THOMSON EFC031E Manuel

Televisión

IINNFFOORRMMAACCIIOONNTTEECCNNIICCAA

Chasis IFC130 (PLASMA - LCD)

Alimentación

Circuito de deflexión_H

Circuito de deflexión_V

Circuito RF-FI

TRC - Pantalla

Conectores - Scart

Mecánica

Panel de control

Tratamiento de datos

Tratamiento de audio

Sección :

Tratamiento de video

General

1 - ACCESING SERVICE MODE

EFC031E

1.1 TV set ON.

1.2 While keeping pressed the ”VOL-” key on the TV keyboard

press ”EXIT” on the RC until TV set switch on and enter service mode.

(Main menu).

IFC130 - EFC031E (according software version)

1.1 Switch the TV set into the Standby Mode.

1.2 While keeping pressed the ”VOL-” key on the TV keyboard press

”VOL-” on the RC until TV set switch on and enter service mode (Main menu).

2 - TEMPORARY EXIT FROM SERVICE MODE

2.1- 2.1- To temporary leave the Service Mode from the Main menu, goto the point ”Return”.

To access the everyday menus, press the ‘’Menu’’ button on the RCU.

Note :

- According to the type RCU it is possible to temporary leave the Service Mode by pressing Exit or Return key.

RETURN TO THE MAIN MENU

EFC031E

2.2 - To return to the Main menu, While keeping pressed the ”VOL-” key on the TV keyboard press

”Exit” on the RC until TV set switch on and enter service mode.

IFC130

2.2 - To return to the Main menu, press on the magenta key (”text”) on the RCU.

Note :

- A IFC130 menu not used during 3 minutes disappears. Press on the magenta key (”text”) on

the RCU to return to the Main menu.

3 - EXITING FROM SERVICE MODE

3.1- To exit the Service Mode switch off the mains supply to the TV.

All change in service mode will be saved in EEPROM automatically.

4 - EXITING FROM A SUB-MENU

4.1- To exit from a Sub-Menu (see §8) and return to the Main menu press the ”Exit key or the ”Return” key on the

RCU.

5 - NAVIGATION INSIDE THE SERVICE MODE

TV CONTROL PANEL

EFC031E - IFC130

First issue 02 / 06 1

I - SERVICE-MODE

(

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

EFC031E MAIN MENU

- Selec option*

- “Change value“

navigation up Navigation down

VALUE

Vol. +

Vol.

VOL

(

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

(

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

➠

(

Service Menu

BL1.41

Return

Sound

Video

SAA7117AE

...

PW2300 ...

Misc ...

PW218 1st page ...

PW218 2nd page ...

IFC130 MAIN MENU

* Select option is possible with ”OK”

REMOTE CONTROL

EFC031E - IFC130

2First issue 02 / 06

6 - DISPLAYING THE VALUE OF THE SETTING

VIDEO

7 - TOGGLE FUNCTION

To enable a function check (tick) the box.

: Implemented function : No implemented function

(Brightness -0003

Affichage

➠ + >NVM valeur Affichage

➠

<NVM valeur

Valeur décimale

Valeur de réglage

: NVM valeur

➠

OK PR

VOL

(

Factory setting

EFC031_X181-0

Return

Sound

Miscellaneous

Video

Field Service

...

Alignment

Alignement

Ableigh

Regolazione

Alineacion

Software version

Version Software

Software Version

Versione softaware

Versión software

- Select option*

- “Change“value

(

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

(

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

➠

Navigation up Navigation down

VALUE

* Select option is possible with ”OK”

8 - LITE MENU FOR FIELD SERVICE

MAIN MENU

EFC031E - IFC130

First issue 02 / 06 3

(

Factory setting

EFC031_X181-0

Return

Sound

Miscellaneous

Video

Field Service

...

Alignment

Alignement

Ableigh

Regolazione

Alineacion

Software version

Version Software

Software Version

Versione softaware

Versión software

SUBMENU

EFC031E - IFC130

4First issue 02 / 06

II - EFC031E CHASSIS - ALIGNMENT

1 VIDEO

1.1 Conditions

- The TV set should be warmed up for 60 minutes.

- The following conditions are automatically set when entering the Video submenu.

* Set these conditions in the User menu

1.2 Y, Pb, Pr Component Input

Video test pattern

1.3 VGA Input

Standard Monitor Format (VESA) Standard TV Display Format

Test

Pattern

Philips test pattern 12 steps greyscale

Format 4:3 16:9 4:3 16:9

1H 576i25Hz 1080i25H

576i25Hz 1080i25Hz

2H 576p50Hz 720p60Hz 576p50Hz 720p60Hz

Test

Pattern

Philips test pattern 12 steps greyscale

Picture

Format 4:3 16:9 4:3 16:9

1H 576i25Hz 1080i25H

576i25Hz 1080i25Hz

2H 576p50Hz 720p60Hz 576p50Hz 720p60Hz

Test

Pattern

Philips test pattern 12 steps greyscale

Format 640x480@60Hz,

800x600@85Hz,

1280x1024@75Hz

640x480@60Hz,

800x600@85Hz,

1280x1024@75Hz

Function Alignment Value

Brightness Standard

Colour Standard

Contrast Standard (70%)

Black Extand Off...*

Tone Neutral...

Sharpness Not applicable*

Noise reduction Off...*

Couleur NTSC 50%

Mode zoom Standard

EFC031E - IFC130

First issue 02 / 06 5

1.4 Video Calibration

EFC031E

1.4.1 MST9883 ADC Calibration

YPbPr Calibration for TV display format

- Connect Y, Pb, Pr signal to BV280 connector (”Video Components Enter”) with the following standard.

Input signal parameters:

- Exit temporary from Service Mode and select the ”Video Components Enter”(press the magenta key on the

RCU ”Text”to come back at the service mode )

- Video pattern to calibrate

- Select YPbPr and ”Calibration”in the ”Miscelaneous”Menu of Sevice Mode and press on

the RCU OK key .

The screen is flashing few minutes and stable after few seconds.

Signal Value (Vp-p)

Y: Sync to Peak white 0.7

Pr:Sync to Peak white 0.7

Pb:Sync to Peak white 0.7

Calibration Pattern Color bar with no Gamma correction

Picture

Format 480p60Hz, 1H, 4:3

(

Factory Misc

(

Reset the values to ROM default

Yes?

LUMA_TEMPORAL-NR

CHROMA_TEMPORAL-NR

Calibration ...

Debug ...

Reset the Alignment values

Yes?

TT 27Y24 Packet Enable*

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

* According software version

...

Miscellaneous ...

EFC031E - IFC130

6First issue 02 / 06

1.4.2 RGB

RGB Calibration for Standard monitor format (VESA)

- Connect R, G, B Hsync and Vsync with following standard into VGA BV300

connector:

- Exit temporary from Service Mode and select the VGA enter (press the magenta key on the RCU ”Text”to come

back at the service mode)

- Video pattern to calibrate

- Select ”Calibration”in ”Miscelaneous”Menu of the Service Mode and press on the RCU ”OK”key.

The screen is flashing few minutes and stable after few seconds.

Note:

The others items of the ”Miscellaneous”menu are described at §4.

Signal Value (Vp-p)

R (Red) 0.7

G (Green) 0.7

B (Blue) 0.7

Hsync. 2.4V

Vsync. 2.4V

Calibration Pattern 16 step Gray scale with no gamma

correction

Picture

Format 800x600@85Hz

EFC031E - IFC130

First issue 02 / 06 7

2.1 Cut Off

Cutt Off alignment has to be done for the following standards :

Note: After Cut Off alignment control white point alignment. Repeat the adjustments if necessary.

R offset

G Offset

B Offset

+0007

+0024

+0016

- Insert a grey test pattern giving 15 Nits luminance level

- Measure the color co-ordinates near the screen center.

- Fix B Offset to the centre of the alignment range.

- Adjust R Offset - G Offset:

Colour Co-ordinates Value

x 0.282

y 0.293

Input Video Standard

SCART PAL / SECAM/ RGB

YPbPr SDTV (576i)

HDTV (108i 25)

HDTV (720p 60)

VGA VESA (DMT 1060)

SD Video (576i)

HD Video (1080i 25)

HDMI HDTV (720p 60)

FAV (CVBS) SD Video (576i)

(

Factory video

(Cut Off Alignment ...

Whitepoint alignment ...

Scalling Brightness Alignment...

Scalling Color Alignment ...

Scale Tint Alignment ...

Peak White Alignment ...

Text Contrast alignment ...

Preset for Video Alignment ...

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

...

Miscellaneous ...

EFC031E

2.2 Whitepoint

- Whitepoint alignment has to be done for the same standards of the Cuttoff alignment :

2.3 Scaling Brightness Alignment

-The Scalling Brightness is a factory alignment.

EFC031E: Brightness = +0003

R Gain

G Gain

B Gain

+0496

+0531

+0513

- Insert a grey test pattern with 50 IRE in one of the above mentioned standards.

- Measure the color co-ordinates near the screen center.

- Fix B Gain to the centre of the alignment range.

- Adjust R Gain - G gain to the following color co-ordinates:

Colour Co-ordinates Value

x 0.282

y 0.298

Brightness -0003

2 - VIDEO ALIGNMENT

EFC031E - IFC130

8First issue 02 / 06

2.4 Scaling Colour

- Scaling Color Alignment has to be done for the following standards :

- 75% Color bar test pattern.

- Measure the Blue output and adjust Colour to equal levels as shown bellow:

2.5 Scale Tint

-No alignment for EU models.

2.6 Peak White Alignment

- Peak White test pattern (100%).Colourimeter.

- Peak White alignment has to be done for the following standards :

- Adjust Contrast to the level : 450 Nits +20% -15%.

2.7 Text Contrast.

- Selecting this item inserts a white centered pad.

-Measure the optical luminance output level (Y Nits) of the white pad.

- Adjust Text Contrast to the 60% of the PW level.

Colour +0512

Input Video Standard

SCART PAL / SECAM/ RGB

YPbPr SDTV (576i)

HDTV (108i 25)

HDTV (720p 60)

VGA VESA (DMT 1060)

SD Video (576i)

HD Video (1080i 25)

HDMI HDTV (720p 60)

FAV (CVBS) SD Video (576i)

NTSC Tint +0000

Contrast +0534

Input Video Standard

SCART PAL / SECAM/ RGB

YPbPr SDTV (576i)

HDTV (108i 25)

HDTV (720p 60)

VGA VESA (DMT 1060)

SD Video (576i)

HD Video (1080i 25)

HDMI HDTV (720p 60)

FAV (CVBS) SD Video (576i)

Contrast +0534

Text Contrast 14

EFC031E - IFC130

First issue 02 / 06 9

3 - SOUND

- The items of the SOUND menu are not used

4 - MISCELLANEOUS

- EFC031E

4.1 Reset the values to ROM default

- Reset all the EEPROM data to FF.

Only required if the EEPROM data are corrupted.

After ”reset the values to ROM default”the alignment, calibration and channel installation is necessary.

4.2 LUMA_TEMPORAL_NR

- Temporal noise reduction setting for luminance.

Factory adjusted. It is not necessary to do adjustment on this item.

4.3 CHROMA_TEMPORAL_NR

- Temporal noise reduction setting for chrominance.

Factory adjusted. It is not necessary to do adjustment on this item.

4.4 Calibration

See §1.4

4.5 Debug

- Bus quiet mode for main I2C Bus. Used only in development purpose.

4.6 Reset the Alignment values

- Reset all alignment values to default value. Used only if the TV need new alignment.

In that case it is necessary to start alignments by Video Calibration (ADC YPbPr).

Note:

After loading of a new software select ”Reset the alignment values”and check the TV alignment.

4.7 TT 27Y24 Packet Enable

According to software version. Factory adjust.

Improve teletext performance for some special French channels

(

Factory Misc

(

Reset the values to ROM default

Yes?

LUMA_TEMPORAL-NR

CHROMA_TEMPORAL-NR

Calibration ...

Debug ...

Reset the Alignment values

Yes?

TT 27Y24 Packet Enable*

Factory setting

EFC031_X181-0

Return

Sound

Video

Field Service

* According software version

...

Miscellaneous ...

Ce manuel convient aux modèles suivants

Table des matières

Autres manuels THOMSON TV

THOMSON

THOMSON 72MK89D Manuel utilisateur

THOMSON

THOMSON 14MS15FT Manuel utilisateur

THOMSON

THOMSON 27LB125B5 Manuel utilisateur

THOMSON

THOMSON ITC008-V2 Manuel utilisateur

THOMSON

THOMSON 28VT68NE Manuel utilisateur

THOMSON

THOMSON ITC008B+ Manuel utilisateur

THOMSON

THOMSON RCA CR29TF420 Instructions de montage

THOMSON

THOMSON 21DG15CH Manuel utilisateur

THOMSON

THOMSON 20MF15GT Manuel utilisateur

THOMSON

THOMSON 28DT68L Manuel utilisateur

THOMSON

THOMSON 24WK23U Manuel utilisateur

THOMSON

THOMSON CR20300 Manuel utilisateur

THOMSON

THOMSON 15LCDM03B Manuel utilisateur

THOMSON

THOMSON DTI6300 Manuel utilisateur

THOMSON

THOMSON ZPN054102 Manuel utilisateur

THOMSON

THOMSON T32E53U Manuel utilisateur

THOMSON

THOMSON G27693 Mode d’emploi

THOMSON

THOMSON CR14300 Guide d'installation

THOMSON

THOMSON TX807 C Manuel utilisateur

THOMSON

THOMSON 28VT68ND Manuel utilisateur

THOMSON

THOMSON 23LB220S4 Manuel utilisateur

THOMSON

THOMSON DTH 8540 - Manuel utilisateur

THOMSON

THOMSON 21DU21C Manuel utilisateur

THOMSON

THOMSON 28VT68N Manuel utilisateur

Manuels TV populaires d'autres marques

Philips

Philips Colour Television Manuel utilisateur

Toshiba

Toshiba 27A10 Manuel utilisateur

Philips

Philips 42PF9630A/37 Manuel utilisateur

Hitachi

Hitachi 32FX48B Manuel utilisateur

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Manuel utilisateur

Changhong Electric

Changhong Electric uhd55b6000is Manuel utilisateur

Philips

Philips Matchline 21CE7551 Manuel utilisateur

Panasonic

Panasonic Genus TX-G10 Manuel utilisateur

Toshiba

Toshiba 19A20 Manuel utilisateur

Philips

Philips 25PT4523-16 Manuel utilisateur

Sony

Sony XBR-100Z9D Manuel utilisateur

Philips

Philips PR0930X3 Manuel utilisateur

Philips

Philips Brilliance 231P4QPY Manuel utilisateur

Samsung

Samsung 55S9 B Series Manuel utilisateur

Philips

Philips 32HF9385D Guide de dépannage

Sharp

Sharp LC-40FI5012E Manuel utilisateur

Loewe

Loewe Table Stand Reference 55 Manuel utilisateur

Philips

Philips 32PFH5300 Manuel utilisateur