Timeguard PDFMMINIL Manuel

Installation & Operating Instructions

360° Flush Mount Ceiling

PIR Light Controller

Model: PDFMMINIL

Mini Recessed PIR Master Linkable

and Power Box

Model: PDFMMINILS

Mini Recessed PIR Slave Linkable

1 2

1. General Information

These instructions should be read carefully and retained for further reference

and maintenance.

2. Safety

• Before installation or maintenance, ensure the mains supply to the PIR sensor

is switched off and the circuit supply fuses are removed or the circuit breaker

turned off.

• It is recommended that a qualified electrician is consulted or used for the

installation of this PIR sensor and install in accordance with the current

IEE wiring and Building Regulations.

• Check that the total load on the circuit including when this PIR sensor is fitted

does not exceed the rating of the circuit cable, fuse or circuit breaker.

3. Technical Specifications

Power Box

• 230V AC 50 Hz

• This Power Box is of Class ll Construction and must not be earthed

• Maximum Switching Load; 2300W Halogen

500W Low loss balance fluorescent

250W Electronic balance fluorescent,

CFL and LED Lighting

• Mounting Centres: 165mm

• Manual Override Mode: Double pulse within 2 seconds to enter

6 hours ON time

• IP20 Rated suitable for restricted internal applications

• CE Compliant

• Dimensions: H= 35mm, W= 175mm, D= 35mm

• The power box will fit through a 40mm diameter hole

2 3

Master PIR Sensor

• These PIRs are of Class lll Construction and must not be earthed

• Motion Detection Range: 8m diameter at a 2.5m mounting height

• Presence Detection Range: 3m diameter

• Detection Angle: 360°

• Time ON Adjustment: 30 seconds to 30 minutes

• Warm Up Time: 60 seconds

• LUX level adjustment: 10 to 2000 Lux

• Operating Temperature: -20°C to +40°C

• Ceiling Cut Out: 40mm diameter hole

• Connection Cable: Pre-fitted 250mm long cable with

an RJ11 connector

• IP40 Rated suitable for restricted internal applications

• CE Compliant

• Dimensions: 47mm diameter body, 64mm height

Slave PIR Sensor

• These PIRs are of Class lll Construction and must not be earthed

• Motion Detection Range: 8m diameter at a 2.5m mounting height

• Presence Detection Range: 3m diameter

• Detection Angle: 360°

• Warm Up Time: 60 seconds

• Operating Temperature: -20°C to +40°C

• Ceiling Cut Out: 40mm diameter hole

• Connection Cable: Pre-fitted 5m long cable with an RJ11 connector

• IP40 Rated suitable for restricted internal applications

• CE Compliant

• Dimensions: 47mm diameter body, 64mm height

Multiple PIR Sensor Switching – A maximum of 5 PDFMMINILS Slave PIR

sensors can be linked to the PDFMMINIL Master PIR, to enable any detector

to turn ON all the lights connected (The total load must not exceed the lamp

rating of a single PDFMMINIL unit).

Ø = 40mm

3 4

4. Installation Advice

As the PIR sensor responds to changes in temperature,

avoid the following situations:

• Mounting the sensor near objects with highly reflective surfaces,

such as mirrors etc.

• Mounting the sensor near heat sources, such as heating vents,

air conditioning units, lights etc.

• Mounting the sensor near objects that may move in the wind,

such as curtains, tall plants etc.

5. Installation

5.1 Ensure the mains supply is switched OFF

and the circuit supply fuses are removed

or the circuit breaker turned off.

Ø = 40mm

5.2 An isolating switch should be

installed to enable the power

to be switched ON and OFF for

maintenance purposes and to

activate the manual override function.

5.3 Mark the position of the 40mm

diameter locating hole centre,

taking care to avoid ceiling joists

and other obstructions within

the 40mm diameter.

5.4 Use a pad saw or suitable hole cutter

to cut out a 40mm diameter hole.

5.5 Pass the 230V 50Hz mains supply

and load cables through the hole

and prepare for termination.

5.6 Undo the 2 fixing screw located

on the far end of the power box

and remove the terminal block

cover (opposite side to the RJ11

connection socket).

5.7 Terminate the cables into the

terminal block ensuring correct

polarity is observed and that

all bare conductors are sleeved

(See section 6. Connection Diagram).

5.8 Re-attach the terminal block cover.

5.9 Use the 2 fixing screw to secure

into place.

Ø = 40mm

5 6

5.10 Insert the power box through the 40mm hole into the ceiling first, followed

by the RJ11 cable from the master PIR sensor. Connect the RJ11 cable into

the socket on the power box. Fix the master PIR sensor into position using

the metal springs.

Note: A maximum of 5 PDFMMINILS Slave PIR sensors can be linked to the

PDFMMINIL Master PIR sensor, to enable any detector to turn ON all the lights

connected (The total load must not exceed the lamp rating of a single

PDFMMINIL unit).

Example:

230V 50Hz

MAINS SUPPLY

ISOLATION

SWITCH

Loop Terminal

PDFMMINIL Power Box

LAMP

230V 50Hz Mains Supply

Live Supply (Brown or Red) to L

Neutral Supply (Blue or Black) to N

A ‘Loop Terminal’ (centre terminal) is provided should a 3 core

cable be used

Load

Switched Live (Brown or Red) to L1

Neutral Load (Blue or Black) to N

6 Connection Diagram

• Connect the 230V 50Hz mains supply cables to the terminal block

in the power box as follows;

Ø = 40mm

7 8

HELPLINE

020 8450 0515

7. Setting Up

Walk Test Procedure

• The adjustable LUX and TIME setting controls are factory set to ‘Walk Test’

mode i.e. LUX set fully clockwise to full daylight (Sun symbol) and the TIME set

fully anti-clockwise to ‘T’ (Test mode)

• Turn the power to the unit ON.

The lamp will immediately illuminate

as the unit goes through its ‘warm-up’

period. After approximately 30 seconds

to 1 minute the lamp will extinguish.

This indicates the unit is wired

correctly and the unit is in Test Mode.

• Try to remain outside the detection ‘zone’ during the warm-up period.

• The unit will now operate during daytime as well as at night, illuminating

the lamp for approx. 2 seconds each time. This allows testing to be carried

out to establish whether the sensor is covering the required ‘zone’.

• Walk around the sensor to establish the detection ‘zone’.

• The sensor will detect within an approximately 8 metre diameter circle

from the centre of the sensor location with a 2.5m ceiling.

• As you cross a detection ‘zone’ the lamp will illuminate. Now stand still

until the lamp extinguishes (this should take approx. 2 seconds).

• Start moving again after 5 seconds. As you continue to cross the detection

‘zone’ the lamp will illuminate.

• Repeat the above, walking at various distances and angles to the unit.

This will help you to confirm the detection pattern.

Setting Up for Automatic Operation

• When walk tests are complete, the unit can be adjusted for

automatic operation (Auto Mode).

Note: there is a flat headed screwdriver included in the accessory pack

which you can use to make the adjustments.

Ø = 40mm

• To access the setting controls, rotate

the sensor body within its housing

anti-clockwise and pull the sensor

body downwards.

Note: there are no setting controls on the PDFMMINILS

slave PIR sensor, only on the PDFMMINIL master PIR sensor.

• The TIME setting controls how long the unit remains illuminated

following activation and after all motion ceases.

• The TIME control knob at fully anti-clockwise ‘T’ is Test Mode. You can adjust

the TIME as marked 30secs, 2min, 5min, 10min, 15min and 30min max.

• Set the control to the desired setting.

• The LUX control determines the level of darkness required for the unit to start

operating. The setting is best achieved by the procedure below;

1. Make sure the LUX control knob is set fully clockwise (Sun symbol).

2. When the ambient light level reaches the level of darkness at which you wish

the lamp to become operative (i.e. at dusk) SLOWLY rotate the control in an

anti-clockwise direction (towards the moon symbol) until a point is reached

where the lamp illuminates.

3. Leave the control set at this point.

Ø = 40mm

• At this position the unit should become operative at approximately

the same level of darkness each evening.

• Observe the operation of the unit. If the unit is starting to operate too early

(i.e. when it is quite light) adjust the control slightly anti-clockwise.

If the unit starts to operate too late (i.e. when it is very dark).

Adjust the control slightly clockwise.

• Continue to adjust until the unit operates as desired.

• Once the unit is set up as desired,

push the sensor body fully upwards

into its housing and rotate

clockwise to lock into place.

8. Lens Mask

• There is 1x lens mask included in the accessory pack.

• The purpose of the lens mask to mask out areas not desired for detection.

You can restrict left or right detection, or reduce the 8 metre diameter

to cover a smaller ‘zone’.

• Use some pliers or a suitable tool to cut out the mask segment,

exposing the required ‘zone’ of detection.

• Attach the lens mask to the sensor head,

turning it slightly to lock into place.

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels Timeguard Contrôleurs

Timeguard

Timeguard RTS113Q Manuel de programmation

Timeguard

Timeguard ProgramaSTAT UFPT24 Manuel utilisateur

Timeguard

Timeguard SLFM360 Manuel

Timeguard

Timeguard PDFM1500 Manuel

Timeguard

Timeguard E269H-Synchronous Manuel

Timeguard

Timeguard PDSM1500 Manuel

Timeguard

Timeguard SLB2300RF Manuel

Timeguard

Timeguard SLB2300RF Manuel

Timeguard

Timeguard SLFM360L Manuel

Timeguard

Timeguard TLRX05 Manuel

Timeguard

Timeguard SLW360L Manuel

Timeguard

Timeguard SLFM360N Manuel

Timeguard

Timeguard TS900B Manuel utilisateur

Timeguard

Timeguard SLB2300 Manuel

Timeguard

Timeguard RTS113 Manuel de programmation

Timeguard

Timeguard MTLW3000 Manuel

Timeguard

Timeguard SLDD1000 Manuel

Timeguard

Timeguard MLSA360N Manuel

Timeguard

Timeguard PDRS1500N Instructions d'installation

Timeguard

Timeguard TRT039N Manuel

Timeguard

Timeguard MLB3000 Manuel

Timeguard

Timeguard PDFM1500N Manuel

Timeguard

Timeguard TS900N Instructions d'installation

Timeguard

Timeguard SureTime STLW1000 Manuel

Manuels Contrôleurs populaires d'autres marques

Digiplex

Digiplex DGP-848 Mode d'emploi

YASKAWA

YASKAWA SGM series Manuel utilisateur

Sinope

Sinope Calypso RM3500ZB Manuel utilisateur

Isimet

Isimet DLA Series Style 2 Manuel d'installation

LSIS

LSIS sv-ip5a Manuel utilisateur

Rockwell Automation

Rockwell Automation 1769-L31 Manuel utilisateur

Airflow

Airflow Uno hab Manuel utilisateur

ABB

ABB ACS580-01 drives Manuel utilisateur

Panasonic

Panasonic GM1 Series Manuel utilisateur

Emerson

Emerson SW93 Manuel utilisateur

AutoAqua

AutoAqua Smart ATO micro SATO-120P Manuel utilisateur

Panasonic

Panasonic FP? Positioning Unit RTEX Manuel utilisateur

Samson

Samson Type 5824 Manuel de service

Alpha IP

Alpha IP MIOB 21001 Manuel utilisateur

Siemens

Siemens OpenAir GMA 1 Series Manuel utilisateur

Surecom

Surecom SR-629 Manuel utilisateur

Fishman

Fishman TriplePlay Manuel utilisateur

Regulus

Regulus SRS1 T Manuel utilisateur