Tiso Gate-GS Manuel utilisateur

“TiSO-PRODUCTION” LTD

WAIST-HIGH TURNSTILE

SERVO-OPERATED SWING GATE

Gate-GS

Gate-GSH

Gate-TS

Gate-TTS

OPERATION MANUAL

AUIA.203 OM (rev.1.2.2)

UKRAINE

2023

Operation Manual 2 
CONTENTS 
 
INTRODUCTION.........................................................................................................................................................3 
1. DESCRIPTION AND OPERATION ...............................................................................................................5 
1.1 General Information and Purpose...................................................................................................................5 
1.2 Specifications.................................................................................................................................................7 
1.3 Configuration and Scope of Delivery .............................................................................................................7 
1.4 Design and operation......................................................................................................................................9 
1.5 Instrumentation, tools and accessories..........................................................................................................11 
1.6 Description and operation of controllers as a component of the turnstile.....................................................11 
2 INTENDED USE .....................................................................................................................................................14 
2.1 Operation restrictions....................................................................................................................................14 
2.2 Layout and installation..................................................................................................................................15 
2.3 Preparation for use........................................................................................................................................20 
2.4 Contingency actions......................................................................................................................................22 
3 MAINTENANCE.....................................................................................................................................................22 
3.1 General guidelines ........................................................................................................................................22 
3.2 Safety Measures............................................................................................................................................23 
3.3 Maintenance procedure.................................................................................................................................23 
4 ROUTINE MAINTENANCE ..................................................................................................................................24 
4.1 General guidelines ........................................................................................................................................24 
4.2 Possible malfunctions ...................................................................................................................................24 
4.3 Postrepair checkout......................................................................................................................................24 
5 TRANSPORTATION AND STORAGE .................................................................................................................24 
5.1 Turnstile storage ...........................................................................................................................................24 
5.2 Turnstile transportation.................................................................................................................................24 
6 DISPOSAL...............................................................................................................................................................25 
Annex А.1(mandatory) Overall and installation dimensions of “Gate-GS” type turnstile.........................................26 
Annex А.2(mandatory) Overall and installation dimensions of “Gate-GSH”type turnstile......................................27 
Annex А.3(mandatory) Overall and installation dimensions of  “Gate-TS”type turnstile .........................................28 
Annex А.4(mandatory) Overall and installation dimensions of “Gate-TTS” type turnstile.......................................29 
Annex B (mandatory) Control desk and connection diagram .....................................................................................30 
Annex C (mandatory) Wiring diagram of Swing Gate type turnstile..........................................................................32 
Annex D.1(mandatory) Wiring diagram of turnstile connection to access control system (ACS)..............................33 
Annex D.2(mandatory) Wiring diagram of one turnstile connection to fire alarm system (FAS)...............................34 
Annex D.3(mandatory) Wiring diagram of two turnstiles connection to fire alarm system (FAS).............................35 
Annex D.4(mandatory) Wiring diagram of two turnstiles connection to fire alarm system (FAS).............................36 
Annex D.5(mandatory) Wiring diagram of turnstile connection to control panel.......................................................37 
 
 
 
 
 

Operation Manual 3

INTRODUCTION

This Operation Manual (hereinafter referred to as OM) covers the servo-operated waist-high

turnstile of swing gate type (hereinafter referred to as the "turnstile"). The Operation Manual

contains information about design, specifications, installation for proper operation and

maintenance of the turnstile.

This Operation Manual is prepared in compliance with the specification requirements of ТU

U 28.9-32421280-005:2018.

The turnstile shall be serviced only by the qualified staff having the relevant class of permit

to work with electrical facilities with voltage up to 1000V and scrutinizing this Operation Manual,

obtaining safety instructions and trained for operation and maintenance of the turnstile.

Reliability and durability of the turnstile operation is provided with observation of modes

and conditions of transportation, storage, installation and operation. So, fulfillment of all

requirements specified in this document is mandatory.

Due to regular improvement of the product its design can be modified without degradation

of the product features and quality not covered by this Operation Manual.

Depending on the purpose and design features of the turnstile, the following pattern of

reference designation is accepted:

T3.КХХ.X D

Waist-high turnstile

Swing Gate

with leaf rotation

to both sides

Servo-operated,

with stainless

steel leaf

СН

Painted housing

Polished stainless steel

Servo-operated,

with glass

leaf

СС

Brushed stainless steel

Example of reference designation of the servo-operated waist-high turnstile of swing gate

type made of brushed stainless steel when the turnstile T3.КСС.PD TU U 28.9-32421280-

005:2018 is ordered.

Operation Manual 4

WARNINGS TO THE CUSTOMER

ON SAFE OPERATION OF THE TURNSTILE

These warnings are designed for ensuring of safety during operation of the turnstile to prevent

violation of safety characteristics by improper installation or operation. These warnings are aimed at

drawing attention of the customer to safety problems

GENERAL WARNINGS

The Operation Manual is an integral part of the product and it shall be handed over to the

customer. The OM shall be kept for later use and consulted for clarifications if required. If the

turnstile is resold, handed over to another owner or transported to another place, make sure that

the OM is enclosed to the turnstile to be used by new owner and/or maintenance staff during

installation and/or operation.

Safety measures and requirements specified in this in this OM must be observed:

–the turnstile must be connected to ground loop prior to operation;

–the turnstile should be connected to AC network with parameters specified in paragraph

1.2 "Specifications";

–іnspection, adjustment and repair should be performed only after the turnstile is

deenergized.

After purchasing of the turnstile it should be unpacked and its integrity should be checked.

In case of doubt in integrity of the turnstile it should not be used and the customer should refer to

the supplier or to the manufacturer.

Packing accessories (wooden pallet, nails, clips, polyethylene bags, cardboard etc.) as

potential sources of hazard must be removed to unacceptable place prior to proper use of the

turnstile.

As electric shock protection device the turnstile is related to 01 protection class according to

GOST (State Standard) 12.2.007.0-75 and is not intended for operation in explosive and fire

hazardous areas by the "Rules for design of electrical installations".

Using of the turnstile for unintended purpose, improper installation, nonobservance of

conditions of transportation, storage, installation and operation, specified by this OM, may result

in damage to people, animals or property for which the manufacturer is not responsible.

Operation Manual 5

1. DESCRIPTION AND OPERATION

1.1 General Information and Purpose

1.1.1 Purpose:

The turnstile is designed for pedestrian movement control at access points of industrial

enterprises, banks, stadiums, administrative facilities etc. controlled by access control system

(from proximity card readers) or manually (from manual control panel).

The turnstile traffic flow capacity without personal identification is at least 20 persons per

minute in one direction.

1.1.2 The turnstile dimensions and weight correspond to the values specified in Table 1

Table 1

Model

Designation

modification

Access way

width

Dimensions, mm

Max.

weigh, kg

Height

Length

Width

Gate-TS

AUIA.203-01

Т3.KСН.SD

Т3.KСН.PD

Т3.KСН.KD

650

1000

225

815

900

1065

Gate-TTS

AUIA.203-02

700 -1050

1000

225

865-1215

Gate-GS

AUIA.203

Т3.KСC.SD

Т3.KСC.PD

Т3.KСC.KD

650

1000

225

815

900

1065

Gate-GSH

AUIA.203-03

650

1500

225

815

900

1065

Operation Manual 6

1.1.3 The operation condition parameters according to GOST 15150-69 for climatic

modification NF4 are specified in Table 2.

Operation conditions

Parameter value

Ambient temperature

+ 1 to + 40 °С

Relative humidity

80 % at 20 ºС (non-condensing)

Ambient temperature

allowable pressure

84 to 106,7kPa

Transportation temperature

range

- 40 to + 50 °С

Storage temperature range

- 5 to + 40 °С

Group of mechanical

application

Altitude above sea level

up to 2000m

Environment

Explosion-proof, does not contain current-conducting dust,

aggressive gases and vapours in concentration destroying

isolation and metals, disturbing normal operation of the

equipment installed in turnstiles

Installation site

In enclosed spaces in the absence of direct impact of

Fig. 1–Installation dimensions of the Swing Gate

type turnstile

Operation Manual 7

precipitations and solar radiation

Operating position

Vertical, deviation from vertical position no more than 1º to any

side is tolerated

1.1.5 Reliability indices:

 mean time to repair (without delivery time of spare parts, tools and accessories) – at most

6 hours;

mean time to failure – at least 5 000 000 accesses;

mean service life between overhauls – at least 10 years.

1.2 Specifications

The key parameters of the turnstile are specified in Table 3. Table 3

Parameter description

Parameter

Minimum traffic flow capacity in free access mode

60 man/min.

Opening time

2-5 s

Maximum access way width

- narrow leaf

- wide leaf

- telescopic leaf

650 mm

900 mm

700-1050 mm

Maximum access way width

100 240V

~ 50/60Hz

–AC power supply (primary)

–DC power supply (secondary)

12W

Maximum power consumption

55W

Index of protection according to EN 60529

IP41

1.3 Configuration and Scope of Delivery

1.3.1 The swing gate type waist-high turnstile design includes the following key devices

and components:

–housing;

–leaf;

–actuator;

–control unit;

The turnstile also includes control panel.

Design, overall and installation dimensions of the turnstile are shown in Annex A.

The turnstile modification is based on the leaf material

1) stainless steel leaf (reference designation T3.КCН.XD);

2) glass leaf (reference designation T3.КСС.XD).

The turnstile modifications are manufactured from:

– brushed stainless steel (reference designation T3.КXХ.SD).

– polished stainless steel (reference designation T3.КXХ.РD).

– carbon steel subject to painting (reference designation T3.КXХ.КD);

Operation Manual 8

“Gate-GS”* “Gate-TS”*

* The design of the turnstiles “Gate-GSH” and “Gate TTS” is the same as the design of the turnstiles

“Gate-GS” and “Gate-TS”

Legend:

1,2. - Base and assembly mechanism;

3. - Housing;

4. - Lid;

5. - Glass leaf or Stainless steel tubular leaf;

6. - Actuator and control unit;

7. –Glass holder or place for leaf fixation

Fig.2 - Design of the single turnstile “Gate-GS” and “Gate-TS”

Leaf options for gates АUIA.203:

«Gate GS»

Glass leaf

«Gate GSH»

High glass leaf

«Gate TS»

Stainless steel tubular

leaf

«Gate TTS»

Telescopic stainless

steel tubular leaf

Fig. 3–Leaf options “Gate” АUIA.203

1.3.2 Scope of Delivery

The turnstile is delivered by one package.

1.3.3 Design, overall and installation dimensions of the turnstile are shown in Annex А.

Operation Manual 9

1.3.4 The turnstile material of manufacture is carbon steel subject to painting, brushed

stainless steel or polished stainless steel.

1.4 Design and operation

1.4.1 General appearance of the turnstile

1.4.1.1 The swing gate consists of assembly mechanism 2 with fixed base 1. (Fig.4).

Housing 3 with leaf 5 from glass or tube is installed on the top of assembly mechanism 2.

1.4.1.2 On top of the turnstile housing 3, a lid 4 is installed with a welded screw, which is

screwed into the turnstile assembly mechanism 2, fixing the main elements of the gate.

1.4.1.3 Control unit and actuator 6 are located at the bottom of the turnstile housing.

Leaf is automatically brought to initial position by means of servomotor after each turnstile access.

Housing is connected with control unit and actuator 6 by means of screw with washers, providing

rotation of leaf to both sides at the angle of 90°.

1.4.1.4 Control unit 6 is a metal box installed on assembly mechanism 2. Power supply unit

and card, on which controllers with electronic components and connectors for peripheral

connections are fixed inside control unit.

Control unit is designed for the turnstile energization and latching control.

1.4.1.5 Control panel is a small desktop device in plastic case and is designed for setting and

indication of operating modes when the turnstile is operated manually. Control panel and its

connection diagram are shown in Annex В.

1.4.2 Principle of operation

1.4.2.1 Turnstile operating modes:

1) to be opened in the direction “A” or “B”;

2) free access in the direction “A” or “B”

Switching of the turnstile operating modes is performed either by control panel or as part of

automated access control system (ACS) (by means of cards, badges etc.).

1.4.2.2 In the initial state, when the turnstile is energized, leaf is locked from rotation in both

directions by actuator.

After access permission command in one of directions is received:

–leaf is unlocked;

–servo drive rotates leaf to the angle of 90° in the appropriate direction;

–after access permission command is cancelled, servomotor brings leaf back to initial

position and it is locked from rotation in both directions.

More detailed description of the turnstile operating modes is given in section 1.8

"Description and operation of controller as a component of the turnstile”

1.4.2.3 12V DC power voltage is provided by power supply unit.

1.4.2.4 The turnstile wiring diagram is shown in Annex C.

Operation Manual 10

a) “ Gate TS” b) “Gate GS”

Legend:

1 –Base;

2 –Assembly mechanism;

3 –Housing;

4 –Lid with screw М12;

5 –Glass leaf or stainless steel tubular

leaf;

6 –Actuator and control unit;

7 –Screws М16х22 -2 pcs.(for stainless steel tubular leaf)

or countersunk screws А2 М6х16-4pcs. with spring and

flat washer (for glass leaf)

8 –Anchor М12;

9 –Shaft of top support;

10 –Protective case of control unit;

11 –Screws of protective case;

Fig. 4 –Design of swing gate AUIA.203

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Tiso Tourniquet

Tiso

Tiso CENTURION-M TWIN Manuel utilisateur

Tiso

Tiso ASTM F2656 M40 Manuel utilisateur

Tiso

Tiso SpeedBlade T3.KCD.XV.X Series Manuel utilisateur

Tiso

Tiso TRACK-AS-YOU-GO PRO Manuel utilisateur

Tiso

Tiso T1.1.BYO Series Manuel utilisateur

Tiso

Tiso JETPAN Manuel utilisateur

Tiso

Tiso T3.PKC.XC Manuel utilisateur

Tiso

Tiso ASTM F2656 M50 Manuel utilisateur

Manuels Tourniquet populaires d'autres marques

Oxgard

Oxgard CUBE C-10 Manuel utilisateur

LBA GROUP

LBA GROUP LBAT10 Manuel utilisateur

Magnetic

Magnetic mTripod Manuel utilisateur

Kaba

Kaba Argus HSG-E02 Manuel utilisateur

Automatic Systems

Automatic Systems TR491 Manuel utilisateur

Turnstiles

Turnstiles HZ-SWGS01 Manuel utilisateur

DSI

DSI DST-80 Manuel utilisateur

OZAK

OZAK VP-125 Manuel

Automatic Systems

Automatic Systems SMARTLANE SL 90X Manuel utilisateur

Alvarado

Alvarado MT Instructions d'installation et d'utilisation

JKDC SECURITY

JKDC SECURITY JKDC-100C Manuel utilisateur

Alvarado

Alvarado SU5000 Manuel utilisateur

Magnetic Autocontrol

Magnetic Autocontrol MPT 33 Manuel utilisateur

Oxgard

Oxgard Praktika T-04K Guide de démarrage rapide

digicon

digicon CATRAX Plus Manuel utilisateur

Oxgard

Oxgard CUBE C-04-s Manuel utilisateur

BOON EDAM

BOON EDAM Turnlock 100 Mode d’emploi

Wano

Wano Tripod BO-DSN10 Manuel utilisateur