TMS LC-18-4CH-A1 Manuel utilisateur

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

________________________________________________________

LC-18-4CH-A1

Lighting Controller Unit

USER MANUAL

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Table of Contents

Hardware ................................................................................................................................................2

Packing List..........................................................................................................................................2

General Description ................................................................................................................................3

Specification........................................................................................................................................3

Connectors Description...........................................................................................................................4

Operation Mode .....................................................................................................................................7

Constant Mode ...................................................................................................................................7

Strobe Mode .......................................................................................................................................7

Trigger Mode.......................................................................................................................................8

Current Multiplier ...................................................................................................................................8

LC-18 Software........................................................................................................................................9

Change IP Address.................................................................................................................................11

Slave Board Address Setting .................................................................................................................12

Communication Connection .............................................................................................................13

Input Signal ...........................................................................................................................................14

Output Signal ........................................................................................................................................14

Accessories............................................................................................................................................15

24V Power Supply.............................................................................................................................15

Cable Selection..................................................................................................................................16

Cable Information .................................................................................................................................17

Power Cord Information .......................................................................................................................18

Drawing Dimension...............................................................................................................................19

Communication Protocol......................................................................................................................20

Revision Notes

Rev

Date/Author

Comment

1.0

July2020/KW

First Revision

1.1

Aug2020/KW

Added Communication Protocol Documentation

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Hardware

Packing List

Please ensure the following items are in the package:

LC-18-4CH-A1 Controller Package

LC-18-4CH-A1

Ethernet Cable x1

RS232 Cable x1

Communication Cable x1set

24V Power Supply (Optional)

Lighting Cable x 16pcs (Optional)

User Manual x1

User Interface (download from the link below)

Link for user interface and user manual from TMS LITE website:

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

General Description

The LC-18-4CH-A1 controller provides intensity control of LED lightings for machine vision

applications. The controller consists of 16 channels with individual settings for each channel.

There are 3 modes of operation provided to support different types of application.

Specification

Parameter

Value

Controller Supply Voltage

24 VDC

Lighting Supply Voltage

5/12/24/48 VDC

(According to Lighting Voltage Rating)

No. of Channel

Channel Mode

Constant, Strobe, Trigger

Output Current

Maximum 1A per channel

Strobe Delay, Strobe Width,

Output Delay, Output Width

Adjustable 0 –99.99ms (10us/step)

Input Trigger Signal

3.3-24V, >5mA

rising/falling edge trigger

Output Trigger Signal

Support rising/falling edge output trigger

Trigger Delay

≤ 20us

Software Control

RS232 / TCPIP

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Connectors Description

Terminal

Function

VS (24V)

Controller Power Supply +

GND

Controller Power Supply –

COMM

Communication Port (between master and slave boards)

RS232

RS232 Communication

TCPIP

TCPIP Communication

ADDR

4 Way DIP Switch (for slave address selection)

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Terminal

Function

LIGHT INPUT +

Power Supply for Lighting +

LIGHT INPUT –

Power Supply for Lighting –

CH +

Lighting Channel Output +

CH –

Lighting Channel Output –

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Terminal

Function

IN +

External Input +

IN –

External Input –

OUT +

External Output +

OUT –

External Output –

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Operation Mode

Constant Mode

Constant mode offers continuous lighting intensity control. Lighting intensity is controlled

using constant current technique. Brightness can be adjusted from fully off to fully on in the

range of 0 –255.

Strobe Mode

Strobe mode provides short interval triggering for applications that require high intensity and

high precision. An input trigger signal will turn on the lighting output based on pre-set delay

and duration parameters.

There are 4 adjustable strobe parameters available:

Strobe Delay = Delay time between the external input signal and the lighting output

Strobe Width = Duration of the lighting’s turn on time

Output Delay = Delay time between the external input signal and the external output signal

Output Width = Duration of the external output signal’s turn on time

Parameter timings are in the range of 0-9999 which is equivalent to 0-99.99ms (in step of 10us)

External Trigger

Lighting Strobe

Camera Output

Strobe Delay

Strobe Width

Output Delay

Output Width

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

Trigger Mode

Trigger mode provides most flexibility for variable timing light output. The light output ON

when input trigger signal received and OFF when no input signal.

Current Multiplier

Current Multiplier setting provides more precise control of lighting intensity for lightings with

different current ratings.

Current Multiplier setting range = 1-10

1 = 10% of max output current (100mA)

2 = 20% of max output current (200mA)

3 = 30% of max output current (300mA)

4 = 40% of max output current (400mA)

5 = 50% of max output current (500mA)

6 = 60% of max output current (600mA)

7 = 70% of max output current (700mA)

8 = 80% of max output current (800mA)

9 = 90% of max output current (900mA)

10 = 100% of max output current (1000mA/1A)

For example: if the lighting’s current rating is 260mA, current multiplier can be set to 3, setting

the maximum output current to 300mA. So the lighting’s intensity can be adjusted from low to

high within the range of 0-255.

If multiplier is set too high, for example 10 (100% of max output = 1A), theadjustable intensity

range for the lighting is only about 0-67. Setting the intensity value to 68 or higher will not

have any effect towards the lighting output brightness.

External Trigger

Lighting Strobe

TMS Lite LC-18-4CH-A1 LIGHTING CONTROLLER UNIT

LC-18 Software

The controller can be controlled using LC-18 software. Connect the controller to computer

with RS232 cable and TCPIP cable.

1. Software Connection :

a. Select COMPORT or TCPIP to connect.

b. Disconnect the software

2. Read and Save function for all slave board :

a. Read all slave board’s parameter from controller.

b. Save all slave board’s parameter into EEPROM.

3. Strobe function for all channel :

a. Strobe all channel once.

b. Repeat strobe all channel (together).

c. Repeat strobe channel by channel.

4. Reset all channel’s parameter to default value.

5. Master board firmware version.

6. Each tab display all the parameters for each slave board.

Table des matières

Autres manuels TMS Unité de contrôle

TMS

TMS LC-18-4CH-A1-RGBW Manuel utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur