TNA TX7930 Manuel utilisateur

TX7930

Handheld Programmer

Installationand OperationManual

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

Product Safety

To prevent severe injury and loss of life or property, read the instruction carefully before using the

handheld programmer ensure proper and safe operation of the system.

European Union directive

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed

of as unsorted municipal waste in the European Union. For proper recycling, return

this product to your local supplier upon the purchase of equivalent new

equipment, ordispose ofit at designated collection points.

For more information please visit the website at www.recyclethis.info

Disclaimer

The information in this manual is furnished for informational use only and subject to the change

without notice. While every effort has been made to ensure that the information contained in this

user manual is accurate, reliable and up to date. The TANDA Technology cannot be held

responsible for inaccuracies or error that may appear in this manual.

Document Improvement

There is always room for improvement, your comment will help us the quality of this manual. Do not

hesitate to send report any error, inaccuracy or improvement request on this user document by

email to info@tandauk.com

General Precautions

Do not use the TX7930 handheld programmer in any way or for any purpose not described in this

manual.

Do not put any foreign objects into jack socket orbatter compartment.

Do not clean the programmer with alcohol or any organic solvent.

Do not place the programmer in direct sunlight or rain, near heater or hot appliances, any location

exposed to extremely high or low temperatures, high humidity, or dustylocations.

Do not expose the batteries to heat or flame. Keep the batteries out of reach of children, they are

choking hazards and very dangerous if swallowed.

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

Table of Content

1 Introduction....................................................................................................................................... 4

1.1 Overview..................................................................................................................................... 4

1.2 Feature andBenefits................................................................................................................. 4

1.3 Technical Specification............................................................................................................. 4

1.4 Names and Location................................................................................................................. 5

2 Operation.......................................................................................................................................... 5

2.1 Installing of Batteries.................................................................................................................. 5

2.2 Connecting to the Device........................................................................................................ 6

3 Programming..................................................................................................................................... 8

3.1 To Read ....................................................................................................................................... 8

3.2 To Write........................................................................................................................................ 8

3.3 To R/W Config............................................................................................................................. 9

3.4 Set............................................................................................................................................... 10

4 Troubleshooting Guide.................................................................................................................. 10

5 Returns andWarranty Policy......................................................................................................... 11

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

1 Introduction

1.1 Overview

The TX7930 is the general purpose programming tool use for TX7000 family products. This unit is

designed to suit for entering device parameters such as address, sensitivity, mode and types to meet

the site situation and environmental requirements. In addition, the programmer is capable to read

the previous encoded parameters to use for testing application and troubleshooting purposes.

The TX7930 is miniature and robust design makes it convenient to bring in the work place. The

programmer is packed with twin 1.5V AA battery and cable, ready for usage once received. Easy to

understand the display and with functional keys allow easy single-button activation of the common

used parameters.

1.2 Feature and Benefits

•Write, read and erase device parameters

•Pluggable cable withendalligator clip to hold tight the terminals

•LCD displayand functional keys

•Low current consumption for longer battery lifespan

•Circuit protection against clip

•Auto power-off within 5 minutes

1.3 Technical Specification

•Battery Required 2X1.5 AA / Included

•Current Consumption Standby 0μA, In-use: 3mA

•Protocol T&A

•Material / Colour ABS / Grey Glossy finishing

•Dimension / LWH 130 mm x 54 mm x28 mm

•Humidity 0 to 95% RelativeHumidity, Noncondensing

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

1.4 Names and Location

①Data Display 16 Characters, four-segment display shows the device address, set types

and mode and ID value

②Function Key Allow easy single-button activation of the common used parameters such

as exit, clear, page, read and write function

③Numerical Key 0 to 9 keys used to enter numeric values

④Jack Socket Locationfor male connector of programming cable

⑤Loop Terminal Connection to signaling loop used for testing the loopwiring

⑥Label Programmer details and specification

⑦Battery Compartment Location for programmer batteries

2 Operation

This programmer must be operated and maintained by a qualified or factory trained service

personnel. Check the package contains before using your programmer.

Package contains the following:

1. TX7930 Programmer

2. Twin 1.5 AA Battery

3. Programming cable

4. Strap belt

5. User guide.

2.1 Installing of Batteries

This programmer has been designed to allow changing the battery quicklyand easily.

1. Remove the battery compartment cover and insert the two AA batteries.

2. Make sure the positive and negatives ends are facing the correct directions.

3. Close the battery cover and press down until it clicksinto place.

Warning: Dispose the used batteries according to the local regulation.

Figure 1

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

2.2 Connecting to the Device.

The programming cable has male connector and two alligator clips at both end. This clip is used to

firmly hold the connection between the device terminal and programmer. During the programming

process if the cable is loss contact with the device, it will display Fail on the programmer. It is

recommended to be properly clipped the terminals before doing any programing. The programmer

is not sensitive to the polarity; any of those clips can connect onto the signaling terminals of each

device. Each type of device has different signaling terminal as follows:

Signaling Terminal:

Detector and Sounders

Connect the alligator clip to

terminal 1 (2) and 6 (5)

Signaling Terminal:

Manual Call Point

Connect the alligator clip to

terminal Z1 and Z2 (Marks)

Figure 2

Figure 3

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

Signaling Terminal:

Interface Modules

Connect the alligator clip to

terminal Z1 and Z2 (Marks)

Figure 4

Figure 5

Signaling Terminal:

Beam Detector

Connect the alligator clip to

terminal S1 and S2 (Marks)

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

3 Programming

Note: The Tanda device are equipped with variety of features and options that user can select or

programonsite according to the project requirement and application. This manual cannot contain

all theinformation’s for each device. We recommend referring to the specific device operation

manual for more details.

For TX7100 Intelligent Optical Smoke detector refers to Operation Manual 4050100265

For TX7110 Intelligent Heat Detector refers to Operation Manual 4050100263

For TX7120 Intelligent Optical Smoke and Heat Detector refers to Operation Manual 4050100264

For TX7130 Conventional Beam Detector refers to Operation Manual 4050100256

For TX7140 Addressable Manual Call Point refers to Operation Manual 4050100269

For TX7200 Addressable Input Module refers to Operation Manual 4050100266

For TX7210 Addressable Input/output Module refers to Operation Manual 4050100267

For TX7220 Addressable Dual Input/output Module refers to Operation Manual 4050100268

For TX7300 Addressable Sounder Strobe refers to Operation Manual 4050100270

For TX7320 Addressable Sounder refers to Operation Manual 4050100271

3.1 To Read

Selecting this feature allow user to view the device details and configurations. For example in TX7110

Intelligent Heat detector.

1. Switch-on the programmer, then press button “Read” or “1” to enter to Read mode (Figure 6).

The programmer will displaythe configurationafter few seconds. (Figure 7)

2. Press “Exit” key to go back Main Menu. Press “Power” key to switch off the programmer.

3.2 To Write

Selecting this feature allow user to write the new address number the device. For example in TX7100

Intelligent Optical Smoke detector.

1. Connect the programming cable to Z1 and Z2 terminals (Figure 2). Press “Power” to switch on

the unit.

2. Switch-on the programmer, then press button “Write” or number “2” to enter Write Address

mode (Figure 8).

3. Input the desire device address value from 1 to 254, and then press “Write” to save the new

address (Figure 9).

1. Read

2. Write T

3. R/W Config 7

4. Set

Address: 123

Category: A1R

ID: 123456789012

ReadDescription

Address:Uniquenumber

assigned

Category: Detectortype

ID: Detectorserial number

Figure 6

Figure 7

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

3.3 To R/W Config

Selecting thisfeature allow user to configure optionalfunctionsof a device such as distance,

sounder type and others. For example in TX7130 Conventional Beam Detector.

1. Switch on the programmer, then press button “3” then display “Sensitivity and Span (m)”

(Figure 10).

2. Then enter then press “0/Page” key to highlight the previous Span setting. Then press value

from 1, 2, 3 or 4 correspond to the span value and then press “Write” key(Figure 11).

Note: If display“Success”, means the entered span is confirmed. If display “Fail”, means

failure to program the span.

1. Read

2. Write T

3. R/W Config 7

4. Set

Address: 001

NextAddress:002

Success

Address: 001

Fail

Sensitivity:001

Span m:

①

8-20

②

20-40

③

40-70

④

70-100

Success

1. Read

2. Write T

3. R/W Config 7

4. Set

Figure 8

Figure 9

Figure 10

Figure 11

TX7930 Handheld Programmer

Installation& Operation Manual

4050100262-Rev1.2-1217

TANDA UK

Specifications aresubjectto changew ithout prior notice

3.4 Set

Selecting this feature allow user to set other features such as tones selection or On and OFF the

detector pulling LED as example of TX7100 Intelligent optical smoke detector.

1. Switch-on the programmer, then press button “4” to enter to Setting mode (Figure 12).

2. Input the “1” then press “Write” to change the setting (Figure 13) and LED will turn-off. To

resume the default setting, press “Clear” and then press “Write”.

3. Press “Exit” key to go back Main Menu. Press “Power” to switch off the programmer.

4 Troubleshooting Guide

What you notice What it means What to do

No display on the screen Low Battery

Loose connection with thebattery Replace the batteries

Check the internal wiring

Unable to encode data

Loss connection

Wrong connection

Damage the electronic circuit of

the device

Check the connection with the

detector

Select the appropriate signaling

terminal of the device

Check the continuity of the

programming cable

Try to other device

Parameter: 1

Success

Figure 12

Figure 13

1. Read

2. Write T

3. R/W Config 7

4. Set

Table des matières

Manuels Carte mère populaires d'autres marques

DFI

DFI SD170 Manuel utilisateur

ASROCK

ASROCK ROMED8-2T Manuel utilisateur

Asus

Asus P2L97A Manuel utilisateur

Winmate

Winmate IC70 Manuel utilisateur

Asus

Asus MES-B Manuel utilisateur

Grantech

Grantech SYS8F377VGGA-3OMN Manuel utilisateur

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuel utilisateur

Gigabyte

Gigabyte GA-9IVDT Manuel utilisateur

Texas Instruments

Texas Instruments ADS8372EVM Manuel utilisateur

Commell

Commell MS-C73 Manuel utilisateur

IBT Technologies

IBT Technologies MB860 Manuel utilisateur

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuel utilisateur

Biostar

Biostar M7VIT Bravo Instructions d'utilisation et d'installation

Intel

Intel D33217CK Manuel utilisateur

Asus

Asus F1A55-M LX PLUS R2.0 Manuel utilisateur

EPC

EPC EPC9147C Manuel utilisateur

Asus

Asus EX-B760M-V5 D4 Manuel utilisateur

EPOX

EPOX MU-8KHA0010 Manuel utilisateur