Toro 03410TE Manuel utilisateur

OPERATOR’S

MANUAL

FORM NO. 3318-231 GB Rev A

MODEL NO. 03410TE—70001 & UP



REELMASTER®216

©The Toro Company—1996

Table of Contents

This operator's manual has instructions on safety, operation, and maintenance.

This manual emphasizes safety, mechanical and general product information. DANGER, WARNING and CAUTION

identify safety messages. Whenever the triangular safety alert symbol appears, understand the safety message that

follows. “IMPORTANT” highlights special mechanical information and “NOTE” emphasizes general product infor-

mation worthy of special attention.

IDENTIFICATION AND ORDERING

MODEL AND SERIAL NUMBER

The model and serial number for the traction unit is on a plate that is mounted on the left front frame member. The

model and serial number for the cutting unit is on a plate that is mounted on the top front of the center cutting unit.

Use model and serial number in all correspondence and when ordering parts.

To order replacement parts from an authorized TORO Distributor, supply the following information:

1. Model and serial numbers of the machine.

2. Part number, description and quantity of parts desired.

NOTE: Do not order by reference number if a parts catalog is being used; use the part number.

Page

Safety 3

Specifications 9

Before Operating 10

Controls 13

First-Time Operation 16

Operating 20

Maintenance 23

Safety

Training

1. Read the instructions carefully. Be familiar with

the controls and the proper use of the equipment.

2. Never allow children or people unfamiliar with

these instructions to use the lawn mower. Local

regulations may restrict the age of the operator.

3. Never mow while people, especially children, or

pets are nearby.

4. Keep in mind that the operator or user is responsi-

ble for accidents or hazards occurring to other

people or their property.

5. Do not carry passengers.

6. All drivers should seek and obtain professional

and practical instruction. Such instruction should

emphasize:

• the need for care and concentration when

working with ride-on machines;

• control of a ride-on machine sliding on a

slope will not be regained by the application

of the brake. The main reasons for loss of

control are:

– insufficient wheel grip;

– being driven too fast;

– inadequate braking;

– the type of machine is unsuitable for its

task;

– lack of awareness of the effects of

ground conditions, especially slopes;

– incorrect hitching and load distribution.

Preparation

1. While mowing, always wear substantial footwear

and long trousers. Do not operate the equipment

when barefoot or wearing open sandals.

2. Thoroughly inspect the area where the equipment

is to be used and remove all objects which may

be thrown by the machine.

3. WARNING—Petrol is highly flammable.

• Store fuel in containers specifically designed

for this purpose.

• Refuel outdoors only and do not smoke

while refueling.

• Add fuel before starting the engine. Never

remove the cap of the fuel tank or add petrol

while the engine is running or when the

engine is hot.

• If petrol is spilled, do not attempt to start the

engine but move the machine away from the

are of spillage and avoid creating any source

of ignition until petrol vapors have dissipat-

ed.

• Replace all fuel tanks and container caps

securely.

4. Replace faulty silencers.

Operation

1. Do not operate the engine in a confined space

where dangerous carbon monoxide fumes can col-

lect.

2. Mow only in daylight or in good artificial light.

3. Before attempting to start the engine, disengage

all blade attachment clutches and shift into neu-

tral.

4. Do not use on slopes of more than:

• Never mow side hills over 5°

• Never mow uphill over 10°

• Never mow downhill over 15°

5. Remember there is no such thing as a “safe”

slope. Travel on grass slopes requires particular

care. To guard against overturning:

Safety

• do not stop or start suddenly when going up

or downhill;

• engage the clutch slowly, and always keep

the machine in gear, especially when travail-

ing downhill;

• machine speeds should be kept low on

slopes and during tight turns;

• stay alert for bumps and hollows and other

hidden hazards;

• never mow across the face of the slope,

unless the lawn mower is designed for this

purpose.

6. Use care when pulling loads or using heavy

equipment.

• Use only approved drawbar hitch points.

• Limit loads to those you can safely control.

• Do not turn sharply. Use care when revers-

ing.

• Use counterweight(s) or wheel weights

when suggested in the instruction handbook.

7. Watch out for traffic when crossing or near road-

ways.

8. Stop the blades rotating before crossing surfaces

other than grass.

9. When using any attachments, never direct dis-

charge of material toward bystanders nor allow

anyone near the machine while in operation .

10. Never operate the lawn mower with defective

guards, shields or without safety protective

devices in place.

11. Do not change the engine governor settings or

overspeed the engine. Operating the engine at

excessive speeds may increase the hazard of per-

sonal injury.

12. Before leaving the operator’s position:

• disengage the power take-off and lower the

attachments;

• change into neutral and set the parking

brake;

• stop the engine and remove the key.

13. Disengage the drive to attachments when trans-

porting or not in use.

14. Stop the engine and disengage the drive to the

attachment

• before refueling;

• before removing the grass catcher;

• before making height adjustments unless the

adjustment can be made from the operator’s

position.

• before clearing blockages;

• before checking, cleaning or working on the

lawnmower;

• after striking a foreign object. Inspect the

lawnmower for damage and make repairs

before restarting and operating the equip-

ment.

15. Reduce the throttle setting during engine runout

and, if the engine is provided with a shutoff

valve, turn the fuel off at the conclusion of mow-

ing.

Maintenance and Storage

1. Keep all nuts, bolts and screws tight to be sure

the equipment is in safe working condition.

2. Never store the equipment with petrol in the tank

inside a building where fumes may reach an open

flame or spark.

3. Allow the engine to cool before storing in any

enclosure.

4. To reduce the fire hazard, keep the engine,

silencer, battery compartment and petrol storage

area free of grass, leaves, or excessive grease.

5. Check the grass catcher frequently for wear or

deterioration.

Safety

6. Replace worn or damaged parts for safety.

7. If the fuel tank has to be drained, this should be

done outdoors.

8. Be careful during adjustment of the machine to pre-

vent entrapment of the fingers between moving

blades and fixed parts of the machine.

9. On multi-bladed machines, take care as rotating

one blade can cause other blades to rotate.

10. When the machine is to be parked, stored or left

unattended, lower the cutting means unless a posi-

tive mechanical lock is used.

Sound &Vibration Levels

Sound Levels

This unit has an equivalent continuous A-weighted

sound pressure at the operator ear of: 90 dB(A), based

on measurements of identical machines per SAE

J1174—Mar 85 procedures.

This unit has a sound power level of 105 dB(A)/1pW,

based on measurements of identical machines per proce-

dures outlined in Directive 79/113/EEC and amend-

ments

Vibration Levels

This unit has a vibration level of 7.5 m/s2at the posteri-

or, based on measurements of identical machines per

ISO 2631 procedures.

This unit does not exceed a vibration level of 0.9 m/s2at

the posterior based on measurements of identical

machines per ISO 2631 procedures.

Symbol Glossary

Caustic liquids, 

chemical burns to 

fingers or hand

Poisonous 

fumes or toxic 

gases, asphyxiation

Electrical shock,

electrocution High pressure

fluid, injection 

into body

High pressure

spray, erosion of

flesh

High pressure

spray, erosion of

flesh

Crushing of 

fingers

or hand, 

force

applied from 

above

Crushing of 

toes or foot, force

applied from above

Crushing of 

whole body, 

applied from 

above

Crushing of 

torso, force 

applied from side

Crushing of fingers 

or hand/, force 

applied from side

Crushing of 

whole body Crushing of 

head, torso and 

arms

Cutting of 

fingers or hand Cutting of footCrushing of leg, 

force applied 

from side

Cutting or 

entanglement of 

foot, rotating auger

Severing of 

foot, rotating 

knives

Severing of 

fingers or hand, 

impeller blade

Wait until all 

machine 

components have 

completely stopped 

before touching them

Severing of

fingers or hand, 

engine fan

Whole body entanglement, 

implement input drive line Fingers or 

hand entangle-

ment, chain drive

Runover/back-

over, (relevant 

machine to appear 

in dashed box)

Machine tipping, 

riding mower Machine rollover,

ROPS (relevant 

machine to appear 

in dashed box)

Stored energy

hazard, kickback

or upward motion

Hot surfaces, 

burns to fingers 

or hands

Hand & arm

entanglement,

belt drive

Thrown or fly-

ing objects, whole

body exposure

Thrown or 

flying objects, 

face exposure

Explosion Fire or open 

flame

Secure lifting 

cylinder with locking 

device before getting 

in hazardous area

Stay a safe 

distance from 

the machine

Stay clear of 

articulation area 

while engine is 

running

Do not open 

or remove safety 

shields while 

engine is 

running

Do not step on 

loading platform if 

PTO is connected to tractor 

& engine is running

Do not step

Shut off engine 

& remove key before 

performing mainten-

ance or repair work

Riding on this 

machine is allowed 

only on a passen-

ger seat & only if the 

driver’s view is not 

hindered

Consult 

technical manual 

for proper service 

procedures

Fasten seat belts Safety alert 

triangle outline safety

alert symbol Read operator’s 

manual

Safety

Fire, open light

& smoking

prohibited

Hydraulic

system Brake system Oil Coolant (water) Intake air Exhaust gas Pressure

Level

indicator Liquid level Filter Temperature Failure/

Malfunction Start switch/

mechanism On/start Off/stop

Plus/increase/

positive polarity

Engage Disengage Attachment

lower Attachment

raise Spacing distance Snow thrower,

collector auger Minus/decrease/

negative polarity

Horn Battery charging

condition

Hourmeter/elapsed

operating hours Fast Slow Continuous

variable, linear Volume empty Volume full

Machine travel

direction,

forward/rearward

Control lever

operating

direction, dual

direction

Control lever

operating

direction, multiple

direction

Clockwise

rotation Counter-clock-

wise rotation Grease

lubrication

point

Oil lubrication

point Lift point

Jack or

support point Draining/

emptying Engine lubricat-

ing oil Engine lubricating

oil pressure Engine lubricating

oil level Engine lubricating

oil filter Engine

lubricating oil

temperature

Engine coolant

Flush with water Engine Transmission

Hearing

protection must

be worn

Caution, toxic

risk

Eye protection

must be worn Head protection

must be worn First aid

Safety

Transmission

failure/malfunction Clutch Neutral High Low Forward Reverse Park

NHLFRP

First gear Second gear

Third gear (other #'s

may be used until

the maximum # of for-

ward gears is reached.)

Hydraulic oil Hydraulic oil

temperature

231

Hydraulic oil

pressure Hydraulic oil level Hydraulic oil filter

Hydraulic oil

failure/malfunction Parking brake Fuel Fuel level Fuel filter Fuel system

failure/malfunction

Diesel fuel Unleaded fuel

Headlights Lock Unlock Differential lock 4-Wheel drive Power Take-Off Power Take-Off,

rotational speed Reel cutting

element

Reel cutting

element, height

adjustment

Traction Above working

temperature range

Drilling Manual metal arc

welding Manual 0356 Water pump 0626 Keep dry

0430 weight Do not dispose

in the garbage CE logo

Engine coolant

pressure Engine coolant f

ilter Engine

lubricating oil

pressure

Engine intake/

combustion air Engine intake/

combustion air

pressure

Engine intake/

air filter Engine start Engine stop

Engine failure/

malfunction Engine rotational

speed/frequency Choke Primer (start aid) Electrical preheat

(low temperature

start aid)

Transmission oil Transmission oil

pressure

n/min

Transmission oil

temperature

Diesel Model

216 Diesel Engine: Perkins, 4-cycle, 3-cylinder, liquid

cooled, vertical overhead valve, diesel engine with cen-

trifugal water pump. 16.5 hp governed to a maximum

speed of 3200 rpm. 37.60 cu. in. displacement. Forced

lubrication gear pump. Mechanical fuel transfer pump.

Fuel filter/water separator with replaceable filter ele-

ment. Heavy-duty remote mounted air cleaner.

Radiator: Side mounted radiator, industrial construc-

tion. Cooling system capacity is 5 liters (5-1⁄4quarts).

Electrical: 12-volt starter. Interlock switches. 14-amp

alternator with remote electronic regulator rectifier.

Fuel Capacity: 24.6 liters (6.5 gallons.)

Hydraulic Oil Capacity/Filter: 8.7 liter (2.3 gallon) oil

reservoir. 12.5 liter (3.3 gallon) total system capacity.

10-micron remote mounted spin on the filter.

Ground Speed: Infinitely variable speed selection in

forward and reverse

Mowing speed: 0–8 km/h (0–5 mph)

Transport speed: 0–12.9/kmh (0–8 mph)

Reverse speed: 0–3 km/h (0–4.8 mph)

Gasoline Model

216 Gasoline Engine: Kohler, 4-cycle, air cooled, 11.9

kW (16 hp) @ 3,600 rpm, 588 cc (35.9 cu. in.) displace-

ment. Mechanical fuel pump, large capacity dual ele-

ment air cleaner, 2.5 l (5-1/4 pint) oil capacity

Steering: Adjustable steering wheel. Pinion gear and

sector gear with solid drag link to the rear steer wheel

arm.

Fuel Capacity: 22.7 liters (6.0 gallons.)

Electrical: 12-volt starter. Interlock switches. 15-amp

alternator with remote electronic regulator rectifier.

Ground Speed: Infinitely variable speed selection in

forward and reverse

Mowing speed: 0–8 km/h (0–5 mph)

Transport speed: 0–10.5 kmh (0–6.5 mph)

Reverse speed: 0–4.8 km/h (0–3 mph)

Both Models

Traction Drive: Hydrostatic drive; variable displace-

ment pump, infinitely variable in both forward and

reverse direction. High-torque hydraulic wheel motors.

Brakes: Service braking through the dynamic character-

istics of the hydrostat. Parking or emergency brake is

actuated by a ratchet hand lever.

Tires/Wheels: Two front traction tires, 18 x 8.50-8,

tubeless, 4-ply rating. Rear steering tire 18 x 6.50-8, 4-

ply tire with tube. Recommended tire pressure 97–138

kPa (12–16 psi).

Frame: The frame consists of formed steel, welded steel

and steel tubing components.

Model 03420: Tricycle vehicle with 2-wheel traction

drive in front and rear wheel steering.

Model 03425: Tricycle vehicle with 3-wheel traction

drive and rear wheel steering.

Model 03410: Tricycle vehicle with 2-wheel traction

drive in front and rear wheel steering.

Model 03430: Tricycle vehicle with 3-wheel traction

drive and rear wheel steering.

Cutting Unit Lift: Hydraulic lift with an automatic reel

shut off.

Overall Dimensions:

Wheel tread width: 137.2 cm (54 in.)

Wheel base: 139.7 cm (55 in.)

Width: 205.7 cm (81 in.)

Length: 233.7 cm (92 in.)

Height: 109.2 cm (43 in.)

Weight with 5-blade cutting unit:

Model 03420: 449.8 kg (1,205 lb.)

Model 03425: 461 kg (1,235 lb.)

Weight with 8-blade cutting unit:

Models 03410, 03430: 467 kg (1,250 lb.)

Specifications

CHECKTHE CRANKCASE OIL

The engine is shipped with oil in the crankcase; howev-

er, you must check the oil level before and after you first

start the engine.

1. Position the machine on a level surface.

2. Remove the dipstick and wipe it with a clean rag.

Push the dipstick down into the dipstick tube and

make sure it is seated fully. Pull out the dipstick

and check the oil level. If the level is low, add

enough oil to raise the level to the FULL mark on

the dipstick.

A. Above 0° C—Use SAE 30.

B. Below 0° C—Use SAE 5@-20 or 5W30.

IMPORTANT Check the oil level every 5 operat-

ing hours or daily. Change the oil after every 50

hours of operation.

FILLTHE FUELTANK

Diesel Model:

The engine runs on No. 2 diesel fuel. Fuel tank capacity

is 24.6 liters (6.5 gallons).

1. Clean the area around the fuel tank cap.

2. Remove the fuel tank cap.

3. Fill the tank to about 2.5 cm (one inch) below the

top of the tank (bottom of the filler neck). DO

NOT OVERFILL. Then install the cap.

4. To prevent a fire hazard, wipe up any fuel that may

have spilled .

Figure 1 Diesel Model

1. Dipstick

Figure 2 Gasoline Model

1. Oil fill cap

Figure 3

1. Oil fill cap

Before Operating

Before servicing or making adjustments to the

machine, stop the engine and remove the key

from the switch.

CAUTION

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Toro Tondeuse à gazon

Toro

Toro 39984 Manuel utilisateur

Toro

Toro Reelmaster 7000-D Manuel utilisateur

Toro

Toro e-cycler 20360 Manuel utilisateur

Toro

Toro TITAN HD 2000 Series Manuel utilisateur

Toro

Toro 74182 Manuel utilisateur

Toro

Toro 71242 Wheel Horse 16-38HXLE Manuel utilisateur

Toro

Toro 73552-9900001 Manuel utilisateur

Toro

Toro GrandStand 72504TE Manuel utilisateur

Toro

Toro groundsmaster 455-D Manuel utilisateur

Toro

Toro Z453 Z Master 74416TE Manuel utilisateur

Toro

Toro Recycler 20332 Manuel utilisateur

Toro

Toro Groundsmaster 4010 Manuel utilisateur

Toro

Toro 30696 Manuel utilisateur

Toro

Toro 30551 Manuel utilisateur

Toro

Toro 74943 Manuel utilisateur

Toro

Toro 02000 GROUNDS PRO 2000 Manuel utilisateur

Toro

Toro Recycler 21463 Manuel utilisateur

Toro

Toro 20814 Manuel utilisateur

Toro

Toro Carefree 21040 Manuel utilisateur

Toro

Toro Groundsmaster 4100 Manuel utilisateur

Toro

Toro ProLine 22031 Manuel utilisateur

Toro

Toro 2000 Series Manuel utilisateur

Toro

Toro 22291 Manuel utilisateur

Toro

Toro 30291TE Manuel utilisateur

Manuels Tondeuse à gazon populaires d'autres marques

RHINO

RHINO 1958 Manuel utilisateur

Wolf Garten

Wolf Garten Compact plus 40 B Manuel utilisateur

Cub Cadet

Cub Cadet LTX 1045 Manuel utilisateur

Craftsman

Craftsman 917.378461 Manuel utilisateur

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Manuel utilisateur

Challenge

Challenge CH18V2 Instructions de fonctionnement

TALEN TOOLS

TALEN TOOLS AVR HGM30 Manuel utilisateur

DEWEZE

DEWEZE ATM-725 Manuel d'utilisation

Weed Eater

Weed Eater 180083 Manuel utilisateur

Husqvarna

Husqvarna Poulan Pro PP185A42 Manuel utilisateur

Better Outdoor Products

Better Outdoor Products Quick Series Manuel utilisateur

Cub Cadet

Cub Cadet 23HP Z-Force 60 Manuel d'utilisation

MTD

MTD 795, 792, 791, 790 Manuel utilisateur

Dennis

Dennis FT 610 Manuel utilisateur

AIRFORCE

AIRFORCE F-15 Gen 3 Manuel utilisateur

MTD

MTD 126-220-000 Manuel utilisateur

Stihl

Stihl RMA 443 PV Manuel utilisateur

Yard-Man

Yard-Man 3700-0 Manuel utilisateur