Thermo Scientific Orion Versa Star Manuel utilisateur

Thermo Scientiﬁc Orion VERSA STAR™

Conductivity/Temperature Module

Reference Guide

Ross and the COIL trade dress are trademarks of Thermo Fisher Scientiﬁc, Inc. and

its subsidiaries.

AQUAfast, AQUASensors, BOD AutoEZ, ionplus, KNIpHE, LogR, No Cal, ORION, perpHect,

PerpHecT, pHISA, pHuture, Pure Water, Sage, ROSS, ROSS Ultra, Sure-Flow, Titrator PLUS, and

TURBO2 are registered trademarks of Thermo Fisher Scientiﬁc, Inc. and its subsidiaries.

A+, All in One, Aplus, AUTO-BAR, AUTO-CAL, Auto-ID, AUTO-READ, AUTO-STIR,

Auto-Test, AutoTration, CISA, digital LogR, DuraProbe, EZ Startup, ISEasy,

Low Maintenance Triode, Minimum Stir Requirement, MSR, NISS, Optimum Results, Orion Dual

Star, Orion Star, SAOB, SMART AVERAGING, SMART STABILITY, Star LogR, Star Navigator 21,

Stat Face, Triode are trademarks of Thermo Fisher Scientiﬁc, Inc. and its subsidiaries.

Guaranteed Success and The Technical Edge are service marks of Thermo Fisher Scientiﬁc, Inc.

and its subsidiaries.

Thermo Fisher Scientiﬁc, Inc. and its subsidiaries.

The speciﬁcations, descriptions, drawings, ordering information and part numbers within this

document are subject to change without notice.

This publication supersedes all previous publications on this subject.

Thermo Scientific Orion VERSA STAR™ Conductivity/Temperature Module

Table of Contents

Chapter 1 Introduction ..........................................................1

Chapter 2 Module Overview .....................................................3

Module Connections and Inputs ........................................ 3

Module Maintenance.................................................. 4

Display Information From Module ....................................... 4

Chapter 3 Setup Menus .........................................................5

Setup Menus for Primary Measurements ................................ 5

Read Type Information..............................6

Temperature Compensation Options ...................6

Setup Menu for Temperature ........................................... 7

Chapter 4 Conductivity Calibration ...............................................9

Chapter 5 Temperature Calibration ..............................................11

Chapter 6 Measurement........................................................13

Chapter 7 Methods ............................................................15

Chapter 8 Data Storage and Review .............................................17

Data Storage Settings ................................................ 17

Measurement Read Type...........................17

Datalog, Computer and Printer Export Settings ..........17

Datalog Review ...................................................... 17

Calibration Review................................................... 18

Chapter 9 Customer Services ...................................................19

Troubleshooting Guide................................................ 19

Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Warranty and Registration ............................................ 19

WEEE Compliance ................................................... 19

Declaration of Conformity ............................................. 20

Conductivity/Temperature Module Specifications ....................... 21

Ordering Information ................................................. 22

Appendix Advanced Features...................................................27

Conductivity Temperature Compensation and Reference Temperature ..... 27

Conductivity and Total Dissolved Solids (TDS)........................... 27

Conductivity Automatic Calibration .................................... 27

Table of Conductivity Standards Values Vs. Temperature ................. 28

This page intentionally left blank.

Thermo Scientiﬁc Orion VERSA STAR Conductivity/Temperature Module

Chapter 1 Introduction

Thank you for your purchase of the Thermo Scientiﬁc Orion VERSA STAR™ Conductivity/Temperature Module.

This module is for use with the Thermo Scientiﬁc Orion VERSA STAR Advanced Electrochemistry Benchtop Meter.

Some key features of this module include:

• Conductivity,TDS,salinityandresistivitycapabilities

• Selectablereadingreferencetemperaturesof5,10,15,20or25°C

• Compatibilitywith2-or4-cellconductivitycells

• Linear,non-linear,nLFuorEPcurveoptionsforconductivity

• Choiceofpracticalsalinityornaturalseawatercurvesforsalinityreadings

• Automaticandmanualdataloggingoptions

Pleasereadthisreferenceguidethoroughly.Anyuseoutsideoftheseinstructionsmayinvalidateyourwarrantyand

causepermanentdamagetothemeter.

This page intentionally left blank.

Thermo Scientiﬁc Orion VERSA STAR Conductivity/Temperature Module

Chapter 2 Module Overview

Toconnectthemodulestothemeterandforspecicinformationregardingthemeteroutputs,pleaseseethe

OrionVERSASTARReferenceGuide.TheReferenceGuideisontheCDincludedwiththemeterandalsoavailable

at www.thermoscientiﬁc.com/water.

Module Connections and Inputs

1. Selectaconductivitycellbasedonsamplerangeandreportingrequirements.

2. Placeconductivitycellinthemeter’selectrodearm.

3. Attachthe8pinmini-DINconnectionintotheconductivitymodule.

4. AttachtheOrionStarstirrerprobe(cat.no.096019,soldseparately)tothesideofthemeterandinto

themeter'selectrodearm,ifneededforyourtestmethod.

5. Setupareawithstandards,rinsewater,sample&othersupplies.

6. Connectthemeterfordatacollection(Hyperterminal,LIMS,StarPrinter,etc),ifdesired.

7. PowertheOrionVERSASTARmeter,stirrer,anddatacollectiondevice(s).

Conductivity Module

8pinmini-DINconnectorfor

conductivityprobe

4Thermo Scientiﬁc Orion VERSA STAR Conductivity/Temperature Module

Module Maintenance

Forroutinemaintenance,dustandwipethemodulewithadampcloth.Ifnecessary,warmwaterormildwater-based

detergentcanbeused.Maintenancecanbeperformedonadaily,weeklyormonthlybasis,asrequiredbyoperating

environment.Immediatelyremoveanyspilledsubstanceusingthepropercleaningprocedureforthatspilltype.

Display Information from Module

ExampleConductivityMeasurementScreen–SingleChannel

Dateandtime

Sample

temperature

Primaryreading

Informationon

lastcalibration

Theinformationonthedisplaycanbecustomized.

Enterthesetupmenutomakechanges.

1.PressSetup.

2.UsethearrowkeystohighlightInst.Settings,

press (f3/select) key.

3.UsethearrowkeytohighlightDisplayView.

 Press(f3/select) key.

4.Followtheonscreenpromptstochoosewhatyou

would like to see on the measurement screen.

Thermo Scientiﬁc Orion VERSA STAR Conductivity/Temperature Module

Chapter 3 Setup Menus

Setup Menus for Primary Measurements

1. SelecttheConductivitychannelbypressingthechannelkey,thenpressf3 (Setup).

2. Arrowovertohighlighttheappropriateconductivitymoduleforsetup,pressf3 (Select).

3. ArrowthecursortoMode,pressf3 (Select),arrowtoConductivity,pressf3 (Select).

4. Selecttheoptionsforyourtesting.

TDS, Salinity and Resistivity Setup Menus

Conductivity Setup Menu

(Default values are in bold in the table below)

ProbeSerialNumber Input

SampleID Off,Manual,AutoIncrement

Stability Smart,Fast,Medium,Slow

Averaging Off,Automatic Smart

Read Type AutoRead,Timed,Continuous

CellK(Constant) Inputcellconstant

Reference Temperature 5,10,15,20,or25 ºC

Temp Compensation Linear,nLFn,nLFu,EP

Temperature Coefﬁcient 2.1

Alarm** Limit,CalDue,SetPoint

**Limitandsetpointalarmdefaultsetto‘off’.

Calduealarmsetto12hours.

TDS Setup Menu (Default values in bold)

Read Type AutoRead,Timed,Continuous

CellK(Constant) Inputcellconstant

TDSFactor 0.50

Reference Temperature 5,10,15,20,or25 ºC

Temp Compensation Linear,nLFn,nLFu,EP,Off

ProbeSerialNumber Input

Stability Smart,Fast,Medium,Slow

Averaging Off,Automatic Smart

Alarm Limit,SetPoint

Cell Type Standard,USP

Resistivity Setup Menu (Default values in bold)

Read Type AutoRead,Timed,Continuous

CellK(Constant) Inputcellconstant

Reference Temperature 5,10,15,20,or25ºC

Temp Compensation Linear,nLFn,nLFu,EP,Off

Stability Smart,Fast,Medium,Slow

Averaging Off,Automatic Smart

Alarm Limit,SetPoint

Cell Type Standard,USP

Salinity Setup Menu (Default values in bold)

Read Type AutoRead,Timed,Continuous

CellK(Constant) Inputcellconstant

Salinity Type Practical Salinity,SeaWater

Stability Smart,Fast,Medium,Slow

Averaging Off,Automatic Smart

Alarm Limit,SetPoint

Cell Type Standard,USP

6Thermo Scientiﬁc Orion VERSA STAR Conductivity/Temperature Module

Read Type Information

Therearethreemainreadtypesavailableasshowninthesetupmenus.

• Auto-Read – Themeterwilldisplaythemeasurementasitstabilizesandlockandholdthe

measurementwhenitisstable.(TheARiconwilllockonthescreen.)Oncethemeasurementislocked,

themeterwillautomaticallyexportthemeasurementtothedatalog,ifthedatalogisenabledin

thesetupmenu,andtoaprinterorcomputer,ifaprinterorcomputerisconnectedtothemeterand

enabledinthesetupmenu.Totakeanewmeasurement,pressmeasure (esc)/1.

• Timed – Themeterwillreadanddisplayameasurementatthesettimeintervalthatisprogrammed

bytheoperator.Therearetwooptions:

 1. Bychecking/selectingthe"Interval"box,atthesettimeinterval,themeterwillautomatically

 exportthemeasurementtothedatalog,ifthedatalogisenabledinthesetupmenu,andtoa

 printerorcomputer,ifaprinterorcomputerisconnectedtothemeterandenabledinthesetup

 menu.Ifselected,enterthetimeintervalvalueinahours:minutes:secondsformatusingthe

numeric keypad and press f3 (select) key.

 2. Ifthe"Interval"boxisunchecked/notselected,asingletimedmeasurementwillbetaken.

 Themeterwillapplythesamesavingandexportingdataconditionsaswiththesettime

 intervaltorecordandexportdata,butlockafteronetimedintervalhasexpired.Press

measure (esc)/1toresetthecountdownclockandtakeanewreading.

• Continuous – The meter will continuously measure and update the display. This read type is useful

whenperforminganexperimentthatrequirescontinuousmeasurementstobetaken.Pressthe

log/print/0keytoexportthemeasurementtothedatalog,ifthedatalogisenabledinthesetup

menu,andtoaprinterorcomputer,ifaprinterorcomputerisconnectedtothemeterandenabledin

the setup.

Temperature Compensation Options

Theseoptionscanvaryaccordingtothemeasurementmode.

• Linear –Mostbenecialforusewithsampleswithknownandlineartemperaturecoefcients.

• nLFn –Thisabbreviationisfornon-linearnaturalpurewater.Itworksbestforlowconductivitywater

suchaspurewatersandnaturalwaters(ground,wellorsurfacewaters).

• nLFu –Thisabbreviationisfornon-linearultrapurewaterthatcontainsnoairorcarbondioxide.

• EP –Temperature-compensationisturnedoffwhenthisisselected.Usingthisfeatureresultsin

warninglimitsbeingdisplayedwhenthepurewatersampleisovertheacceptablereadingforthat

temperatureperEPorUSPrequirements.

Autres manuels pour Orion Versa Star

Table des matières

Autres manuels Thermo Scientific Unité de contrôle

Thermo Scientific

Thermo Scientific Nicolet FT-IR Manuel utilisateur

Thermo Scientific

Thermo Scientific Nicolet iS50 GC-IR Manuel utilisateur

Thermo Scientific

Thermo Scientific VSTAR-ISE Manuel utilisateur

Thermo Scientific

Thermo Scientific Smart-Vue Manuel utilisateur

Thermo Scientific

Thermo Scientific Smart-Vue Manuel utilisateur

Thermo Scientific

Thermo Scientific Orion VERSA STAR VSTAR-RD Manuel utilisateur

Thermo Scientific

Thermo Scientific Orion Versa Star Manuel utilisateur

Thermo Scientific

Thermo Scientific ETD Manuel utilisateur

Thermo Scientific

Thermo Scientific Smart-Vue Manuel de service

Manuels Unité de contrôle populaires d'autres marques

Festo

Festo Compact Performance CP-FB6-E Manuel de la liste des pièces

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuel utilisateur

JS Automation

JS Automation MPC3034A Manuel utilisateur

JAUDT

JAUDT SW GII 6406 Series Guide rapide

Spektrum

Spektrum Air Module System Manuel utilisateur

BOC Edwards

BOC Edwards Q Series Manuel utilisateur

KHADAS

KHADAS BT Magic Manuel utilisateur

Etherma

Etherma eNEXHO-IL Manuel utilisateur

PMFoundations

PMFoundations Attenuverter Manuel utilisateur

GEA

GEA VARIVENT Manuel utilisateur

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuel utilisateur

Altronix

Altronix LINQ8PD Instructions de montage

Eaton

Eaton Powerware Series Manuel utilisateur

WAGO

WAGO 750-407/040-000 Manuel utilisateur

Sony

Sony CCU-590 Manuel utilisateur

Graco

Graco 25D614 Manuel utilisateur

Task Force Tips

Task Force Tips YE-RF-900 Manuel de programmation

Shini

Shini SPV-U Series Manuel utilisateur