ThermoWorks Thermapen Mk4 Manuel utilisateur

This procedure describes the method of trimming the Thermapen Mk4 at a

single temperature point (32°F/0°C) by using a properly made ice bath. The

Thermapen should rarely need adjustment and should only be performed if

absolutely necessary.

Materials Required:

• Philips screwdriver to open battery compartment

• Large kitchen cup (preferably 1 quart/1 liter size)

• Crushed ice (enough to ﬁll cup)

• Water

Determining if Your Thermapen Requires Adjustment:

1. Make a proper ice bath by following these steps:

• Fill a large cup with crushed ice.

• Add just enough water into the cup to ﬁll in the gaps in ice so no ice ﬂoats off the bottom of the cup. Too much water will

cause errors. Poor off water as necessary.

• Stir gently and wait approximately 1 minute.

2. Set the Thermapen display to read in tenths (example: 32.1°F) of a degree.

If the display is set to read temperature in whole degrees, change to tenths by following these steps below.

See video here: youtube.com/watch?v=O4k8m4lkDgk

• Using a Philips screwdriver, remove the battery compartment.

• Open the probe to turn on the Thermapen.

• Locate the Set and Menu buttons.

• Press the Menu button twice until 1 is displayed.

• Press the Set button to change the display from reading 1 to 0.1.

• To save the changes, press the Menu button until End is displayed.

• Replace the battery cover making sure not to overtighten.

3. Test the Thermapen display using the ice bath following these steps:

• Turn the Thermapen on by opening the rotating probe.

• Insert the tip of the metal probe into the ice bath about 2 inches (50mm) maximum.

• Stir gently so the tip does not rest on any ice. While stirring observe the displayed reading after about 15 seconds.

• Once the display is stable and no longer changes, write down the reading. You’ll need this if the Thermapen requires

adjustment.

4. Determine if an adjustment is necessary.

• If the reading from the ice bath test is within acceptable limits: 31.3°F and 32.7°F (–0.4°C and +0.4°C); then no

adjustment is necessary.

• If the reading is outside of acceptable limits proceed to making the trim adjustment.

Thermapen®Mk4

Trim Adjust Procedure

ThermoWorks, Inc • 741 E. Utah Valley Dr., American Fork, UT 84003 • ph: 801-756-7705 • fax: 801-756-8948 • techsuppor[email protected] • www.thermoworks.com

SET MENU

Making the Thermapen Trim Adjustment:

After determining that your Thermapen requires adjustment by following the

above procedure, follow these steps to trim the Thermapen:

1. Turn the Thermapen off by folding the probe away and

locking it into the probe retaining slot.

2. Calculate the trim adjustment value by subtracting the reading

written down in Step 3 of ‘Determining if Your Thermapen Requires

Adjustment’ from 32.0°F (or 0.0°C).

Example:

• Reading from my Thermapen = 32.9°F

• Adjustment Value: 32.0°F - 32.9°F = –0.9°F

3. Using a Philips screwdriver, remove the battery compartment to access the Set and Menu buttons.

4. Open the probe to turn on the Thermapen.

5. Hold down the menu button for 5 seconds until ‘SET TRIM’ is displayed. Press the Set button until the target trim

adjustment value is displayed. Note the trim adjustment value range is from –3.6°F to +3.6°F (-2°C to +2°C).

6. Press the Menu button to save the trim setting, ‘END’ is displayed for 1 second before returning to normal operation.

7. Retest in the ice bath to conﬁrm that the new reading is within the acceptable limits: between 31.3°F and 32.7°F (–0.4°C

and +0.4°C). If the reading is still outside of the acceptable limits, redo the trim adjustment by following steps 1 through 7.

For further technical assistance, contact Technical Support @ 801-756-7705 or techsupport@thermoworks.com.

ThermoWorks, Inc • 741 E. Utah Valley Dr., American Fork, UT 84003 • ph: 801-756-7705 • fax: 801-756-8948 • techsuppor[email protected] • www.thermoworks.com

P-15-007-M-2-a

Thermapen®Mk4

Trim Adjust Procedure

(continued)

SET MENU

Table des matières

Autres manuels ThermoWorks Thermomètre

ThermoWorks

ThermoWorks ProNeedle Manuel utilisateur

ThermoWorks

ThermoWorks Saf-T-Log Manuel utilisateur

ThermoWorks

ThermoWorks Therma K Manuel utilisateur

ThermoWorks

ThermoWorks TempTest 2 Manuel utilisateur

ThermoWorks

ThermoWorks Therma 20 Manuel utilisateur

ThermoWorks

ThermoWorks WAND Manuel utilisateur

ThermoWorks

ThermoWorks Super-Fast Thermapen Manuel utilisateur

ThermoWorks

ThermoWorks Signals Manuel utilisateur

ThermoWorks

ThermoWorks Smoke X4 Manuel d'instructions et de sécurité

ThermoWorks

ThermoWorks TW8060 Manuel utilisateur

ThermoWorks

ThermoWorks ChefAlarm TX-1100-OR Manuel utilisateur

ThermoWorks

ThermoWorks TW362B ThermoWorks Manuel utilisateur

ThermoWorks

ThermoWorks Smoke X4 Manuel utilisateur

ThermoWorks

ThermoWorks I.R.F.S. Manuel utilisateur

ThermoWorks

ThermoWorks Therma Differential Manuel utilisateur

ThermoWorks

ThermoWorks MicroTherma 2K Manuel utilisateur

ThermoWorks

ThermoWorks Thermapen Series Manuel utilisateur

ThermoWorks

ThermoWorks Therma 20 Plus Manuel utilisateur

ThermoWorks

ThermoWorks TempTest Blue Manuel utilisateur

ThermoWorks

ThermoWorks Signals Manuel utilisateur

ThermoWorks

ThermoWorks TW362B Manuel utilisateur

ThermoWorks

ThermoWorks Saf-T-Log Manuel utilisateur

ThermoWorks

ThermoWorks Smoke Manuel utilisateur

ThermoWorks

ThermoWorks TW362B Manuel utilisateur

Manuels Thermomètre populaires d'autres marques

Delton

Delton 981A Manuel utilisateur

Baker

Baker MM2P Manuel utilisateur

Tarmo

Tarmo 320281 Manuel utilisateur

Citizen

Citizen CTD 504 Manuel utilisateur

TFA

TFA 14.1500 Manuel utilisateur

Vive

Vive DMD1010 Manuel utilisateur

Gotemp

Gotemp THB4002 Manuel utilisateur

GREISINGER

GREISINGER G 1202 Manuel utilisateur

Amprobe

Amprobe TMD-53W Manuel utilisateur

Trotec

Trotec BP10 Manuel utilisateur

Radiance instruments

Radiance instruments RT616 Series Manuel utilisateur

Eurolec

Eurolec IR151 Manuel utilisateur

Scaneo

Scaneo TS42B Manuel utilisateur

Sper scientific

Sper scientific 800043 Manuel utilisateur

Microlife

Microlife NC 200 Mode d’emploi

Motorola

Motorola MBP69SN Guide de configuration

The MeatStick

The MeatStick The MeatStick Manuel utilisateur

Hama

Hama TH35-A Manuel utilisateur