TiSUN MULTIPLEX Manuel utilisateur

MULTIPLEX

Advanced

TiSUN GmbH | Stockach 100 | A-6306 Söll | Tel.: +43 (0) 53 33 / 201 - 0 | Fax: +43 (0) 53 33 / 201 100

E-Mail: [email protected] | www.tisun.com | FN 52724 k Landesgericht Innsbruck | UID-Nr.:ATU32041304

EN ISO 9001 :2000

Zertificat Nr. 20 100 72002241

www.tuv.at

USER GUIDE GB

MULTIPLEX 4-18

 F

MULTIPLEX 19- 33

BEDIENUNGSANLEITUNG D

MULTIPLEX 34 - 48

 IT

MULTIPLEX 49 - 63

MANUAL DEL USUARIO ES

MULTIPLEX 64 - 78

MANUAL DE INSTALAÇÃO E UTILIZAÇÃO PT

MULTIPLEX 79 - 93

GEBRUIKERSHANDLEIDING NL

MULTIPLEX 94108

HASZNÁLATI ÚTMUTATÓ HU

MULTIPLEX 109-123

 SLO

MULTIPLEX 124-138

 RU

MULTIPLEX 139-153

  GR

MULTIPLEX 154- 168

MULTIPLEX ADVANCED - extension module

Installation and Operation Manual

IMPORTANT!

Before starting work the installer should carefully read this Installation & Operation Manual, and make

sure all instructions contained there in are understood and observed.

The Solar controller should be mounted, operated and maintained by specially trained personnel

only. Personnel in the course of training are only allowed to handle the product under the supervision

of an experienced fitter. Subject to observation of the above terms, the manufacture shall assume the

liability for the equipment as provided by legal stipulations.

All instructions in this Installation & Operation manual should be observed when working with the

controller. Any other application shall not comply with the regulations. The manufacturer shall not be

liable in case of incompetent use of the controls. Any modifications and amendments are not allowed

for safety reasons. The Solar controller maintenance may be performed by service shops approved

by the manufacturer only.

The functionality of the controller depends on the model and equipment. This installation leaflet is

part of the product and has to be maintained.

APPLICATION

The Solar controller is developed for Solar heating systems. The temperature of the water in the tank



The controller is normally used in conjunction with a hydraulic control unit which includes a circulation

pump, Safety valve.

The controllers have been designed for use in dry environments, e.g. in residential rooms, office

spaces and industrial facilities.

Verify that the installation complies with local regulations before operation.

SAFETY INSTRUCTIONS

Before starting work disconnect power supply!

All installation and wiring work related to the controller must be carried out only when de-energized.

The appliance should be connected and commissioned by qualified personnel only. Make sure to

adhere to valid safety regulations.

The controllers are neither splash- nor drip-proof. Therefore, they must be mounted at a dry place.

Do not interchange the connections of the sensors and the 230V connections under any

circumstances! Interchanging these connections may result in life endangering electrical hazards or

the destruction of the appliance and the connected sensors and other appliances.

Table of content

1Presentation and description...........................................................................................6

1.1 Product description..........................................................................................................6

1.2 Technical characteristics .................................................................................................6

1.3 Connections.....................................................................................................................7

2Multiplex Menu ................................................................................................................8

3Multiplex standard systems .............................................................................................9

4Function Blocks.............................................................................................................10

4.1 Presentation ..................................................................................................................10

4.2 "Thermostat" functional block........................................................................................11

4.3 "PHE" primary plate heat exchanger functional block....................................................11

4.4 "Difference control unit" functional block........................................................................13

4.5 "Timer" functional block.................................................................................................14

5Tank Priority ..................................................................................................................15

5.1 Systems with two tanks (Systems 2, 3, 9, 10, 13 and 17) .............................................15

5.2 Systems with three tanks (Systems 11, 14, 15 and 18).................................................15

5.3 Systems with four tanks (Systems 12 and 16)...............................................................16

6HEATING CIRCUIT 1 / 2...............................................................................................17

1 Presentation and description

1.1 Product description

Expansion module (only in conjunction with the Duplex Basic double-loop solar control unit)

For multiple-loop solar and heating systems

Large display with backlight for graphical indication of schematic, operating status, temperatures output and energy yield. Simple,

menu-based operation with 4 keys

18 standard systems for 1 to 4 tanks and 1 or 2 collector arrays, systems with plate heat

exchanger also selectable

Selectable functional blocks can be connected to the outputs (difference, thermostat, plate heat exchanger and timer), especially to

control individual solar and heating systems and additional functions

Two weather-compensating heating circuits with remote control, domestic hot water priority circuit and auto summer mode

16 inputs and 10 outputs

4 outputs (Triac), with either phase control for electronic speed control of standard solar and heating pump or with PWM signal for

speed controlled high-efficiency energy-saving pumps.

6 outputs (relays) for standard solar and heating pumps

2 inputs for VFS flow sensors for measuring flow rate and temperature and for system control, as well as energy balancing (no

wearing parts).

2 inputs for RPS pressure sensors and for system control

Integrated, permanent storage of operating data, with graphical indication on display.

SD memory card slot: permanent, long-term recording for data logging of system parameters and operating data (temperatures,

pump status, operating time, output and energy yield). Detailed evaluation on a PC (system monitoring, system configuration, energy

yield for energy balancing).

Order SD card and software separately SD Data log kit 1510327

Protective functions (overheating protection for collector and system, frost protection, pump exercise function)

Sensor auto check and alarm.

Energy saving mode (automatic display standby mode after 15 mins.)

1.2 Technical characteristics

Designation

Multiplex Advanced multiple-loop solar and heating control unit

Type

VPM Multiplex

Item no.

1510319

Housing

Plastic anthracite

Operating temperature

0-50 °C

Protection class

IP 42

Electrical connection

230 VAC / 50 Hz

Total connected load Duplex

4.7 A / 230 VAC

Total connected load Multiplex

5.8 A / 230 VAC

Duplex fuse

Pico fuse 5 A/250 V (5 x 20 mm)

Multiplex fuse

Pico fuse 6.3 A/250 V (5 x 20 mm)

Dimensions Duplex

160 x 86 x 53

Dimensions Multiplex

375 x 90 x 56

Mounting Duplex

Wall mounting or installation in the TiSUN solar stations up to 50 m2

Mounting Multiplex

Wall mounting or installation in a distribution panel or protective casing

Menu languages

8 languages

Operating modes

Automatic, off or manual with test menu

Sensors

Pt 1000

Sensor monitoring

Automatic sensor testing (short-circuit and open-circuit) with fault display

Protective functions

Overheating protection for collector and system, recooling, frost protection, pump exercise

function

Multi-tank systems

Tank priority circuit

1.3 Connections

Inputs T1

Collector sensor

Inputs T2, T3, T4, T7 bis T12

Sensor for tank, collector or additional functions

Input T5

Sensor for collector return (theoretical heat quantity metering), tank, collector or additional functions

Input T6

Pulse flow meter (heat quantity meter), pulse 5 VDC

VFS input (Duplex)

VFS flow and temperature sensor for computing output and energy (electronic heat quantity meter),

input voltage 5 VDC, flow output voltage 0.5 to 3.5 VDC, temperature output voltage 0.5 to 3.5 VDC,

flow measuring range 1 to 200 l/min

VFS input (Multiplex)

2 inputs for VFS flow and temperature sensor for system control (not for calculating output and

energy), input voltage 5 VDC, flow output voltage 0.5 to 3.5 VDC, temperature output voltage 0.5 to

3.5 VDC, flow measuring range 1 to 200 l/min

RPS input

2 inputs for RPS pressure and temperature sensor (system control), input voltage 5 VDC, pressure

output voltage 0.5 to 3.5 VDC, temperature output voltage 0.5 to 3.5 VDC, pressure measuring range

0 to 10 bar

Outputs P1, P2, P4 and P5

TRIAC output 230 V / max. 1 A, for solar and heating pumps, with speed control (modulated

phase control) Min. 2W load on TRIAC to switch, if a power relay or similar is used.

PWM signal 4-15 V / 100-4,000 Hz, for control and speed regulation of high efficiency pumps

Note: It is also possible to connect a valve to these outputs in conjunction with the resistance kit.

Outputs P3, P6, P7, P8, P10

Relay output 230 V / max. 2 A, for solar and heating pump or valve

Output P9

Floating relay output 230 V/max. 2 A, for solar and heating pump, valve or floating demands

RJ45 slot

Duplex-Multiplex digital interface

*ATTENTION: As a savety feature, all critical parameters (system and Extra function) are not accessible any more after 4 hours

power on. If you want to modify these parameters, you must unplug and plug in controller. No settings are lost when unplugging, or

after a power failure.After 4 hours it is only possible to alter system optimization settings.

2 Multiplex Menu

(These extensions of the menus are only available when the extension module MULTIPLEX is linked on the DUPLEX controller)

Where

Parameters

Possibility

Factory

Setting

With

DUPLEX Setting menu

MULTIPLEX Setting menu

Maximum temperature

tank 1/2

15-95°C

65°C

All systems

dTMax tank 1/2

4-40°C

15°C

All systems

dTMin tank1/2

2-35°C

7°C

All systems

Min speed P. (Triac)

30-100%

60%

P1,P2,P4,P5 (if speed controlled)

dT FS

5-50°C

35°C

P1,P2,P4,P5 (if speed controlled)

Min. collector

temperature

1 - 99°C

25°C

All systems

Max. collector

temperature

110 –150 °C

120°C

Heat protection (system protection)

GDS 1

RPS 0-4 or 0-6 or 0-10 bar

VFS 1-12, 2-40, 5-100, 10-200, 20-400

l/min

Not

connected

Grundfoss Flow sensor (VFS) or Pressure

sensor (RPS)

GDS 2

RPS 0-4 or 0-6 or 0-10 bar

VFS 1-12, 2-40, 5-100, 10-200, 20-400

l/min

Not

connected

Grundfoss Flow sensor (VFS) or Pressure

sensor (RPS)

T1 to T5 and T7 to 12

Not

connected

Optionnal PT1000 temperature sensor for

energy calculation

Maximum temperature

tank 3/4

15-95°C

65°C

3/4 tank system

dTMax tank 3/4

4-40°C

15°C

3/4 tank system

dTMin tank3/4

2-35°C

7°C

3/4 tank system

Heating circuit 1/2

Yes/No

Heating circuit 1/2

GDS 3/4

RPS 0-4 or 0-6 or 0-10 bar

VFS 1-12, 2-40, 5-100, 10-200, 20-400

l/min

VFS Energy calculation see DUPLEX



Not

connected

Grundfoss Flow sensor (VFS) or Pressure

sensor (RPS)

Temp Sensor 2

T1 to T5 and T7 to 12

Not

connected

Optionnal PT1000 temperature sensor for

energy calculation

Multiplex Output

Relay 2 to 8

Schematic/off/thermostat/

difference control unit/plate

heat exchanger/timer

Off

Schematic or functional blocks

Relay 9

Schematic/off/thermostat/

difference control unit/plate

heat exchanger/timer

Off

Schematic or functional blocks (floating)

Relay 10

scheme/off/thermostat

Off

Schematic or functional block

 Multiplex Out -

P2

Relay 4

Relay 5

Relay 6

Relay 7

 Informations -

Services

Settings

Operation

Operation h

Temperatures

Multiplex Out

New Submenu:



New Fonction in Submenu:

Settings

See part 4

Function Blocks

3 Multiplex standard systems

System 1

Duplex

System 2

Duplex

System 3

Duplex

System 4

Duplex

P1= Dt(T1,T2)

P1= Dt(T1,T2orT4)

P2= Dt(T1,T4)

P1= Dt(T1,T2) P2= Dt(T1,T4)

P1= Dt(T1orT4,T2) P2= Dt(T4,T2)

System 5

Duplex

System 6

Duplex

System 7

Duplex

System 8

Duplex

P1 = Dt(T1,T2) P2 = Dt(T4,T2)

P1= Dt(T1,T2) P2= Dt(T3,T4)

P1 = Dt(T1,T2) P2 = Delay P1

P1 = Dt(T1,T2) P2 = Dt(T4,T2)

System 9

Multiplex

System 10

Multiplex

System 11

Multiplex

System 12

Multiplex

P1= Dt(T1,T2 or T3)

P2= Dt(T4,T2orT3)

P7= Dt(T1 or T4,T3)

P1= Dt(T1,T2 or T3)

P2= Dt(T1,T2)

P5= Dt(T1,T3)

P1= Dt(T1,T2orT3orT7)

P2= Dt(T1,T2)

P5= Dt(T1,T3) P7= Dt(T1,T7)

P1= Dt(T1,T2orT3orT7orT8)

P2= Dt(T1,T2) P5= Dt(T1,T3)

P7= Dt(T1,T7) P8= Dt(T1,T8)

System 13

Multiplex

System 14

Multiplex

System 15

Multiplex

System 16

Multiplex

P1= Dt(T1orT4,T2)

P2= Dt(T1orT4,T3)

P7= Dt(T1,T2orT3)

P8= Dt(T4,T2orT3)

P1= Dt(T1orT4,T2)

P2= Dt(T1orT4,T3)

P5= Dt(T1orT4,T7)

P7= Dt (T1,T2orT3orT7)

P8= Dt(T4,T2orT3orT7)

P1= Dt(T1,T2)

P2= Dt(T1,T3)

P5= Dt(T1,T7)

P1= Dt(T1,T2) P2= Dt(T1,T3)

P5= Dt(T1,T7) P4= Dt(T1,T8)

Functional blocks:

(for individual connection to

outputs)

- Schematic

- Primary plate heat exchanger

- Secondary plate heat exchanger

- Thermostat function

(with 3x timer)

- Difference control unit

(with 3x timer)

- Timer block

Heating circuit control unit:

-Two availables

weather-compensating heating circuits

with

- Remote control for living areas

- Ambient temperature sensor

- Domestic hot water priority circuit

- Day/Night setback

- Auto summer mode

- ECO Mode

System 17

Multiplex

System 18

Multiplex

P1= Dt(T1,T2orT3)

P2= Dt(T4,T2orT3)

P7= Dt(T1 orT4,T2)

P8= Dt(T1 orT4,T3)

P7= Dt(T1 orT4,T2)

P8= Dt(T1 orT4,T3)

P5= Dt(T1orT4,T7)

P1=T1 P2=T4

4 Function Blocks

4.1 Presentation

* Speed controls description, standard and High Efficiency Pump

Optimised flow control and temperature difference between flow and return with variable pump speed via infinitely adjustable Triac

phase control or PWM signal for high efficiency pumps (energy saving pumps).

Triac Speed Control PWM speed control

Tank1

T2 (°C)

dtMin

dt Fs

Collector

T1 (°C)

Maxtemp

Tank1

dt Fs

dT = T1 T2

100%

dtMax

Control

dtMax

85%

OFF

100%

Control

100%

OFF

NB: Speed is regulated by a Triac modulated phase

control; therefore please check before modifying

values and commissioning:

Whether the pump can be operated using a

modulated phase controlled speed control.

That the minimum speed of the pump is equal

to or lowers than the regulated minimum

speed.

That the pump step switch is set to the

maximum output.

dTMin

dTMax

100%

Pump startup

dTFs

Controlled

Speed range

Pump startup

dTMin

dTMax

100%

Min rev pump

dTFs

Controlled

Speed range

30%

Multiplex Output

Speed Control

P2, P4, P5

No SC = OFF

PhAC SC = ON

(Standard pump)

PWM SC = ON

(Hight efficiency pump)

Outputs

P2, P3, P4, P5, P6, P7, P8, P9

Output

P10

OFF

Scheme

Thermostat function

DiffControl Function

PHE

(Plate Heat Exchanger)

Timer

OFF

Scheme

Thermostat function

Heating Circuit 1

P4, P6, P10

Heating Circuit 2

P5, P7, P8

P3 Backup heater

(D.H.W tank)

P9 Backup heater

(Heating storage)

Table des matières

Langues :

Autres manuels TiSUN Unité de contrôle

TiSUN

TiSUN FM-S Guide de l'utilisateur

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur