THORENS TD160 Manuel utilisateur

Fit

ting

The Wand

Tonearm

to a

Thorens TD160

family

turntable

(TD150/166 similar)

You should be able to use the Thorens arm lifter with The Wand Tonearm To be read in conjunction with The Wand User Guide.

A; Remove the existing arm

Step 1; Remove the platter, headshell and Step 2; Support the turntable upside down

Lifter bar (arrowed) Disconnect from power! and remove the bottom cover. 4 screws.

Step 3; Remove the arm cable clamp and Step 4; Unhoo the lift mechanism

the white cable cover.

Step 5; Remove the cable base (Two screws) Step 6; Remove the armrest (two screws)

Step 7; Turn over and remove the arm.

(Three screws)

Hint; Improve your Thorens by adding

damping material to the underside of the

sheetmetal panels and the bottom cover while it is

off. (but watch adding too much weight to the

floating chassis part)

www.thewandtonearm.com

©Sept 2016 design build listen Ltd. v2

Fitting The Wand Tonearm®

to a Thorens TD160

family turntable

(TD150/165 similar)

You may choose to use the Thorens arm lifter with The Wand To be read in conjun

ction with The Wand User Guide.

B; Prepare The Wand ounting

Step 1; Stac the Steel plate on top of blac acrylic

Step 2; Add the Wand mount & feed through the plinth

(Wand Classic left, Wand Plus right below)

Step 3; Screw in but don’t tighten. (Three screws) Step 4; Add earth wire to amplifier.

(as below) or 3 core mains cable.

Step 5; Add the Thorens lifter to the underside (if you are using it) Use 2x self-tapping screws.

See previous page for correct orientation. Re-connect

the lifter cable.

www.thewandtonearm.com

©Sept 2016 design build listen Ltd. v2

Note

; If you want to route the

wiring into the plinth. Feed

through the slot in the Wand

mount before adding screws.

(But good to ‘practice’ the other

steps first)

Fitting The Wand Tonearm®

to a

Thorens

TD160

family turntable

(TD150/165 similar)

C; Fitting The Wand Tonearm ount

Step 1; Install the spindle into mounting plate. Set the spindle height using the protractor.

Loc in position using the nut (Classic) or grub screw (Plus).

Step 2; Position the mount using the Step 3; Tighten the three screws

protractor (Slide bac and forth)

Step 4

;

Add the Lifter

(Wand Plus on left / Thorens for Classic on right.

Step 5; Revert to main instructions for the remainder of the setup and enjoy!

www.thewandtonearm.com

©Sept 2016 design build listen Ltd. v2

-Arm at +2 degrees

-Arm level (nominal)

Note; We suggest

starting with the arm

level. Later adjust

upwards by ear. Up to 2

degrees up may be good.

<Spindle

< Nut

v Plate

“The improvement over the

Thorens arm is astonishing.

Detail, timing, but most of all

soundstage depth.”

Richard, Dunedin, New Zealand

Align to just below the step.

Loc with small hex ey.

Slide up / down to set lift

Height (very fiddly!)

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels THORENS Platine

THORENS

THORENS TD201 Manuel utilisateur

THORENS

THORENS TD 280 Mk IV Manuel utilisateur

THORENS

THORENS TP 190 Manuel utilisateur

THORENS

THORENS TD 170-1 Manuel utilisateur

THORENS

THORENS TD 524 Manuel utilisateur

THORENS

THORENS TD 403 DD Manuel utilisateur

THORENS

THORENS TD 903 Manuel utilisateur

THORENS

THORENS TD 165 Manuel utilisateur

THORENS

THORENS TD 103 A Manuel utilisateur

THORENS

THORENS TD 158 Manuel utilisateur

THORENS

THORENS 900 Series Manuel utilisateur

THORENS

THORENS mini Manuel utilisateur

THORENS

THORENS TD 700 Manuel utilisateur

THORENS

THORENS TD 240-2 Manuel utilisateur

THORENS

THORENS TD402 DD Manuel utilisateur

THORENS

THORENS TD 295 MK IV Manuel utilisateur

THORENS

THORENS TP 82 Manuel utilisateur

THORENS

THORENS TD 2001 Manuel utilisateur

THORENS

THORENS TD 147 Manuel utilisateur

THORENS

THORENS TD 240 Manuel utilisateur

THORENS

THORENS TD 850 Manuel utilisateur

THORENS

THORENS TD 235 Manuel utilisateur

THORENS

THORENS TD 2035 Manuel utilisateur

THORENS

THORENS TD 203 Manuel utilisateur

Manuels Platine populaires d'autres marques

Gemini

Gemini CDT-05 MKII Manuel utilisateur

Rotel

Rotel RP-820 Manuel utilisateur

Shuman

Shuman MC-250BT Manuel utilisateur

Stanton

Stanton STR8-150 Manuel utilisateur

Audio Technica

Audio Technica AT-LPW40WN Manuel utilisateur

Crosley

Crosley McQueen CR7011-GY Manuel utilisateur

Reloop

Reloop SMP-1 Manuel utilisateur

auna

auna TT-Classic Plus Manuel utilisateur

COMO AUDIO

COMO AUDIO Turntable Analog Manuel utilisateur

Dual

Dual 1009 F Manuel utilisateur

REED

REED Muse3C Manuel utilisateur

AXIOMTEK

AXIOMTEK OPS883-H Series Manuel utilisateur

Pioneer

Pioneer PL-71 Manuel utilisateur

Vestax

Vestax PDX-a1 Manuel utilisateur

Denon

Denon DP-400 Manuel utilisateur

Dual

Dual 504 Manuel utilisateur

Audio-Techica

Audio-Techica AT-LP60XBT Manuel utilisateur

Goldring

Goldring G99 Manuel utilisateur