Timeguard SL311 Manuel
)
INSTALLATION & OPERATING
INSTRUCTIONS
SENSOR LIGHT
Cat No. SL311
SL311_Instructions.qxd 2/5/06 4:22 pm Page
21
SL311 Sensor Light
Please read the instructions before using the
product and retain for future use.
Lamp
diffuser
On/Off/Auto
switch
Krypton bulb –
70% brighter than
standard bulb
PIR sensor
and lens
Light
sensor
Lamp diffuser
retaining screw
SL311_Instructions.qxd 2/5/06 4:22 pm Page
32
Features
• As a convenience aid, the unit provides you
with a light when you need it, in such dark
places as stairways, basements and car park
entrances. No need to search for the
lightswitch.
• It uses a built-in passive infra-red (PIR)
sensor that instantly detects moving body
heat and activates the built-in light when
someone moves within the detection area.
• It lights instantly and remains on as long as
there is a moving heat source in the area. The
light will switch off 20 seconds after the last
detection is made.
• A light sensor is incorporated to prevent
operation during daylight hours.
• Energy saving – you will never forget to turn
this light off because in auto your light is
only on when you need it.
SL311_Instructions.qxd 2/5/06 4:22 pm Page
43
Battery installation
The unit operates on 6V DC,
supplied by 4 AA alkaline
batteries.
Remove battery compartment
cover by pressing down on the
arrow and sliding outwards.
Insert batteries into the battery
compartment with correct
polarity as indicated and slide
cover shut.
Bulb replacement
A spare bulb is included in the pack.
Using a cross head screwdriver remove
the lamp diffuser screw. Pull the diffuser
outwards at the top and then lift it clear of the
lamp body.
Unscrew the lamp (anti-clockwise) and
remove it.
Make sure the new bulb is screwed tightly into
the holder (finger pressure only), then replace
the diffuser and fixing screw.
Battery cover
Fixing hole
SL311_Instructions.qxd 2/5/06 4:22 pm Page
4
Detection area
Position the unit so that potential paths taken by
people cut across the beams as shown below and
not directly at them.
The unit should be fitted about 1 to 1.5 metres above the
ground. It should not be mounted near or pointing at air
conditioning vents, near heating flues or above radiators,
or aimed at the road where passing cars may activate it.
Please note this PIR light will only operate in darkness
and therefore can only be tested in a darkened room.
Note: the light detection pattern may vary with climatic
conditions. Sporadic activation is also possible due to
large electrical supply fluctuations or poor electrical
connections in the premises.
Fig. 1
Fig. 2
10M
1.5M
10M1M 5M
✗
✓
SL311_Instructions.qxd 2/5/06 4:22 pm Page
65
Operation
1 Set the switch to ON. The lamp should light up.
2 Set the switch to Auto. The lamp will function if:
1. It is after dusk. 2. There is a moving heat
source in the area (body heat).
1 Warm-up Period:
The lamp will light for around 40 seconds while the
PIR sensor stabilises. It will then turn off waiting for
the first detection.
2 First Entry:
The lamp will light when a moving heat source enters
the detection area. It remains on as long as there is a
moving heat source present.
3 Switch-off Delay:
When the heat source leaves the detection area the unit
will automatically shut off after 20 seconds.
5 Second Entry:
The lamp will light again when a moving heat source
enters the detection area. It remains on as long as a
heat source is moving, turning off 20 seconds after the
last detection.
4 Reset:
The unit is immediately ready to detect again.
SL311_Instructions.qxd 2/5/06 4:22 pm Page
6
Specifications
Area of Coverage: 6m x 90° wide (fan shaped)
at 20°C. High temperature
environment may decrease
the detection range.
Detection Method: Passive Infra-Red (PIR)
sensor detects moving
thermal radiation
Battery Type: 4 x AA alkaline (not included)
Battery Life: 1 month (on the basis of
8 x 20 second detections
per day)
Power Consumption: 0.015 watts with light off.
3 watts with light on.
Output: Bulb (krypton) 4.8V,
0.5A, MES (Spare bulb
included in pack)
AC Mains Adaptor: 6V DC, 600mA or above
(not included) (female centre negative)
Reset Time: Instant
Built-in photocell keeps the unit off in daylight hours.
Housing designed for indoor use only.
SL311_Instructions.qxd 2/5/06 4:22 pm Page
5
HELPLINE
020-8450-0515
For a product brochure please contact:
Timeguard Ltd.
Victory Park, 400 Edgware Road,
London NW2 6ND
020-8452-1112
3 Year Guarantee
In the unlikely event of this product becoming faulty due
to defective material or manufacture within 3 years of the
date of purchase, please return it to your supplier in the
first year with proof of purchase and it will be replaced
free of charge.
For the second and third years or any difficulty in the first
year telephone the helpline on 020 8450 0515.
SL311_Instructions.qxd 2/5/06 4:22 pm Page
Table des matières
Autres manuels Timeguard Éclairage extérieur
Manuels Éclairage extérieur populaires d'autres marques
Lindby
Lindby 9949029 Manuel utilisateur
HEPER
HEPER DOGO Side LW6048.585-US Instructions d'installation et d'utilisation
HEPER
HEPER LW8034.003-US Instructions d'installation et d'utilisation
Maretti
Maretti VIBE S 14.6080.04.A Manuel utilisateur
BEGA
BEGA 84 253 Manuel
HEPER
HEPER MINIMO Instructions d'installation et d'utilisation
LIGMAN
LIGMAN BAMBOO 3 Manuel utilisateur
Maretti
Maretti TUBE CUBE WALL 14.4998.04 Manuel utilisateur
Maxim Lighting
Maxim Lighting Carriage House VX 40428WGOB Manuel utilisateur
urban ambiance
urban ambiance UQL1273 Manuel utilisateur
TotalPond
TotalPond 52238 Manuel utilisateur
Donner & Blitzen
Donner & Blitzen 0-02661479-2 Manuel utilisateur