Thermomax SA132 Manuel

AUTODIALLER /
QUICKDIALLER
- SA132
INSTRUCTION LEAFLET
ENGLISH
www.Thermomax-Group.com

CONTENTS
1SETUPATAGLANCE ................................................................................ 2
2FOREWORD …………………………………..........……………...……. 3
3INSTALLATION ……………………………………….......…………....… 4
4KEYPADANDINDICATORS ................................…………………….... 6
5SETTINGUPTHEUNIT ..............…………………………………….... 7
6TROUBLESHOOTINGGUIDE .............................................................. 12
1

1. SETUP AT A GLANCE
How to... Steps
Record
Emergency
Messages
Play Back
Emergency
Messages
Record
Telephone
Numbers
Send a
Test Call
Select Auto
Dialing Times
Select
Message
Playing
Duration
Reset the
System
(Speak into microphone
for 20 seconds max.)
5
!0
1
2
3
4
= 50 sec.
= 70 sec.
= 90 sec.
= 110 sec.
8
1 2
3
4
Duration
(Select only one key)
8
1 2
3
4
Sequence of telephone number
(Select only one key)
5
6
!
1
2
3
4
5
7
6
8
9
0
*
Telephone Number
1 2 3 4
5
6
1
Sequence of telephone number
(Select only one key)
1
2
3
4
5
7
6
8
9
Select one key
60
2

3
2. FOREWORD
The SA132 Autodialer / QuickDialer is an intelligent device designed to
connect to any security alarm control panel, and it is compatible with any of
the following Thermomax units - SM12, SM UNO, SM DUE, SM QUATTRO,
LCT-2, SMX 100, etc.). The Autodialer / QuickDialer enables the dialer to call
any phone numbers programmed to it when an emergency occurs. The
recorded messages played during the phone calls will alert either the
homeowner or a second party to take action.
The Autodialer / QuickDialer can memorize up to 6 telephone numbers of up
to 32 digits each, and you can record emergeny messages of up to 20
seconds on the system to be played during the phone calls.
The Autodialer / QuickDialer can be programmed to call telephone units,
mobile phones, pager and DISA (Direct Inward System Access) facilities.
Features:
•Built-in terminal block to connect to the alarm control panel for emergency
alert.
•All phone numbers, emergency messages, and settings are stored in Non-
Volatile Memory (NVM) permanently in case of power failure.
•Stores up to 6 telephone numbers (T1 - T6) with a maximum of 32 digits
each.
•20-second recording time for emergeny messages.
•In case of an emergency, press the
!
button on the Autodialer /
QuickDialer, which will immediately start dialing the phone numbers for
help.
•Detects dial tone, busy tone and ring back tone so as to perform auto dialing
or auto redialing when the line is busy. Each phone number will be dialed
for a maximum of 9 times.
•Alarm memory facility.

4
3. INSTALLATION
MOUNTINGTHEUNIT
To mount the unit on the wall, drill two holes for the 2 screws provided into
the wall, leaving a 5cm space between them, and hang the unit on the
screws as shown in Fig. 1.
Fig. 1
CONNECTINGTO TELEPHONELINE (PARALLELCONNECTION)
Insert the telephone line RJ11 jack to the Autodialer / QuickDialer’s phone
line socket. Connect the other end of the telephone line to the phone line
socket on the wall. See Fig. 2.
Fig. 2
CONNECTINGTOPOWER SOURCES
The Operating Voltage of the Autodialer / QuickDialer is 12V DC. Open the
cover as shown in Fig. 3, and connect the Autodialer / QuickDialer to the 12V
DC output of an alarm panel or 1 12V battery.
The QuickDialer is equipped with power input protection. When the +/-
battery polarity is connected wrongly, the red LED on the QuickDialer will not
illuminate.
Fig. 3
PRESS

CONNECTINGTO ATHERMOMAX UNIT
1. Connect the Autodialer / QuickDialer Connecting Wire, A7068, from the
terminals labelled BATTERY on the Battery Backup System to the Autodialer
/ QuickDialer input, (as illustrated in the diagram below).
2. Now connect the N.O. trigger input of the Autodialer / QuickDialer to the
alarm common (C) input of the Thermomax unit.
3. Connect the Autodialer / Quickdialer N.C. trigger input to the alarm N.C.
output of the Thermomax unit.
4. Connect the Battery Backup System to the mains and switch on.
Please refer to the set up instructions supplied with the Battery Backup
System.
Fig. 4
On initial power up, the red LED will be lit and the yellow LED will flash
indicating that the recorded message and telephone number have been
erased. The yellow LED will extinguish when set-up is complete.
5
THERMOMAX
C0329 - BATTERY BACKUP SYSTEM
+ TO + OF AUTODIALER
DCAC ++
BATTERY
- TO - OF AUTODIALER
RED WIRE TO + TERMINAL OF BATTERY
BLACK WIRE TO - TERMINAL OF BATTERY
PRESS

6
4. KEYPAD AND INDICATORS
KEYPAD
!
1 2
3
4 5
7
6
8
9
0
*
<PANIC> <SET> <PAUSE> <CLEAR>
LEDINDICATORS
LED
STATUS
OFF
ON
FLASH
GREEN
OFF-LINE
ON-LINE
DIALLING
YELLOW
STANDBY
REC / PLAY
INCOMPLETE SETTING OF
RECORDED MESSAGE
AND PHONE NUMBER
RED
POWER OFF
POWER ON
ALARM MEMORY
LEDINDICATION DURINGPROGRAMMING
•Each time any button is pressed, the Yellow LED will flash once to confirm
the input.
•When you press the once,the Yellow LED will flash once, on the
second press of this key, the Yellow LED will flash twice, and on the third
press of this key, the Yellow LED will be on for 1.5 second, indicating the
completion of a programming procedure.
•When pressing the key or if the next sequent key is not pressed over
an interval of 10 seconds or there is an incorrect input, the Yellow LED will
flash four times, indicating ans incorrect operation.
•When the red LED is flashing, the user cannot proceed with the
programming. To reset the Autodialer / QuickDialer press the key, (the
Red LED will illuminate continuously), you can then proceed with the
settings.

7
5. SETTING UP THE UNIT
EMERGENCYMESSAGES
1. Recording Message
The Autodialer / QuickDialer has a built-in microphone enabling you to
record the message phrases directly into the unit. As an example, the
following phrases can be recorded as the emergency message:
“This is Mr. Smith, at 10 The Strand, East Fincham. The house alarm has
been triggered, please send for help.”
To record the message, press the keys →→→and
start speaking directly into the microphone. As the message ends, press
the key to stop recording.
→→−−−−−−−−−−−−−−−−−−−−−
2. Playing Back Message
Once the phrases have been recorded by the Autodialer / QuickDialer, they
can be played back through the loudspeaker of a parallel connection
telephone unit so that you can check the recorded messages. To play the
recorded messages, do as follows:
→ → −−−−−−−−−−−−−−−−−−−−−
•While playing the message, the Yellow LED will illuminate simultaneously.
•To stop playing the message, simply press the key on the Autodialer /
QuickDialer.
NUMBERSTODIAL
Up to six telephone numbers can be memorized, with a maximum of 32
digits each.
1. Telephone Number
!
1
2
3
4
5
7
6
8
9
0
*
Telephone Number
1 2 3 4
5 6
1
Sequence of telephone number
(Select only one key)
MICROPHONE

8
•To revise the telephone numbers, repeat the previous procedure.
•To clear a recorded telephone number, do as follows:
→→
6
→ →
Sequence of telephone number
(select only one key)
•Due to the nature of some particular phone systems, busy tone or ring back
tone cannot easily be distinguished. To overcome this problem, press the
!
key after the telephone number for deferred playing (Autodialer /
QuickDialer will start playing messages 3.6 seconds after dialing the phone
number) :
→→
6
→
Sequence of telephone number
(select only one key)
→
7
6
→
!
→
Telephone Number Deferred
Playing
•For a telephone number without the “deferred playing”setting, the Autodialer
/ QuickDialer will try to determine the tone within 7 seconds after dialing the
number. If it is ring back tone, the Autodialer / QuickDialer will start playing
the messages; otherwise, it will hang up and dial the next number 5.5
seconds later or redial the same number 30 seconds later.
2. Pager Numbers
If the Autodialer / QuickDialer is dialing a pager, it may need to wait a while
before sending the paging message. This is achieved by entering one or
more after the pager number. (Each delays the system
operation for 3.6 seconds). In order to determine how many to enter
after the pager number, preliminary trial is absolutely required.
→→
6
→
Sequence of telephone number
(select only one key)
→
0
7
0
0
7
6
→
Pager Number
→ --------------- →
Waiting for transferring Prefix
→
7
6
→ →
Display Number Prefix

9
3. Programming an internal PABX telephone exchange through Direct Inward
System Access (DISA) facility
→→
6
→
Sequence of telephone number
(Select only one key)
→
7
−−− → --------------------
Telephone Number Waiting for transfer
→→
!
→
Extension Deferred
Number Playing
4. Connected to PABX system or ISDN switcher
If the Autodialer / QuickDialer is connected to an internal PABX telephone
exchange or ISDN switcher, a prefix digit (e.g. 9) is normally required before
an outside line can be obtained.
If the prefix dialing function is activated, the Autodialer / QuickDialer will dial
the first digit (prefix) entered for every telephone number, and then start dial
tone detecting function. To activate this function, enter
0
. To disable the
function, enter . The setting is done as follows:
→
9
→ →
0
→
Prefix (select only one key)
Before entering the telephone number (“27654321” for the example below),
press “9” for the dial output prefix.
→→
6
→
Sequence of telephone number
(select only one key)
→
9
→
7
6
→
Prefix Telephone Number
SENDINGATESTCALL
It is possible to send one test call by selecting one of the telephone
numbers to call.
→→
6
→
Sequence of telephone number
(select only one key)
The telephone number of the test call will be dialed only once whether the
line is busy or not.
Table des matières
Autres manuels Thermomax Unité de contrôle
Manuels Unité de contrôle populaires d'autres marques

Festo
Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation
JS Automation MPC3034A Manuel utilisateur

JAUDT
JAUDT SW GII 6406 Series Guide rapide

Spektrum
Spektrum Air Module System Manuel utilisateur

BOC Edwards
BOC Edwards Q Series Manuel utilisateur












