TP-Link JetStream TL-SL3428 Manuel utilisateur

Installation Guide

L2 Managed Switch

TL-SL3428/TL-SL3452

Business Networking Solution

Specifications are subject to change without notice. is a registered trademark of TP-LINK

TECHNOLOGIES CO., LTD. Other brands and product names are trademarks of their respective holders.

No part of the specifications may be reproduced in any form or by any means or used to make any derivative such

as translation, transformation, or adaptation without permission from TP-LINK TECHNOLOGIES CO., LTD. Copyright

http://www.tp-link.com

FCC STATEMENT

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part

15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when

the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful

interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful

interference in which case the user will be required to correct the interference at his own expense.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1) This device may not cause harmful interference.

2) This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference, in which case the

user may be required to take adequate measures.

Related Document

The User Guide and CLI Reference Guide of the product are provided on the resource

CD.

To obtain the latest product information, please visit the official website:

http://www.tp-link.com

About this Installation Guide

This Installation Guide describes the hardware characteristics, installation methods and

the points that should be attended to during installation.

This Installation Guide is structured as follows:

Chapter 1 Introduction. This chapter describes the external components of the

switch.

Chapter 2 Installation. This chapter illustrates how to install the switch.

Chapter 3 Lightning Protection. This chapter illustrates how to prevent lightning

damage.

Chapter 4 Connection. This chapter illustrates how to do the physical connection of

the switch.

Chapter 5 Configuration. This chapter instructs you to configure the switch via Web

Interface and CLI commands.

Appendix A Troubleshooting.

Appendix B Hardware Specifications.

III

Audience

This Installation Guide is for:

Network Engineer

Network Administrator

Conventions

Due to the similarity in structure of the L2 managed switch series, in this Installation

Guide we take TL-SL3428 as an example to illustrate Chapter 2 Installation, Chapter 3

Lighting Protection, Chapter 4 Connection and Chapter 5 Configuration.

This guide uses the specific formats to highlight special messages. The following table

lists the notice icons that are used throughout this guide.

Remind to be careful. A caution indicates a potential which may

result in device damage.

Remind to take notice. The note contains the helpful

information for a better use of the product.

Audience

Contents

Chapter 1 Introduction ———————————— 01

1.1 Product Overview.........................................01

1.2 Appearance .................................................01

Chapter 2 Installation ————————————— 04

2.1 Package Contents.........................................04

2.2 Safety Precautions........................................04

2.3 Installation Tools ..........................................06

2.4 Product Installation ......................................06

Chapter 3 Lightning Protection ———————— 08

3.1 Cabling Reasonably ......................................08

3.2 Connect to Ground .......................................10

3.3 Equipotential Bonding...................................11

3.4 Use Lightning Arrester ..................................12

Chapter 4 Connection ————————————— 13

4.1 Ethernet Port ...............................................13

4.2 SFP Port ......................................................13

4.3 Console Port ................................................14

4.4 Verify Installation .........................................14

4.5 Power On ..................................................14

4.6 Initialization.................................................15

Chapter 5 Conguration———————————— 16

5.1 Congure the switch via GUI.........................16

5.2 Congure the switch Using CLI......................17

Appendix A Troubleshooting—————————— 19

Appendix B Hardware Specications —————— 20

L2 Managed Switch

Chapter 1 Introduction

1.1 Product Overview

TP-LINK JetStream L2 Managed switch, designed for workgroups and departments,

provides wire-speed performance and abundant layer 2 management features. It

provides a variety of service features and multiple powerful functions with high security.

The EIA-standardized framework and smart configuration capacity can provide flexible

solutions for a variable scale of networks. ACL, 802.1x and Dynamic ARP Inspection

provide robust security strategies. QoS and IGMP snooping/filtering optimize voice and

video application. Link aggregation (LACP) increases aggregated bandwidth, optimizing

the transport of business critical data. Web, CLI (Console Port, Telnet, SSH), SNMP and

RMON bring abundant management policies. TP-LINK JetStream L2 Managed switch

integrates multiple functions with excellent performance, and is friendly to manage,

which can fully meet the need of the users demanding higher networking performance.

1.2 Appearance

■Front Panel

The front panel of TL-SL3428 is shown as the following figure.

Figure 1-1 Front Panel of TL-SL3428

The front panel of TL-SL3452 is shown as the following figure.

Figure 1-2 Front Panel of TL-SL3452

Introduction

L2 Managed Switch

TL-SL3428

LEDs

Console Port

10/100/1000Mbps RJ45 Port

SFP Port

10/100Mbps RJ45 Port

30 32 34 36 38 40 42 44 46 48

246810 12 14 16 18 20 22 24 26 28 29 31 33

37 39 41 43 45 47

25 271 3579

11 13 15 17 19 21 23

Console

PWR

SYS

51 52

5-4-

100Mbps

10Mbps

1000Mbps

10/100Mbps

1000Base-X

LEDs

Console Port

10/100/1000Mbps RJ45 Port

SFP Port

10/100Mbps RJ45 Port

L2 Managed Switch

LEDs

LED Status Indication

PWR

On The switch is powered on

Off The switch is powered off or power supply is abnormal

Flashing Power supply is abnormal

SYS Flashing The switch works properly

On/Off The switch works improperly

10/100Mbps

On A device is linked to the corresponding port, but no activity

Flashing Data is being transmitted or received

Green A 100Mbps device is connected to the corresponding port

Yellow A 10Mbps device is connected to the corresponding port

Off No device is connected to the corresponding port

1000Mbps

On A device is linked to the corresponding port, but no activity

Flashing Data is being transmitted or received

Green A 1000Mbps device is connected to the corresponding port

Yellow A 10/100Mbps device is connected to the corresponding port

Off No device is connected to the corresponding port

Note: TL-SL3428 features some “Combo”ports. A “Combo”port consists of a RJ45

port and a SFP port, and the two ports share the same LED.

Port Feature

Model 10/100Mbps RJ45

Port

10/100/1000Mbps

RJ45 Port SFP Port Console Port

TL-SL 3428 24 4 2 1

TL-SL 3452 48 2 2 1

10/100Mbps Port

Designed to connect to the device with a bandwidth of 10Mbps or 100Mbps. Each

has a corresponding 10/100Mbps LED.

10/100/1000Mbps Port

Designed to connect to the device with a bandwidth of 10Mbps, 100Mbps or

1000Mbps. Each has a corresponding 1000Mbps LED.

SFP Port

Designed to install the SFP module.

TL-SL3428 features some SFP transceiver slots that are shared with the associated

RJ45 ports. The associated two ports are referred as a “Combo” port, which means

they cannot be used simultaneously, otherwise only SFP port works.

Console Port

Designed to connect with the serial port of a computer or terminal for monitoring

and configuring the switch.

Introduction

L2 Managed Switch

Note:

■For TL-SL3428, when using the SFP port with a 100Mbps module or a gigabit module,

you need log on to the GUI (Graphical User Interface) of the switch and configure its

corresponding Speed and Duplex mode on Switching→Port→Port Config page.

For 100Mbps module, please select 100MFD while select 1000MFD for gigabit module.

By default, the Speed and Duplex mode of SFP port is 1000MFD.

■For TL-SL3452, the SFP port can be only used with a gigabit module.

■Rear Panel

The rear panel of TL-SL3428 is shown as the following figure.

Grounding Terminal

Power Socket

Figure 1-3 Rear Panel of TL-SL3428

The rear panel of TL-SL3452 is shown as the following figure.

Grounding Terminal

Power Socket

Figure 1-4 Rear Panel of TL-SL3452

Grounding Terminal

The switch already comes with lightning protection mechanism. You can also ground

the switch through the PE (Protecting Earth) cable of AC cord or with Ground Cable.

For detailed information, please refer to Chapter 3 Lightning Protection.

Power Socket

Connect the female connector of the power cord here, and the male connector to

the AC power outlet. Please make sure the voltage of the power supply meets the

requirement of the input voltage (100-240V~ 50/60Hz).

Caution: Please use the provided power cord.

Introduction

L2 Managed Switch

Chapter 2 Installation

2.1 Package Contents

Make sure that the package contains the following items. If any of the listed items is

damaged or missing, please contact your distributor.

One Resource CD

One switch One Power Cord and one

Console Cable

This Installation Guide

Two mounting brackets and

the ttings

L2Managed Switch

TL-SL3428

2.2 Safety Precautions

To avoid any device damage and bodily injury caused by improper use, please observe

the following rules.

■Safety Precautions

■Keep the power off during the installation.

■Wear an ESD-preventive wrist strap, and make sure that the wrist strap has a good

skin contact and is well grounded.

■Use only the power cord provided with the switch.

■Make sure that the supply voltage matches the specifications indicated on the rear

panel of the switch.

■Ensure the vent hole is well ventilated and unblocked.

■Do not open or remove the cover of the switch.

■Before cleaning the device, cut off the power supply. Do not clean it by the waterish

cloth, and never use any other liquid cleaning method.

■Site Requirements

To ensure normal operation and long service life of the device, please install it in an

environment that meets the requirements described in the following subsection.

Temperature/Humidity

ȭ

ȭ

L2Managed Switch

TL-SL3428

Installation

L2 Managed Switch

Please keep a proper temperature and humidity in the equipment room. Too high/low

humidity may lead to bad insulation, electricity leakage, mechanical property changes

and corrosions. Too high temperature may accelerate aging of the insulation materials

and can thus significantly shorten the service life of the device. For normal temperature

and humidity of the device, please check the following table.

Environment Temperature Humidity

Operating 0℃~ 40℃10% ~ 90%RH Non-condensing

Storage -40℃~ 70℃5% ~ 90%RH Non-condensing

Clearness

L2Managed Switch

TL-SL3428

The dust accumulated on the switch can be absorbed by static electricity and result

in poor contact of metal contact points. Some measures have been taken for the

device to prevent static electricity, but too strong static electricity can cause deadly

damage to the electronic elements on the internal circuit board. To avoid the effect of

static electricity on the operation of the switch, please attach much importance to the

following items:

■Dust the device regularly, and keep the indoor air clean.

■Keep the device well grounded and ensure static electricity has been transferred.

Electromagnetic Interference

L2Managed Switch

TL-SL3428

Electronic elements including capacitance and inductance on the device can be affected

by external interferences, such as conducted emission by capacitance coupling,

inductance coupling, and impedance coupling. To decrease the interferences, please

make sure to take the following measures:

■Use the power supply that can effectively filter interference from the power grid.

■Keep the device far from high-frequency, strong-current devices, such as radio

transmitting station.

■Use electromagnetic shielding when necessary.

Lightening Protection

L2Managed Switch

TL-SL3428

Extremely high voltage currents can be produced instantly when lightning occurs and

the air in the electric discharge path can be instantly heated up to 20,000℃. As this

instant current is strong enough to damage electronic devices, more effective lightning

Installation

Autres manuels pour JetStream TL-SL3428

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels TP-Link Routeur réseau

TP-Link

TP-Link Auranet EAP220 Manuel utilisateur

TP-Link

TP-Link TD-W8961N Manuel utilisateur

TP-Link

TP-Link Archer AX10 Manuel utilisateur

TP-Link

TP-Link ARCHER C3150 Manuel utilisateur

TP-Link

TP-Link Archer C2300 Manuel utilisateur

TP-Link

TP-Link Archer VR400 Manuel utilisateur

TP-Link

TP-Link td-w8970 Manuel utilisateur

TP-Link

TP-Link TL-POE10E Manuel utilisateur

TP-Link

TP-Link Archer AXE200 Omni V1 Manuel utilisateur

TP-Link

TP-Link Omada ER706W Manuel utilisateur

TP-Link

TP-Link Archer C3200 Manuel utilisateur

TP-Link

TP-Link TL-R4000+ Manuel utilisateur

TP-Link

TP-Link TL-ER6020 Manuel utilisateur

TP-Link

TP-Link TL-ER604W Manuel utilisateur

TP-Link

TP-Link Archer C5 Manuel utilisateur

TP-Link

TP-Link BetterEnergy Manuel utilisateur

TP-Link

TP-Link RE200 Manuel utilisateur

TP-Link

TP-Link Archer C6 Manuel utilisateur

TP-Link

TP-Link TL-MR6400 Manuel utilisateur

TP-Link

TP-Link Archer C900 Manuel utilisateur

TP-Link

TP-Link Archer A20 Manuel utilisateur

TP-Link

TP-Link AXE5400 Manuel utilisateur

TP-Link

TP-Link Archer C2600 Manuel utilisateur

TP-Link

TP-Link TD-W300KIT Manuel utilisateur

Manuels Routeur réseau populaires d'autres marques

Allnet

Allnet ALL0333AU Manuel utilisateur

HomeSeer

HomeSeer HT-SEL Manuel utilisateur

Sercomm

Sercomm Genesis OC3505D Manuel utilisateur

Billion

Billion BIPAC 5102 Series Manuel utilisateur

Motorola

Motorola MR1900 Manuel utilisateur

Digi

Digi IX14 Manuel utilisateur

Cisco

Cisco NCS 540 Manuel

XAVi

XAVi X8821e Manuel utilisateur

BEC

BEC 6200WZL Manuel utilisateur

MikroTik

MikroTik hAP ac3 Series Manuel utilisateur

Korenix

Korenix JetNet 5428G Series Manuel utilisateur

NETGEAR

NETGEAR FS526T - Switch Manuel utilisateur

Korenix

Korenix JetNet 5710G Series Manuel utilisateur

Automated Logic

Automated Logic ZN551 Manuel du propriétaire

Cisco

Cisco ASR 1000 Series Manuel de l'opérateur

EnGenius

EnGenius ESR-9710 Manuel utilisateur

Cisco

Cisco 805 Series Instructions d'utilisation et de sécurité

LevelOne

LevelOne FBR-1416 Manuel utilisateur