TouchIT LED Duo Manuel utilisateur
TouchIT LED Duo
Manual
TouchIT Technologies, Inc
Chapter 1
TouchIT LED
Duo
Inside the manual you will learn all about the
TouchIT LED Duo models of Interactive LED.
For more information, please visit
www.touchittechnologies.com
IMPORTANT SAFETY INSTRUCTIONS
1. Please read these instructions carefully before using the product and keep them
safe for later reference.
2. Follow all warnings and instructions marked on the product.
3. Unplug this product from the wall outlet (power socket) before cleaning. Clean
the product with a damp soft cloth. Do not use liquid or aerosol cleaners as it may
cause permanent damage to the screen.
4. Caution of use varies from model to model; please observe appropriate
operation as per model in use.
5. Do not place this product on an unstable cart, stand, or surface which may
cause damage or harm to the product or individual.
6. Slots and openings on the cabinet, in the back cover or in the bottom, are for
ventilation; to ensure reliable operation and to prevent from overheating, these
openings must not be blocked or covered at any time. The openings should never
be placed near or over a radiator, heat source, or placed in a built-in installation
unless proper ventilation space (min. 2 inches/5cm of gap) is provided.
Section 1
IMPORTANT SAFETY INSTRUCTIONS
Please read these instructions carefully before
using the product and keep them safe for
future reference.
PLEASE NOTE :-
The TouchIT LED Duo has been designed to
be a MONITOR and NOT a Television. It does
not contain a TV Tuner of any description.
Safety Instructions
2
7. This product should be operated from the type of power
indicated on the marking label. If you are not sure of the type of
power available, consult your dealer or local service company.
8. This product is equipped with a 3-wire grounding type power
plug, a plug having a third (grounding) pin. This plug will only fit
into a grounding-type power outlet. This is a safety feature. If you
do not have proper outlet to insert the plug, contact your
electrician to replace your obsolete outlet. Do not break the
ground pin and circumvent the grounding.
9. Do not allow anything to rest, or persons to walk on the power
cord.
10. If an extension cord is used with this product, make sure that
the total ampere rating plugged into the extension cord does not
exceed the maximum ampere rating of the extension cord.
11. Never insert any object/tool of any kind through housing slots
of this product as they may touch dangerous voltage points or
short out components that could result in risk of fire or electric
shock. Never spill liquid of any kind on the product (except IP-
rated models).
12. Do not attempt to service this product yourself, always refer
to qualified or authorized person for the servicing of this product.
13. Unplug this product from the wall outlet and contact a
qualified service provider in the following circumstances:
When the power cord or plug is damaged, frayed or broken.
In the event that liquid has been spilled into the product (except
IP-rated models).
3
1-1!About the Product
The TouchIT LED Duo is made of TFT LED panel and microprocessor-controlled
main board. It is designed to meet the demanding performance requirements of
education/schools, public premises, corporate, and industrial applications.
1-2!Notice
1.!Do not use any sharp object on the original LED panel surface if the model is
supplied without protective glass.
2.!Do not use corrosive or abrasive detergents, waxes or solvents for cleaning.
Use only a dry or damp cloth and use with clean water when cleaning.
3.!Use qualified and safety-approved AC power cord only.
1-3!Check List
When opening the carton, please make sure that all the items listed below are
present:
Section 2
CHAPTER CONTENTS
1-1!About the Product
1-2!Notice
1-3!Check List
Introduction
4
1.!VGA cable (male-to-male) ×1
2.!Power cord ×1
3.!USB cable ×1
4.!Software CD
5. Remote control x 1, batteries included
6. VGA Cable
7. 3.5mm Audio Cable
If any items are missing or damaged, please contact your dealer
immediately.
Following items are optional and may be ordered separately:
8.!DVI cable (optional)
9.!RS232 to RS485 adapter(optional)
9.!HDMI-to-DVI adapter (optional)
5
2-1 Power & Signal Connections
2-1-1. Power cord connection:
Connect the power cord to the AC outlet.
2-1-2. Power on:
Switch on the main power of your TouchIT LED Duo (switch is located next to the
AC outlet)
2-1-3. VGA Signal cable connection:
Plug one end of the 15-pin signal cable (VGA) to the video signal connector at the
rear of the PC system (or engine box) and the other end to the TouchIT LED Duo.
Secure the connectors with the screws on the cable connector at both ends.
A HDMI Cable may be used as an alternative
Section 3
POWER AND SIGNAL CONNECTIONS
2-1-1. Power cord connection
2-1-2. Power on
2-1-3. VGA Signal cable connection
2-2 Optional Connections
2-2-1 DVI connection (optional cable)
2-2-2 VGA output connection (Optional male
to male VGA cable)
2-2-3 USB cable connection (for touch
TouchIT LED Duo models)
Installing the TouchIT LED Duo
6
2-2 Optional Connections:
This TouchIT LED Duo is designed to work with second signal
source. Please enter OSD menu to switch between these signal
sources and other adjustments
2-2-1 DVI connection (optional cable):
Plug one end of the DVI signal cable to signal source (PC, or, IPC,
or, media player of any kind with proper DVI out port), and the
other end to the DVI connector on the TouchIT LED Duo. Tighten
the connector screws on both ends of the cable to secure good
signal connection.
2-2-2 VGA output connection (Optional male to male VGA
cable):
Plug one end of the VGA signal cable to signal source and the
other end to another VGA in connector to daisy-chain, or
establish a cascading signal to the other TouchIT LED Duo.
Tighten the connector screws on both ends of the cable to ensure
a good signal.
2-2-3 USB cable connection
Plug one end of the USB cable to the USB connector at the rear
of the (PC, or, IPC, or, media player), and the other end to the
USB connector on TouchIT LED Duo.
7
3-1 Get to know the monitor
The Monitor connectors are located on the rear side. They are shown in the
physical monitor as per the figure below and described in the following
paragraphs. Please note that connectors may vary in some derivative models,
please refer to individual model for special instructions.
!
Section 4
USING THE LED
3-1 Get to know the LED
3-2 Connector ports
3-3 Remote Control
3-4 Understanding the OSD Menu (with
Remote control)
3-5 Understanding the Keypad
Using the TouchIT LED Duo
8
3-2 Connector ports
The Figure below depicts the signal connectors on the main
board.
!
3-3 Remote Control
The remote control is shown in the drawing below.
!
Size: 197.2 x 47.1 x 23.2mm
Operation distance: > 10 meter
Working angle: not more then +/- 40 degree
3-4 Understanding the OSD Menu (with Remote control)
a. Power
Press the power button to turn on/offthe monitor.
b. HDMI 1
Press this button to enter HDMI 1signal source.
c. HDMI 2
Press this button to enter HDMI 2signal source.
d. Ypbpr
9
Table des matières
Manuels Carte mère populaires d'autres marques
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuel utilisateur
Gigabyte
Gigabyte GA-9IVDT Manuel utilisateur
Texas Instruments
Texas Instruments ADS8372EVM Manuel utilisateur
Commell
Commell MS-C73 Manuel utilisateur
IBT Technologies
IBT Technologies MB860 Manuel utilisateur
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur
