Transition Networks SPSVT26xx-10x Manuel utilisateur

User’s Guide

SPSVT26xx-10x

Stand Alone Device

•High-Speed Serial

• V.35/X.21/RS449/RS530/RS232

• Copper to Fiber

Transition Networks SPSVT26xx-10x

series high-speed serial copper-to-fiber

Device connect V.35, X.21, RS-449, RS-

530, or RS-232 signals on copper cable, at

speeds up to 10 Mb/s, through a universal 26-pin serial interface connector to fiber-optic

cable. Transition Networks also supplies cables for connecting network equipment to the

SPSVT26xx-10x series Device.

Cable Options . . . . . . . . . . . . . . . . . .3

Installation . . . . . . . . . . . . . . . . . . . . .4

Operation . . . . . . . . . . . . . . . . . . . . .9

Cable Specifications . . . . . . . . . . . . .10

Technical Specifications . . . . . . . . . .12

Troubleshooting . . . . . . . . . . . . . . .13

Compliance Information . . . . . . . . .16

Part Number Port One - Copper Port Two - Duplex Fiber-Optic

SPSVT2611-100 Universal 26-pin

serial interface*

ST, 1300 nm multimode

2 km (1.2 miles)**

SPSVT2613-100 Universal 26-pin

serial interface*

SC, 1300 nm multimode

2 km (1.2 miles)**

SPSVT2614-100 Universal 26-pin

serial interface*

SC, 1310 nm single mode

20 km (12.4 miles)**

SPSVT2615-100 Universal 26-pin

serial interface*

SC, 1310 nm single mode

40 km (24.9 miles)**

* For typical maximum cable distance, see Cable Specifications section.

** Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network installation.

The chassis version of this Device is CPSVT26xx-10x. For more information, see the

user’s guide for the CPSVT26xx-10x on-line at www.transition.com

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

* For typical maximum cable distance, see the Cable Specifications section in this

manual.

** Typical maximum cable distance. Actual distance is dependent upon the physical

characteristics of the network installation.

Optional Accessories (sold separately)

Part Number Port One - Copper Port Two - Single Fiber-Optic

SPSVT2629-100 Universal 26-pin

serial interface*

SC, single mode 1310 TX / 1550nm RX

20 km (12.4 miles)**

SPSVT2629-101 Universal 26-pin

serial interface*

SC, single mode 1550 TX / 1310nm RX

20 km (12.4 miles)**

The SPSVT2629-100 and the -101 are intended to be installed in

the same network where one is the local Device and the other is the

remote Device.

SPSVT2629-102 Universal 26-pin

serial interface*

SC, single mode 1310 TX / 1550nm RX

40 km (24.8 miles)**

SPSVT2629-103 Universal 26-pin

serial interface*

SC, single mode 1550 TX / 1310nm RX

40 km (24.8 miles)**

The SPSVT2629-102 and the -103 are intended to be installed in

the same network where one is the local Device and the other is the

remote Device.

Part Number Description

SPS-2460-SA Optional External Power Supply; 24-60VDC Stand-Alone

Output: 12.25VDC @ 1.0 A

SPS-2460-PS Optional External Power Supply; 24-60VDC Piggy-back

Output: 12.25VDC @ 1.0 A

E-MCR-05 12-Slot Device Rack (includes universal internal power supply)

19.0" x 15.0" x 4.75" (483 mm x 381 mm x 121 mm)

WMBL Optional Wall Mount Brackets; 4.0 in. (102 mm)

WMBV Optional Vertical Mount Bracket; 5.0 in. (127 mm)

WMBD Optional DIN Rail Mount Bracket; 5.0 in. (127 mm)

WMBD-F Optional DIN Rail Mount Bracket (flat); 3.3in. (84 mm)

Cable Options

Supported Cable Options

The table below lists the interface standards and the cable options that are supported

for the SPSVT26xx-10x Device.

Each cable (available from Transition Networks) is 3 meters in length and has a

male universal 26-pin serial connector at one end. The connector at the other end is

listed in the table.

Maximum Cable Lengths

The table below lists the recommended maximum cable lengths for each of the cable

options at various data rates.

[email protected] -- Click the “Transition Now” link for a live Web chat. 3

Part Number Function Connector Type

35DTE-3 V.35 DTE 34-pin Rectangular Male

35DCE-3 V.35 DCE 34-pin Rectangular Female

21DTE-3 X.21 DTE 15-pin D-sub Male

21DCE-3 X.21 DCE 15-pin D-sub Female

232DTE-3 RS-232 DTE 25-pin D-sub Male

232DCE-3 RS-232 DCE 25-pin D-sub Female

449DTE-3 RS-449 DTE 37-pin D-sub Male

449DCE-3 RS-449 DCE 37-pin D-sub Female

530DTE-3 RS-530 DTE 25-pin D-sub Male

530DCE-3 RS-530 DCE 25-pin D-sub Female

Data Rate V.35, RS-449, or RS-530 X.21 RS232C

10 Mb/s 10 m (35 ft.) N/A N/A

6 Mb/s 19 m (65 ft.) N/A N/A

2 Mb/s 45 m (150 ft.) 15 m (50 ft.) N/A

1 Mb/s 90 m (300 ft.) 30 m (100 ft.) N/A

512 Kb/s 180 m (600 ft.) 60 m (200 ft.) N/A

256 kb/s 365 m (1200 ft.) 120 m (400 ft.) N/A

128 Kb/s 730 m (2400 ft.) 240 m (800 ft.) N/A

56 Kb/s 910 m (3000 ft.) 480 m (1600 ft.) 3 m (10 ft.)

1.2 Kb/s 910 m (3000 ft.) 910 m (3000 ft.) 15 m (50 ft.)

N/A = Not Applicable. The rates are not specified for the interface in question.

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation

CAUTION: Wear a grounding device and observe electrostatic discharge

precautions when setting the switches and jumpers. Failure to observe this caution

could result in damage to, and subsequent failure of, the Device.

Set the Terminal Timing Switch

The 16-position terminal timing switch, located on the side of the Device, allows

the network administrator to configure the Device for various network conditions.

To set the terminal timing switch, insert a small, flat-blade screwdriver or a similar

device into the recessed arrow on the switch. Gently rotate the switch to the

position required for the site installation.

This table lists the conditions for each setting of the terminal timing switch:

* Setting “F” overrides the software mode and sets the Device to asynchronous

mode.

Terminal Timing Switch Setting

0 - TT = Receive CLK 8 - 768 Kb/s

1 - 56 Kb/s 9 - 1024 Kb/s

2 - 64 Kb/s A - 1544 Kb/s

3 - 112 Kb/s B - 2048 Kb/s

4 - 128 Kb/s C - 3072 Kb/s

5 - 256 Kb/s D - 4096 Kb/s

6 - 384 Kb/s E - 6144 Kb/s

7 - 512 Kb/s F - Asynchronous Mode*

[email protected] -- Click the “Transition Now” link for a live Web chat. 5

Data Path

Internal

Logic

Normal Mode Loop-Back Mode

Data Path

Internal

Logic

Installation — Continued

Set the Loop-Back Switch

The loop-back switch is located on the front panel of the Device and is used to

debug network faults. (See “Troubleshooting” section for examples.)

To set the switch, use a small flat-blade screwdriver or a similar device.

Normal Set the switch to “Norm” for normal

operation.

Loop-back Set the switch to “Loop” to enable both

fiber and copper loop-back.

The two drawings below illustrate the data path for both normal mode and loop-

back mode:

TxD (1,14)

(To DCD on other Converter)

(From DCD on other Converter)

Loopback Mode

High Speed Serial Converter

RxD (5,18)

TxCE (2,15)

RxC (4,17)

TxC (3,16)

RTS (8,9)

CTS (10,11)

DTR(7,20)

DSR (12,25)

DCD (6,19)

LL(13)

Norm Loop

Normal Operation

Fiber & Copper Loop Back

The drawing below indicates the data path during loop-back mode for each of the

pins on the copper 26-pin connector.

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation — Continued

Set the Jumpers

The SPSVT26xx-10x has three jumpers located on the circuit board inside the

Device housing. To set any of the three jumpers:

1. Using a small screwdriver, remove the four (4) screws that secure the cover

and carefully remove the cover from the Device.

2. Locate the jumper(s) on the circuit board.

3. Using small needle-nosed pliers or similar device, move the jumper(s) to the

desired position(s).

4. Carefully replace the cover on the Device and replace the four (4) screws that

secure the cover to the Device.

Hardware/Software Jumper (J4)

The Hardware/Software jumper (J4) is located on the

circuit board and is the jumper that is nearest the rear

connector of the Device (see the photo to the right).

Hardware The terminal timing switch controls the

terminal timing function. The loop-back

switch controls the loop-back function.

Software The terminal timing switch and the loop-back

switch are disabled. These two functions are

controlled by the most-recently saved, on-

board microprocessor settings.

Note: Setting the terminal timing switch to “F” overrides the software mode and

sets the Device to asynchronous mode.

Remote Management

The SPSVT26xx-10x stand-alone Device can be remotely managed by the

CPSVT26xx-10x, the chassis version of the Device.

For example, a local CPSVT2611-100 Device (that is installed in a managed

Transition Networks PointSystem™ chassis) is connected, via fiber, to a remote

SPSVT2611-100 Device. An example of a managed single-fiber network has a

local CPSVT2629-100 Device connected, via fiber, to a remote SPSVT2629-101.

Note: In a managed network, both the local and remote Devices must be set to

“software” mode (see above).

For more information, see the SNMP section in the CPSVT26xx-10x user’s guide

on-line at: www.transition.com.

Software Mode

Hardware Mode

Rear Connector

[email protected] -- Click the “Transition Now” link for a live Web chat. 7

Installation — Continued

Receive (RX) Clock Polarity Jumper (J6)

The RX Clock Polarity jumper (J6), located near the front panel of the circuit board,

selects the polarity of the receive clock.

Position A The receive data is sampled on the rising

edge of the receive clock.

Position B The receive data is sampled on the falling

edge of the receive clock.

Transmit (TX) Clock Polarity Jumper (J7)

The TX Clock Polarity jumper (J7), also located near the

front panel of the circuit board, selects the polarity of the

transmit clock.

Position A The transmit data is sampled on the rising

edge of the receive clock.

Position B The transmit data is sampled on the falling

edge of the receive clock.

This drawing illustrates “rising edge” and “falling edge” for clock polarity.

Raising Edge Clock

Falling Edge Clock

Clock

Data

Clock

Data

Position B

Position A

Position B

Position A

J7- TX Clock Polarity Jumper

J6- RX Clock Polarity Jumper

Front Panel

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Installation — Continued

Install the Fiber Cable

1. Locate or build fiber optic cable with male, two-stranded TX to RX connectors

installed at both ends.

2. Connect the fiber cables to the SPSVT26xx-10x Device as described:

• Connect the male TX cable connector to the female TX port.

• Connect the male RX cable connector to the female RX port.

3. Connect the fiber cables to the other device (another Device, hub, etc.) as

described:

• Connect the male TX cable connector to the female RX port.

• Connect the male RX cable connector to the female TX port.

Install the Copper Cable

1. Connect the high-speed serial cable to the Device by connecting the cable’s

copper connector to the Device’s copper port.

2. Ensure that the cable screwlocks are tightened securely. Failure to observe this

caution could cause data transfer to fail.

3. Connect the other end of the high-speed serial cable to the other network

device (cable router, CSU, etc.).

TX TX

Device Device

[email protected] -- Click the “Transition Now” link for a live Web chat. 9

Installation — Continued

Power the Device

1. Install the power adapter cord to the back of the Device.

2. Connect the power adapter plug to AC power.

3. Verify that the Device is powered by observing the illuminated LED power

indicator light.

Consult the user’s guide for the Transition Networks SPS2460-xx DC external

power supply for powering the Device.

Operation

Status LEDs

Use the status LEDs to monitor the SPSVT26xx-10x Device operation in the

network.

PWR (on) The Device is connected to external power.

FL (on) The fiber link is up.

(flashing) The fiber link is in loop-back mode.

CL (on) The copper link is up.

(flashing) The copper link is in loop-back mode.

(In asynchronous mode, the CL LED may flash if the data rates fall below

300 cycles per second.)

Copper

Fiber

NO RM L OOP

PWR

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Cable Specifications

Fiber Cable

Bit Error Rate: <10-9

Single mode fiber (recommended): 9 µm

Multimode fiber (recommended): 62.5/125 µm

Multimode fiber (optional): 100/140, 85/140, 50/125 µm

SPSVT2611-100 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SPSVT2613-100 1300 nm multimode

Fiber Optic Transmitter Power: min: -19.0 dBm max: -14.0 dBm

Fiber Optic Receiver Sensitivity: min: -30.0 dBm max: -14.0 dBm

Link Budget: 11.0 dB

SPSVT2614-100 1310 nm single mode

Fiber-optic Transmitter Power: min: -15.0 dBm max: -8.0 dBm

Fiber-optic Receiver Sensitivity: min: -31.0 dBm max: -8.0 dBm

Link Budget: 16.0 dB

SPSVT2615-100 1310 nm single mode

Fiber Optic Transmitter Power: min: -8.0 dBm max: -2.0 dBm

Fiber Optic Receiver Sensitivity: min: -34.0 dBm max: -7.0 dBm

Link Budget: 26.0 dB

SPSVT2629-100 1310 nm (TX) / 1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SPSVT2629-101 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -13.0 dBm max: -6.0 dBm

Fiber-optic Receiver Sensitivity: min: -32.0 dBm max: -3.0 dBm

Link Budget: 19.0 dB

SPSVT2629-102 1310 nm (TX) / 1550 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

SPSVT2629-103 1550 nm (TX) / 1310 nm (RX) simplex

Fiber-optic Transmitter Power: min: -8.0 dBm max: -3.0 dBm

Fiber-optic Receiver Sensitivity: min: -33.0 dBm max: -3.0 dBm

Link Budget: 25.0 dB

The fiber optic transmitters on this device meet Class I Laser safety requirements per

IEC-825/CDRH standards and comply with 21 CFR1040.10 and 21CFR1040.11.

[email protected] -- Click the “Transition Now” link for a live Web chat. 11

Cable Specifications — Continued

Copper Cable

• Copper twisted-pair, 28 AWG, 120 Ohm, 12 pf/foot capacitance (max)

• Nominal DC resistance: 65.0 ohms per 1000 feet (each conductor)

• Shield type: Aluminum Foil-Polyester Tape/Braid Shield with drain wire

• Standard Cable length: 3 m (10 ft.)

The five high-speed serial cables (available from Transition Networks) that are

compatible with the 26-pin copper port on the SPSVT26xx-10x Device are the

following:

• RS-232

• RS-449

• V.35

• X.21

• RS-530

Note: Please refer to the cable specifications documentation on-line at

www.transition.com.

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

Technical Specifications

For use with Transition Networks Model SPSVT26xx-10x or equivalent.

Data Rate: 1.2 Kb/s to 10 Mb/s

Dimensions: 3.25" x 1.0" x 4.8" (82mm x 25mm x 122mm)

Weight: 10 oz. (283 g) approximately

Power Consumption: 5.0 Watts

MTBF (w/power supply): 41,660 hours (MIL-HDBK-217F)

114,580 hours (Bellcore)

Power Supply: 12.25VDC @ 1.0A, 100-240 VAC (~1.0A), 15W max

Environment: Tmra*: 0 to 50°C (32 to 122°F)

Storage Temperature: -15 to 65°C (5 to 149°F)

Humidity: 10 to 90%, non condensing

Warranty: Lifetime

*Manufacturer’s rated ambient temperature.

The information in this user’s guide is subject to change. For the most up-to-date

information on the SPSVT26xx-10x Device, see the user’s guide on-line at

www.transition.com.

Product is certified by the manufacturer to comply with DHHS Rule 21/CFR,

Subchapter J applicable at the date of manufacture.

CAUTION: Visible and invisible laser radiation when open. Do not stare into beam or

view directly with optical instruments.

CAUTION: Use of controls, adjustments or the performance of procedures other than

those specified herein may result in hazardous radiation exposure.

[email protected] -- Click the “Transition Now” link for a live Web chat.

Troubleshooting

If the Device fails, isolate and correct the fault by determining the answers to the

following questions and then taking the indicated action:

1. Is the PWR LED on the Device illuminated?

• Is the power adapter the proper type of voltage and cycle frequency for the

AC outlet?

• Is the power adapter installed in the Device and in the outlet?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 2.

2. Is the CL LED on the Device illuminated?

• Are the copper cables connected properly?

• Is the device attached to the Device via the copper cable working properly?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 3.

3. Is the FL LED on the Device illuminated?

• Check the fiber cables for proper connection.

• Verify that the TX and RX cables on the Device are connected to the RX and

TX ports, respectively, on the other device.

• Are both Devices (connected via the fiber cables) in the same mode

(synchronous or asynchronous)?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 4.

4. Are the CL and FL LEDs on the Device flashing (indicating loop-back

mode)?

• Disable the loop-back function. In hardware mode, set the loop-back switch

to NORM (normal). In software mode, click “disable” in the loop-back

function.

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

YES

• Proceed to step 5.

5. Is data transfer failing?

YES

• Are the clock input and output polarity correct?

• Are the correct copper cables installed for the data format?

• Is the mode on the other device correct (synchronous/asynchronous)?

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

• Proceed to step 6.

SPSVT26xx-10x

24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600

6. Is data transfer failing?

YES

• Verify the local copper connection by starting a local copper loop-back

(hardware mode: set the loop-back switch on the local Device to “loop”,

software mode: enter the local copper loop-back command) and then use a

bit error test unit to run a bit error test.

• Verify the local fiber connection by starting a remote fiber loop-back

(hardware mode: set the loop-back switch on the remote Device to “loop”,

software mode: enter the remote fiber loop-back command) and then use a

bit error test unit to run a bit error test.

• Verify the remote copper connection by starting a remote copper loop-back

(hardware mode: set the loop-back switch on the remote Device to “loop”,

software mode: enter the remote copper loop-back command) and then use

a bit error test unit to run a bit error test.

• Verify remote fiber connection by starting a local copper loop-back

(hardware mode: setting the loop-back switch on the local Device to

“loop”, software mode: enter the local fiber loop-back command) and then

use a bit error test unit to run a bit error test.

• Contact Tech Support: 800-260-1312, Int’l: 00-1-952-941-7600.

reppoCrebiFreppoC Local

Device

Remote

Device

reppoCrebiFreppoC Remote

Device

Local

Device

reppoCrebiFreppoC Local

Device

Remote

Device

reppoCrebiFreppoC Remote

Device

Local

Device

Declaration of Conformity

Name of Mfg: Transition Networks

10900 Red Circle Drive, Minnetonka MN 55343 U.S.A.

Model Number(s): SPSVT2611-100, SPSVT2613-100, SPSVT2614-100,

SPSVT2615-100, SPSVT2629-100, SPSVT2629-101,

SPSVT2629-102, SPSVT2629-103

Directive(s) and standard(s):

EMC Directive 2004/108/EC; EN 55022:2006+A1:2007 Class A;

EN55024:1998+A1:2001+A2:2003; EN6100-2-3; EN6100-3-3; CFR Title 47 Part 15

Subpart B Class A. Low Voltage Directive: 2006/95/EC; IEC 60950-1:2005; CFR

Title 21 Section 1040.10 Class I.

I, the undersigned, hereby declare that the model numbers listed in this declaration of

conformity conform to the Directive(s) and Standard(s) herein.

January 2012

Stephen Anderson, Vice-President of Engineering Date

[email protected] -- Click the “Transition Now” link for a live Web chat. 15

Technical Support

Technical support is available 24 hours a day.

US and Canada: 1-800-260-1312

International: 00-1-952-941-7600

Transition Now

Chat live via the Web with Transition Networks Technical Support.

Log onto www.transition.com and click the Transition Now link.

Web-Based Seminars

Transition Networks provides seminars via live web-based training.

Log onto www.transition.com and click the Learning Center link.

E-Mail

Ask a question anytime by sending an e-mail to our technical support staff.

[email protected]

Address

Transition Networks

10900 Red Circle Drive Minnetonka, MN 55343, U.S.A.

telephone: 952-941-7600

toll free: 800-526-9267

fax: 952-941-2322

Compliance Information

CISPR22/EN55022 Class A + EN55024

CE Mark

FCC Regulations

This equipment has been tested and found to comply with the limits for a Class A digital device,

pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This

equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference, in which

case the user will be required to correct the interference at the user's own expense.

Canadian Regulations

This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out

on the radio interference regulations of the Canadian Department of Communications.

Le présent appareil numérique n'émet pas de bruits radioélectriques dépassant les limites applicables

aux appareils numériques de la Class A prescrites dans le Règlement sur le brouillage

radioélectrique édicté par le ministère des Communications du Canada.

European Regulations

Warning

This is a Class A product. In a domestic environment this product may cause radio interference in

which case the user may be required to take adequate measures.

Achtung !

Dieses ist ein Gerät der Funkstörgrenzwertklasse A. In Wohnbereichen können bei Betrieb dieses

Gerätes Rundfunkstörungen auftreten. In diesem Fäll ist der Benutzer für Gegenmaßnahmen

verantwortlich.

Attention !

Ceci est un produit de Classe A. Dans un environment domestique, ce produit risque de créer des

interférences radioélectriques, il appartiendra alors à l'utilsateur de prende les measures spécifiques

appropriées.

Trademark Notice

All trademarks and registered trademarks are the property of their respective owners.

graphic, electronic, or mechanical - without written permission from Transition Networks.

Printed in the U.S.A.

33236.G

CAUTION: RJ connectors are NOT INTENDED FOR CONNECTION TO THE

PUBLIC TELEPHONE NETWORK. Failure to observe this caution could result in

damage to the public telephone network.

Der Anschluss dieses Gerätes an ein öffentlickes Telekommunikationsnetz in den EG-

Mitgliedstaaten verstösst gegen die jeweligen einzelstaatlichen Gesetze zur Anwendung der

Richtlinie 91/263/EWG zur Angleichung der Rechtsvorschriften der Mitgliedstaaten über

Telekommunikationsendeinrichtungen einschliesslich der gegenseitigen Anerkennung ihrer

Konformität.

In accordance with European Union Directive 2002/96/EC of the European Parliament and

of the Council of 27 January 2003, Transition Networks will accept post usage returns of

this product for proper disposal. The contact information for this activity can be found in

the 'Contact Us' portion of this document.

Table des matières

Autres manuels Transition Networks Convertisseur de média

Transition Networks

Transition Networks CSDTF3011-115 Manuel utilisateur

Transition Networks

Transition Networks CSDTF1011-105 Manuel utilisateur

Transition Networks

Transition Networks J/FE-CF-01(SC) Manuel utilisateur

Transition Networks

Transition Networks E-TX-SX-02 Manuel utilisateur

Transition Networks

Transition Networks CSDTF30xx-11x Manuel utilisateur

Transition Networks

Transition Networks TN-GB-xM5 Manuel utilisateur

Transition Networks

Transition Networks CSRFB10XX-100 Manuel utilisateur

Transition Networks

Transition Networks HSTR-CF-01(SC) Manuel utilisateur

Transition Networks

Transition Networks C/E-100BTX-FX-05(LH) Manuel utilisateur

Transition Networks

Transition Networks Milan Raven Series Manuel utilisateur

Transition Networks

Transition Networks SI-IES-111D-LRT Manuel utilisateur

Transition Networks

Transition Networks C/E-PSW-FX-03(LH) Manuel utilisateur

Transition Networks

Transition Networks CBFTF10xx-1xx Manuel utilisateur

Transition Networks

Transition Networks ARCNET C/AR-CF-02(SC) Manuel utilisateur

Transition Networks

Transition Networks SBFTF1011-120 Manuel utilisateur

Transition Networks

Transition Networks E-TBT-FRL-1007 Manuel utilisateur

Transition Networks

Transition Networks CPSVT26XX Manuel utilisateur

Transition Networks

Transition Networks SSDTF1011-105 Manuel utilisateur

Transition Networks

Transition Networks M/GE-ISW-SFP-01-PD Manuel utilisateur

Transition Networks

Transition Networks CFMFF1314-280 Manuel utilisateur

Transition Networks

Transition Networks 10BASE-2 Manuel utilisateur

Transition Networks

Transition Networks C/HSTR-CF-01(SC) Manuel utilisateur

Transition Networks

Transition Networks CETTF10XX-200 Manuel utilisateur

Transition Networks

Transition Networks METTF1011-120 Manuel utilisateur

Manuels Convertisseur de média populaires d'autres marques

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuel utilisateur

SPROLINK

SPROLINK VA1 Manuel utilisateur

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuel utilisateur

Nikon

Nikon AF-S TC-20E III Manuel utilisateur

Axis

Axis AXIS Q7406 Manuel utilisateur

Omega

Omega TAC80B-J Manuel utilisateur

Zoom

Zoom Thunderbolt TAC-2R Manuel utilisateur

OST

OST iConverter 10/100M Manuel utilisateur

Vertiv

Vertiv Netsure Manuel utilisateur

birddog

birddog MINI Manuel utilisateur

Roland

Roland GI-10 Manuel utilisateur

Wallenstein

Wallenstein WX310 Manuel utilisateur

Pace

Pace MSS 200-1 Manuel utilisateur

Solar Converters

Solar Converters EQ 12/24-50 Manuel utilisateur

CYP

CYP EL-7400V Manuel utilisateur

TIE

TIE MIDI 1i1o Manuel utilisateur

DCS

DCS Vivaldi Upsampler Manuel utilisateur

Westermo

Westermo MCW-211 SERIES Manuel utilisateur