Toshiba E3 Manuel utilisateur

E3 Adjustable Speed Drive

Engineering Specification

PART 1 - GENERAL

1.0 Scope

This specification shall cover Toshiba E3 AC Variable Frequency Drives, 6 pulse for

230V and 460V.

1.1 References

A. National Electric Manufactures Association (NEMA)

B. Underwriters Laboratories, Inc. (UL) and CSA

C. National Electric Code (NEC)

D. IEEE 519. Compliance of IEEE 519 can be determined after Toshiba performs a

harmonics analysis. The analysis will be done after we receive a completed

harmonics questionnaire.

E. ISO 9001

1.2 Submittal

Submittals shall include Toshiba standard operation manual. Schematics can be obtained

from factory upon request.

PART 2 – E3 VARIABLE FREQUENCY DRIVE

2.0 General

A. This specification covers AC adjustable frequency drives for HVAC applications.

B. The manufacturer shall not have less than fifteen years of experience in the

manufacture of VFD’s.

C. The manufacturer shall manufacture both AC drives and motors at the same

facility.

D. The drive shall be manufactured in the United States.

2.1 Design Criteria

A. The drive should be a PWM (Pulse Width Modulated) transistorized inverter

using IGBT’s (Insulated Gate Bipolar Transistors) and must be fully digital.

B. The drive shall utilize Insulated Gate Bipolar Transistor (IGBT’s) in its power

section.

C. The E3 VFD shall have 3 basic design criteria

1) Rectifier Section that shall include diode bridge rectifier to convert AC to

DC.

2) Filtering Section that shall include capacitors to eliminate “ripple” affect on

the DC bus to produce smooth DC bus voltage.

3) Switching Section that shall included Insulated Gate Bipolar Transistors

(IGBT) to provided Pulse Width Modulation.

2.2 Ratings and overload capability of the VFD

A. The drive main input power shall be:

I. 200V/50Hz or 200V-230V/60Hz for 230V models

II. 380V-415V/50Hz or 400V-460V/60Hz for 460V models

B. The drive shall have a tolerance for voltage ±10% and frequency ±2Hz.

C. The drive overload current shall be 100% continuous and 110% for 1 minute.

D. The drive should have a common design for all horsepower models:

230V – 3 through 60HP

460V – 5 through 125HP

2.3 Control Features

A. The drive shall have True Torque Control with Automatic energy-saving control.

B. The drive shall have two (2) frequency priority selection feature.

C. The drive shall be capable of setting both upper and lower limit frequencies.

D. The ASD shall automatically adjust the PWM carrier frequency proportional to

speed. The range of automatic adjustment shall vary from 15khz to .5khz. The

minimum acceptable full speed carrier frequency (60 Hz) with no derating shall

be 8 kHz.

E. The drive shall be capable of PID set point control.

F. Preset macros for typical HVAC applications such as pumps, fans, cooling

towers.

G. Serial RS232C communications standard.

H. Automatic cooling fan control based on heat sink temperature for extended fan

life.

I. The drive shall be able to start and stop from a two-wire control (dry contacts),

three wire momentary contact closure, keypad, and serial interface.

J. The drive shall be able to act as a space heater for a motor when the system is not

running.

K. The drive shall have adjustable input and output terminal response time selections

to prevent noise effects and chattering.

L. The drive shall have a built-in control system for commercial power/inverter

power switching.

M. The drive shall have an adjustable retry function after a fault. Both number of

attempts (at least 10) and time between (1-10 sec).

N. The drive shall have an adjustable output short circuit detection selection for

standard motor and high-speed motors (very low inductance).

O. The drive shall have two programmable: volt per hertz patterns, maximum output

frequencies, electronic thermal protection settings, stall protections, base

frequencies, voltage boosts, and stall protection selections which can be chosen

while running to run motor A or motor B.

P. The drive shall have an analog input filter adjustment to limit the effects of noise

on the control signal.

Q. The drive shall permit switching between local/remote operation as well as

manual/auto “on the fly.”

R. The drive shall have the ability to ignore run commands until a “dampers open”

signal is received. In the event a “dampers open” signal is absent the drive shall

be capable providing a “close damper” signal. Upon receipt of “drive stop” signal

The ASD shall be capable of providing a close damper signal.

S. The drive shall be provided with “anti-windmilling” or “motor shaft stationary

control”

T. The drive shall have the following user selectable contingencies in the event of

loss of analog control signal while the drive is running before loss:

i. Run at the user set lower frequency limit.

ii. Run at the user set upper frequency limit.

iii. Trip with a signal loss fault.

iv. Run at user-selected percentage of the last valid frequency signal.

2.4 Operational Functions

A. The drive shall contain two separate acceleration/deceleration times with auto

tuning for optimum setting (0.1 to 6000 seconds) with choice of linear, S, or C

curves.

B. The drive shall be equipped with both local/remote and manual/auto keys on

touch pad.

C. The drive shall be equipped with a quick setup key with 18 most frequently

parameters in a HVAC type application.

D. The drive shall contain fifteen preset speeds, which can be activated from the

keypad, terminal inputs, and host computer.

E. The drive shall have the capability of storable special custom user setting.

F. The drive shall restart into a rotating motor operating in either the forward or

reverse direction and match that frequency.

G. The drive shall have adjustable soft stall (10% - 150%) which reduces frequency

and voltage of the inverter to sustain a run in an overload situation.

H. The drive shall be capable of performing a time base pattern run using 4 groups of

8 patterns each using the 15 preset speed values for a maximum of 32 different

patterns.

I. The drive shall have adjustable UL listed electronic overload protection (10% -

100%).

J. The drive shall have a custom programmable volt/hertz pattern.

2.5 Input / Output Capabilities

A. The drive shall accept the following frequency commands signals:

1) 3kΩpotentiometer (1kΩto 10KΩpotentiometer connection also

possible)

2) 0 to 10 Vdc (Input impedance Zin:33kΩ)

3) 0 to ±10 Vdc (Zin:67kΩ),

4) 0 to ±5 Vdc (Zin:34kΩ)

5) to 20mA (Zin:500Ω),

6) 15 Preset speeds

7) Motorized speed pot.

B. The drive shall have 2 programmable analog outputs programmable to 17 choices.

C. The drive shall have 1 programmable relay output programmable to 67 choices.

D. The drive shall have 8 programmable digital inputs programmable to 54 choices.

E. The drive shall have a pulse train output proportional to frequency (48,96,360

times frequency).

2.6 Protective Features

A. The drive shall contain three critical frequency jump points with individual

bandwidth.

B. The drive shall be UL rated for 200,000 AIC without the use of input fuses.

C. All drives 460V, 25HP and above shall be equipped with a 3% impedance DC

link.

D. The drive shall have external fault input.

E. The drive shall be capable of re-setting faults remotely and locally.

F. The drive shall be programmable to alert the following alarms:

1) Over torque alarm,

2) Inverter overload pre-alarm

3) Motor overload pre-alarm

4) Braking resistor overload pre-alarm

5) Inverter overheat pre-alarm

6) Undercurrent alarm

7) Over current pre-alarm

8) Communication error alarm

9) Cumulative timer alarm

10)Executing retry

G. The drive shall identify and display the following 33 faults:

1) Over current during acceleration trip

2) Over current during deceleration trip

3) Over current during normal run trip

4) Over current on the DC Bus during acceleration trip

5) Over current on the DC Bus during deceleration trip

6) Over current on the DC Bus during normal run trip

7) Load end over current trip detected at start-up (output terminals, motor

wiring, etc.)

8) U-phase short circuit trip detected at start-up

9) V-phase short circuit trip detected at start-up

10)W-phase short circuit trip detected at start-up

11)Overvoltage during acceleration trip

12)Overvoltage during deceleration trip

13)Overvoltage during normal (constant speed) run trip

14)Inverter overloaded trip

15)Motor overloaded trip

16)Inverter overheat trip

17)Emergency off trip message.

18)EEPROM failure during write cycle

19)EEPROM abnormality during initial reading

20)RAM error

21)ROM error

22)CPU error

23)Communication interruption error

24)Gate array error

25)Output current detection circuit error

26)Option PCB error trip

27)Low operating current trip

28)Main circuit under voltage trip

29)Over torque trip

30)Software detected earth fault trip

31)Hardware detected earth fault trip

32)Inverter type form mismatch error

33)EEPROM type form mismatch error

2.7 Operating Panel and Monitor Functions

A. The drive digital display shall be capable of monitoring the following 18

functions:

1) Post Compensation Output Frequency

2) Frequency Command Setting

3) Output Current

4) Input Voltage

5) Output Voltage

6) Torque Current

7) Excitation Current

8) PID Feedback Value

9) Motor Overload Ratio

10)Drive Overload Ratio

11)DBR Overload Ratio

12)Input Power

13)Output Power

14)RR Input Value

15)Peak Load Current

16)Peak Input Voltage

17)Kilowatt Hours

18)Megawatt Hours

B. The drive shall have 320 programmable parameters, which can be changed, while

the drive is in run mode.

C. The drive’s 353 parameters shall be adjustable from the 8 key touchpad or

computer link.

D. The drive shall be controlled through Palm-Pilot software.

E. The drive’s 11 key touchpad shall be NEMA 12 rated.

F. The drive’s keypad shall be capable of being extended 15 feet from the drive.

G. The drive shall contain a reset of all parameters to factory default settings or user

defaults (whichever one is chosen).

H. The drive shall have an elapsed time meter and will save the past four faults in

memory.

2.8 Optional features

A. 12-pulse diode rectification for maximum harmonics attenuation shall be

available for 460V drives 25HP through 100HP.

B. Pneumatic interface (3-15psi) transducers are available upon request.

C. Isolated input and output transducers are available upon request.

D. All drives regardless of size/voltage should have isolated bypass capability as an

available option.

E. 600V, E3 drives are also available from 5HP to 125HP. The ratings shall be

540V-660V/60 Hz for 600V models.

Communication options to include:

1) Metasys, N2 Interface

2) Landis-Steaffa, P1 Interface

3) RS485

4) Modbus RTU

5) Modbus+

6) Devicenet

7) AB RIO

8) Profibus DP

9) Lonworks

2.9 Drive Environmental Conditions

A. Environment - Indoors NEMA 1 metal enclosure, plastic shall not be acceptable.

B. Ambient temperature - 14°F to 104°F (up to 122°F with cover removed).

C. Altitude - 3,300 feet maximum without derating.

D. Relative humidity - 95% maximum (no condensation allowed).

E. Vibration - 0.5G maximum.

Part 3 – Start-up, Training and Warranty

A. Start-up and service is available as an additional option

B. The drive manufacturer shall guarantee the operation of the drive against failure

due to defects for 30 months after shipment or 24 months of service, whichever

comes first.

C. If factory authorized personnel perform the startup of the drive the standard

warranty is increased to 24 months.

D. The drive manufacturer shall supply a recommended list of spare parts and pricing

through our spare parts list book.

Autres manuels pour E3

Table des matières

Autres manuels Toshiba Matériel informatique

Toshiba

Toshiba DA364/DA374 Manuel utilisateur

Toshiba

Toshiba Libretto 50CT Manuel utilisateur

Toshiba

Toshiba Satellite L3xW-B Series Manuel du propriétaire

Toshiba

Toshiba Stratagy Flash Manuel utilisateur

Toshiba

Toshiba TPCS8209 Manuel utilisateur

Toshiba

Toshiba TCB-PCIN3E Manuel utilisateur

Toshiba

Toshiba Desk Station V Plus Manuel utilisateur

Toshiba

Toshiba TMP92CM22FG TLCS-900/H1 Series Manuel utilisateur

Toshiba

Toshiba TX49 TMPR4937 Manuel utilisateur

Toshiba

Toshiba ETB004Z Manuel utilisateur

Toshiba

Toshiba G7 Manuel utilisateur

Toshiba

Toshiba BCN002Z Manuel utilisateur

Toshiba

Toshiba TOSVERT VF-MB1 Manuel de la liste des pièces

Toshiba

Toshiba H9 Manuel utilisateur

Toshiba

Toshiba TCB-PSMT1E Manuel utilisateur

Toshiba

Toshiba AD368 Manuel utilisateur

Toshiba

Toshiba CEX0122B Manuel utilisateur

Toshiba

Toshiba nv-pack JTLI41 Manuel utilisateur

Toshiba

Toshiba ETB003Z Manuel utilisateur

Toshiba

Toshiba SD-BT00A Manuel utilisateur

Toshiba

Toshiba TOSVERT VF-MB1/S15 IPE002Z Manuel de la liste des pièces

Toshiba

Toshiba Memory Module Manuel de la liste des pièces

Toshiba

Toshiba G7 Mode d’emploi

Toshiba

Toshiba TX39 Series Manuel utilisateur

Manuels Matériel informatique populaires d'autres marques

EMC2

EMC2 VNX Series Manuel du propriétaire

Panasonic

Panasonic DV0PM20105 Manuel utilisateur

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuel utilisateur

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuel utilisateur

Raidon

Raidon iT2300 Manuel utilisateur

National Instruments

National Instruments PXI-8186 Manuel utilisateur

Hauppauge

Hauppauge WinTV-HVR-2250 Manuel utilisateur

Kontron

Kontron CP6002 Manuel utilisateur

Manhattan

Manhattan 702843 Manuel utilisateur

Aphex

Aphex 230 Manuel utilisateur

AMD

AMD Phenom II Manuel d'exploitation

Intel

Intel NUC 12 Pro Manuel utilisateur

dbx

dbx Zone Pro 1260 Manuel utilisateur

Galaxy

Galaxy GHDX2-2430S-24F4D Manuel utilisateur

Intel

Intel AXXRMFBU4 Manuel utilisateur

Kontron

Kontron DIMM-PC/MD Manuel utilisateur

ST X-NUCLEO-SAFEA1B Mode d'emploi

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuel utilisateur