . 1

The 0400 Ethernet Pocket Hub . . . . . . . . . . . . . . . . . . . . . . .1

0400 Pocket Hub Features . . . . . . . . . . . . . . . . . . . . . . . . . . . .1

Networking the 0400 Pocket Hub . . . . . . . . . . . . . . . . . . . . . . .2

0400 Ethernet Pocket Hub Connectors and Status LEDs . . . . .3

2 SITE CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . 4

Ensuring Correct Segment Number . . . . . . . . . . . . . . . . . . . .5

Ensuring Correct 10BaseT Configuration . . . . . . . . . . . . . . . .6

3 INSTALLATION. . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Unpacking 0400 Pocket Hub . . . . . . . . . . . . . . . . . . . . . . . .7

Connecting 10Base5 Cable . . . . . . . . . . . . . . . . . . . . . . . . . .8

Connecting 10BaseT Cable . . . . . . . . . . . . . . . . . . . . . . . . . .8

Connecting Power to 0400 Pocket Hub . . . . . . . . . . . . . . . .10

4 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11

Monitoring Power LED . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Monitoring Link/Transmit LEDs . . . . . . . . . . . . . . . . . . . . . .11

5 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . 12

Fault Isolation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

Technical Support Contact . . . . . . . . . . . . . . . . . . . . . . . . .12

WARRANTY STATEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

CABLE SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

0400 ETHERNET POCKET HUB SPECIFICATIONS . . . . . . 17

Model 0400 i

15 Ethernet™ Pocket Hub™

ETHERNET CABLE SPECIFICATIONS

AUI Cable and Connector Specifications

The cable is a special 4-pair individually shielded with an overall braided

shield.

Maximum AUI Cable Length: 50 meters (165 feet)

AUI Connector Characteristics:

AUI Port: Male DB-15 with locking posts.

AUI Connection: Cable shell must be grounded.

Connector Legend: 1 Logic Ref. 6 Power Return 11 Logic Ref

2 Collision+ 7 N/C 12 Receive

3 Transmit+ 8 Logic Ref. 13 Power

4 Logic Ref. 9 Collision-- 14 Logic Ref.

5 Receive+ 10Transmit- 15 N/C

10BaseFL Cable and Connector Specifications

The physical characteristics of the 10BaseFL cable must meet or exceed IEEE

802.3 10BaseFL specifications.

10BaseFL Cable Characteristics:

Fiber Optic Cable Recommended: 62.5/125 µm multimode fiber

Optional: 100/140 µm multimode fiber

85/125 µm multimode fiber

50/125 µm multimode fiber

Fiber Optic Transmitter Power: Average power: -15.0 dBm

Peak power:-12.0 dBm ±1dBm

Fiber Optic Receiver Sensitivity: Average sensitivity: -27.4 dBm

Bit error rate: ≤10-10

Maximum Cable Length: 2000 meters (6500 feet)

10BaseFL Connector Characteristics:

ST type connectors (SMA type available upon request)

10Base5 Cable and Connector Specifications

The physical characteristics of the 10Base5 cable must meet or exceed IEEE 802.3

10Base5 specifications.

10Base5 Cable Characteristics:

Cable type: RG8 Solid Coaxial (ThickNet)

Impedance: 50 Ω@ 10 MHz

Capacitance: 26pF/ft

Maximum Cable Length: 500 meters (1650 feet)

Maximum number network connections: 100

Minimum distance between connections: 2.5 meters (8.2 feet)

Terminate 10Base5 cable at one end using a 50 ohm terminator and at the

other end using a 50 ohm terminator grounded to earth ground.

Maximum number of terminal devices on Ethernet network: 1024

Model 0400 14

1Ethernet™ Pocket Hub™

1. INTRODUCTION

This guide is intended for the system or network administrator

responsible for installing and monitoring a TRANSITION Networks

0400 Ethernet Pocket Hub. A working knowledge of local area

network (LAN) operations, including familiarity with communications

protocols used on interconnected LANs, is assumed.

The 0400 Ethernet Pocket Hub

The Model 0400 10BaseT 4-Port Ethernet Hub (E-TBT-HB-0400), is a

low cost Ethernet repeater. Designed to meet IEEE 802.3 10BaseT

standards, the 0400 Pocket Hub is a fully functional repeater in a

compact (4.80" X 2.77" X 0.95”) case.

0400 Ethernet Pocket Hub Features

• automatic link partitioning (jabber function isolates network

failures)

• preamble regeneration

• automatic polarity detection and correction

Ethernet™

Pocket Hub™

Power

E-TBT-0400A

networks

TRANSITION

Mpls, MN 55344

4 3 2 1

The sole purpose of this remedy shall be provided the customer with the replacement or

repair of non-conforming goods in the manner described in this Warranty statement. This

exclusive remedy shall not be deemed to have failed of its essential purpose so long as TN is

willing and able to repair or replace the defective item(s) or refund the purchase price.

TN reserves the right to inspect products claimed to be defective under warranty either at the

customer’s location or at TN’s plant. TN assumes no liability for liability charges incidental

to the adjustment, service, repairing, removal or replacement of the product, or other costs,

or the expense of repairs made outside of its factory, except when made with TN’s prior

written consent. Additionally, Transition Networks reserves the right to charge for all testing

and shipping incurred, if after testing, a return is classified as “No Problem Found”.

TN’s total liability in connection with the products and their installation to all persons and

from all causes in the aggregate, whether in contract, tort, or strict liability, shall not exceed

the amount paid to TN for the product directly related to the alleged damage. However, in

no event shall TN have any liability to a customer or any third party for products

manufactures according to the customer’s specifications.

C. Return Procedure

The customer must follow this procedure for the return of defective items:

1. Locate the serial number(s) of the item(s) to be returned.

2. Determine the date the item(s) was received.

3. Contact Transition Networks Technical Support to determine if the problem can be

corrected on site.

If not, and the product is covered by warranty, then:

• Call the distributor directly or contact TN.

• Request a Return Material Authorization (RMA).

• Ship the item, prepaid in original packaging to Transition Networks at the above

address.

• Include the RMA number on the outside of the carton and/or on the Packing List.

• Include a copy of the RMA form.

• Include a copy of the original invoice or packing list (if possible) to expedite

processing.

• The item(s) may be shipped by the customer or the distributor.

• Transition Networks will repair or replace the unit, at TN’s discretion, and cover the

cost of the return freight to the distributor or to the customer, whichever requested

the RMA number.

If the item(s) was received more than five years ago, or if the item(s) is no longer covered by

warranty for other reasons, then:

• Call the distributor or contact TN.

• Request a Material Repair Authorization number (MRA).

• Ship the item(s), prepaid, in the original packaging to Transition Networks at the

above address.

• Include the MRA number on the outside of the carton add/or on the Packing List.

• Include a copy of the MRA form.

• Include a copy of the original invoice or packing list (if possible) to expedite processing.

• Only the customer (end-user) may send the items(s) to TN.

• TN will contact the customer after the item(s) have been received, inspected, and a

cost estimate of the repair determined.

• The repair charges may be billed, with customer’s approval, though the distributor, or

on a prepaid or C.O.D. basis directly to the customer. The charges will include the

cost of shipping.

The return authorization numbers are valid only for 90 days from the date issued.

Model 0400 2

13 Ethernet™ Pocket Hub™

Networking the 0400 Ethernet Pocket Hub

The 0400 Pocket Hub can function in both simple and complex

networks.

When connected to a 10Base5 backbone, the 0400 Pocket Hub

alone provides a simple, local network solution.

When linked to other Pocket Hubs and connected to a 10Base5

backbone, the 0400 Pocket Hubs function in complex Ethernet

networks.

Ethernet™

Pocket Hub™

Ethernet™

Pocket Hub™

TR ANSITIO N

networks

Mpls,MN55344

TR ANSITIO N

networks

Mpls,MN55344

Ethernet™

Pocket Hub™

Ethernet™

Pocket Hub™

TR ANSITIO N

networks

Mpls,MN55344

TR ANSITIO N

networks

Mpls,MN55344

Ethernet™

Pocket Hub™

networks

TRANSITION

Mpls,MN 55344

Warranty Statement

A. Five Year Warranty

Transition Networks, Inc. (TN) warrants, for a period of five years, that TN products (with

the exception of power supplies and fans that TN warrants for two years) will be free from

defects in materials and workmanship, and will be in conformity with TN’s specifications.

TN’s warranty on products manufactured by or assembled for TN in accordance with a

customer’s specifications, is a five-year warranty that the goods conform to such

specifications.

The warranty is invalidated if the goods have been subject to alterations, misuse, accident,

Acts of God (e.g., damage by floods, lightning strikes, Etc.), tampering, improper

maintenance, improper installation, or abuse. If the user is unsure about the proper means

of installing or using the equipment, contact TN’s free Technical Support or Network

Design Services, which can be reached by:

Telephone 1.800.LAN.WANS or 612.941.7600

Fax 612.941.2322

E-mail [email protected]

Internet http://www.transition.com

THE ABOVE WARRANTY IS EXCLUSIVE AND EXTENDS ONLY TO PRODUCTS

ASSEMBLED BY TRANSITION NETWORKS, INC. TO THE EXTENT PERMITTED BY LAW,

TN DOES NOT MAKE AND DISCLAIMS ALL OTHER WARRANTIES, EXCEPT TITLE,

EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY WARRANTY OF

DESCRIPTION, MERCHANTIBILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-

INFRINGEMENT, AND ANY WARRANTY BASED UPON PRIOR WRITTEN OR ORAL

REPRESENTATIONS REGARDING SUCH PRODUCTS MADE BY TN, ITS EMPLOYEES,

AGENTS, OR REPRESENTATIVES.

B. Limitations and Exclusions

If the customer believes any goods sold by TN are defective and within the warranty period,

the following general procedure will be followed:

1. Locate the serial number and delivery date of the item(s).

2. Notify TN within the warranty period.

3. TN will promptly issue a return authorization form for the goods.

4. Upon receiving the form, the customer will promptly return the item(s) at customers

own expense, shipped prepaid, to the distributor from which it was purchased, or

directly to TN.

TN will only accept goods for return if the following conditions have been met:

1. A return form is obtained from TN.

2. The freight charges have been prepaid by the customer.

3. Goods are re-packed in their original packaging.

If under warranty TN shall, at its option, (1) repair the goods free of charge (2) replace the

goods free of charge, or (3) accept the return of the item(s) and credit the current price to

the reseller (within 90 days of purchase), or (4) if the goods are not under warranty, will

repair the item(s) at a minimum charge of USD $200 (two hundred U.S. dollars) per item.

THIS IS THE EXCLUSIVE REMEDY FOR ANY BREACH OF WARRANTY. IN NO EVENT

SHALL TRANSITION NETWORKS BE LIABLE FOR SPECIAL, INDIRECT, INCIDENTAL OR

CONSEQUENTIAL DAMAGES OF ANY KIND, WHETHER FOR BREACH OF ANY

CONDITION OF SALE, FOR NEGLIGENCE, ON THE BASIS OF STRICT LIABILITY,

CONTRACT, OR OTHERWISE AND IRRESPECTIVE OF WHETHER TN IS INFORMED BY

CUSTOMER OF THE POSSIBILITY OF SUCH DAMAGES IN ADVANCE OF THIS SALE.

Model 0400 12

3Ethernet™ Pocket Hub™

5. MAINTENANCE

WARNING: DO NOT, UNDER ANY CIRCUMSTANCES,

open and attempt to repair the 0400 Pocket Hub or power

supply adapter unit. Failure to observe this warning could

result in personal injury or death from electrical shock.

NOTE: Failure to observe the above warning will immediately void

the warranty.

Fault Isolation

If two network devices fail to communicate through the 0400

Pocket Hub, consider the following:

• Are the LEDs described in the previous section functioning

properly?

• Do network devices have Link Integrity enabled?

• Do network devices communicate when the 0400 Pocket

Hub is not installed between them?

• Is flat or “silver satin” wire used in site internal wiring?

• Are internal wiring patch cords, punch down blocks, and

wall jacks properly pinned or configured?

• Is the AUI cable unbroken and properly connected?

• Are network interface cards properly configured?

Technical Support Contact

For assistance in fault isolation and in maintaining the 0400 Pocket

Hub, contact:

Technical Support (800) 260-1312

or your local distributor.

0400 Ethernet Pocket Hub Connectors and

Status LEDs

RJ-45 Connectors

Four (4) 10BaseT RJ-45 jack

connectors are located at

one end of the 0400 Pocket

Hub. The RJ-45 jacks

support connection to

shielded or unshielded 100

ohm twisted pair 10BaseT

cable.

AUI and Power Supply Adapter Connectors

An external power supply

adapter connector and an

AUI connector are located at

the other end of the 0400

Pocket Hub. The power

supply adapter connector

supplies external power. The

AUI connector supports

connection to 10Base5

through an AUI drop cable.

Status LEDs

Power and Link/Transmit

status LEDs are located at the

side of the 0400 Pocket Hub.

The Power LED indicates

connection to power. The

Link/ Transmit LEDs track

the four 0400 Pocket Hub

connections to 10BaseT.

RJ-45 Connectors

Female AUI Connector

Power Supply Adapter

Connector

Status LEDs

Model 0400 4

11 Ethernet™ Pocket Hub™

4. OPERATION

The 0400 Pocket Hub normally requires no intervention beyond

occasionally monitoring the Power and Link/Transmit LEDs.

Monitoring Power LED

The green Power LED is illuminated when the Pocket Hub is

connected to power.

Monitoring Link/Transmit LEDs

Each of the green Link/Transmit LEDs , associated with one of the

eight RJ-45 ports:

•is illuminated when a device is connected to the RJ-45

port

•flashes slowly as data is transmitted

•flashes quickly if the associated RJ-45 port has been

automatically partitioned.

Power LED

Link/Transmit LEDs

2. SITE CONSIDERATIONS

The site for the 0400 Ethernet Repeater Hub must provide:

•AC power outlet for each Hub

•Adequate ventilation

•Standard environmental conditions

•Isolation from electrical noise, including radio transmitters

and broadband amplifiers, motors, high power electrical

lines, or fluorescent light fixtures.

Additionally:

•The twisted pair cables should not run in the same conduit

with power line cables.

•Phone lines should be separated from data cables.

•Flat or “silver satin”wires should not be used.

And:

•Since the 0400 Ethernet Pocket Hub functions as an

Ethernet Repeater, the entire 0400 Ethernet Repeater Hub

installation should comply with the IEEE Ethernet 802.3

specification, including segment number.

•RJ-45 connected cables should be configured as crossover

or straight through according to installation requirements.

Model 0400 10

5Ethernet™ Pocket Hub™

Connecting Pocket Hub to Terminal Devices

Use a straight through cable to connect Pocket Hub to terminal

devices.

Connecting Power to 0400 Pocket Hub

To power ON the 0400 Pocket Hub:

1. Locate the power receptacle on the back of the 0400

Pocket Hub.

2. Connect the 0400 Pocket Hub power connector end of

the power supply adapter to the Pocket Hub.

3. Connect the external power connector end of the power

supply adapter to external AC power.

NOTE: After the power supply adapter is connected to the 0400

Pocket Hub and to external power, the green Power LED is

illuminated.

Ensuring Correct Segment Number

Ethernet 802.3 specifications define segment number, as well as cable

characteristics. (A segment is the cable connection between cable

interfaces in an Ethernet LAN. Up to one-hundred 10Base5

connections can be made in one segment.)

When connecting Pocket Hubs, the transmission path between any

two Data Terminating Equipment (DTE) terminals can consist of no

more than five segments.

To assign segment numbers to cable connections:

1. Determine the two terminals in the network which are

separated by the greatest number of segments.

2. Assign a segment path between the terminals by labeling the

cable connected to one of the terminals “segment 1”and the

segment connected to the other terminal “segment n”(n =

total number of segments ≤5).

3. To verify that no segment paths contain more than n

segments, assign segment paths and numbers to all other

terminals.

Ethernet™

Pocket Hub™

Ethernet™

Pocket Hub™

TR ANSITIO N

networks

Mpls,MN55344

TR ANSITIO N

networks

Mpls,MN55344

Ethernet™

Pocket Hub™

Ethernet™

Pocket Hub™

TR ANSITIO N

networks

Mpls,MN55344

TR ANSITIO N

networks

Mpls,MN55344

Ethernet™

Pocket Hub™

networks

TRANSITION

Mpls,MN 55344

Straight-through 10BaseT

Model 0400 6

9Ethernet™ Pocket Hub™

Connecting10BaseT Cable (continued)

Connecting to External Hub through Wall Outlet

Use a crossover cable to connect Pocket Hub to the wall plate.

Use a straight through cable to connect Pocket Hub to terminal

devices.

Connecting two Pocket Hubs

Use a crossover cable to connect Pocket Hubs.

Use a straight through cable to connect Pocket Hub to terminal

devices.

Ethernet™

Pocket Hub™

networks

TRANSITION

Mpls,MN 55344

Ethernet™

Pocket Hub™

networks

TRANSITION

Mpls,MN 55344

Straight-through 10BaseT

Crossover 10BaseT

wall plate

Ethernet™

Pocket Hub™

networks

TRANSITION

Mpls,MN 55344

Straight-through 10BaseT

Crossover 10BaseT

Ensuring Correct 10BaseT Configuration

The 10BaseT cable and RJ-45 jacks for Hub to Terminal connections

must be configured as straight through. The 10BaseT cable and RJ-45

jacks for Hub to Hub connections must be configured as crossover.

18RJ-45PLUG

RJ-45JACK

234567

The two active pairs in a

10BaseT network are pins

1 & 2 and pins 3 & 6. Use

only dedicated wire pairs

(such as blue/white &

white/blue, orange/white

& white/orange) for the

active pins.

Crossover Cable

at RJ-45 Plug

Hub . . . . . . . . . . . . . . .Hub

RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male

1 . . . . . . . . . . . . . . . . . . .3

2 . . . . . . . . . . . . . . . . . . .6

3 . . . . . . . . . . . . . . . . . .1

6 . . . . . . . . . . . . . . . . . .2

Straight Through Cable

at RJ-45 Plug

Hub . . . . . . . . . . . . . . . .PC, transceiver, NIC, printer

RJ-45 Male . . . . . . . . . . . . . . .RJ-45 Male

1 . . . . . . . . . . . . . . . . . . .1

2 . . . . . . . . . . . . . . . . . .2

3 . . . . . . . . . . . . . . . . . .3

6 . . . . . . . . . . . . . . . . . . .6

Model 0400 8

7Ethernet™Pocket Hub™

3. INSTALLATION

NOTE: 0400 Ethernet Pocket Hub Link Integrity cannot be

disabled. All devices connected to the Pocket Hub MUST

have link functions enabled.

To install the 0400 Ethernet Pocket Hub:

•Unpack the 0400 Pocket Hub.

•Connect 10Base5 Cable to the 0400 Pocket Hub.

•Connect 10BaseT Cable to the 0400 Pocket Hub.

•Connect the 0400 Pocket Hub to power.

Direction is provided in the pages that follow.

Unpacking the 0400 Pocket Hub

The 0400 Ethernet Pocket Hub packing contents should include the

following:

Item Part Number

0400 Pocket Hub E-TBT-HB-0400

Power Supply Adapter 3518, 3517, 3516, 3515, or 3514,

(depending upon power configuration

in country where installed)

User’s Guide 7333

Connecting10Base5 Cable

NOTE: Up to one-hundred 10Base5 connections can be made in one

segment.

To connect 10Base5 Cable to Pocket Hub female AUI connector:

1. Locate or build IEEE 802.3 compliant AUI drop cable.

2. Connect AUI drop cable male DB-15 connector to the

Pocket Hub AUI connector.

3. Connect AUI drop cable female DB-15 connector to the AUI

port on a transceiver or media attachment unit (MAU).

Connecting10BaseT Cable

To connect 10BaseT Cable to Pocket Hub RJ-45 connectors:

1. Locate or build 10BaseT cables with the following

characteristics:

•802.3 compliant (See page 14)

•correct (straight through or crossover) cable configuration

for site installation (See page 6)

•male RJ-45 plug connectors installed at both cable ends.

2. Connect male RJ-45 plug connector at one end of 10BaseT

cable to Pocket Hub RJ-45 jack connector.

3. Connect male RJ-45 plug connector at other end of 10BaseT

cable to DTE terminal RJ-45 jack connector (using straight

through cable orientation) or to Pocket Hub RJ-45 jack

connector (using crossover cable orientation). NOTE:

Examples are provided in the pages that follow.

Ethernet™

Pocket Hub™

networks

TR ANSITIO N

Mpls,MN55344

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Transition Networks Changer

Transition Networks

Transition Networks MIL-S800I-V2 Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-3-L Series Manuel utilisateur

Transition Networks

Transition Networks ETHERNET POCKET HUB 401 Manuel utilisateur

Transition Networks

Transition Networks PSV-2/14-45 Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA Manuel utilisateur

Transition Networks

Transition Networks SISGM-CHAS L2 Manuel utilisateur

Transition Networks

Transition Networks SM4T4DPA Manuel utilisateur

Transition Networks

Transition Networks SM Series Manuel utilisateur

Transition Networks

Transition Networks E-TBT-HB-0802 Manuel utilisateur

Transition Networks

Transition Networks SISTG1040-242-LRT Manuel utilisateur

Transition Networks

Transition Networks SM12DP2XA Manuel utilisateur

Transition Networks

Transition Networks MIL-S2400S Manuel utilisateur

Transition Networks

Transition Networks SM24TBT2DPA Manuel utilisateur

Transition Networks

Transition Networks mil-sm8dpa Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks SISTG1040-242-LRT Manuel utilisateur

Transition Networks

Transition Networks SM24TAT4GPA Manuel utilisateur

Transition Networks

Transition Networks SM12DP2XA-NA Manuel utilisateur

Transition Networks

Transition Networks SM8TAT2SA Mode d’emploi

Transition Networks

Transition Networks SM8T2DPA Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-582-LRT Manuel utilisateur

Transition Networks

Transition Networks SISGM1040-184D-LRT Manuel utilisateur

Transition Networks

Transition Networks SM24DPB Manuel utilisateur

Transition Networks

Transition Networks SISPM1040-384-LRT-C Manuel utilisateur

Manuels Changer populaires d'autres marques

URC

URC Total Control MFS-8 Manuel utilisateur

Azbil

Azbil HPQ-D11 Manuel utilisateur

Sony

Sony DFS-900M Manuel utilisateur

SICK

SICK i17S Manuel utilisateur

F&F

F&F SZR-277 Manuel utilisateur

Shure

Shure UAMS/BK Manuel utilisateur

Dräger

Dräger X-zone Switch Off Manuel utilisateur

Asco

Asco Joucomatic 349 Series Manuel utilisateur

BT Mini Hub Manuel utilisateur

D-Link

D-Link DES-1226G Manuel utilisateur

Johnson Controls

Johnson Controls FS80-C Manuel utilisateur

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuel utilisateur

MicroNet

MicroNet SP1200A Manuel utilisateur

Ruijie

Ruijie RG-PF2920 Series Manuel d'installation et d'exploitation

Altinex

Altinex DA1914SX Manuel utilisateur

MiLAN

MiLAN MIL-SM2401M Manuel utilisateur

RJM

RJM MASTERMIND PBC/6X Manuel utilisateur

Atlas

Atlas MMK-KVM8 Manuel utilisateur