Theben ThePiccola P360-100 DE Manuel utilisateur

thePiccola P360-100 DE WH

2090200

307146 02

Presence detector

1. Basic safety information 3

2. Proper use 3

Disposal 3

3. Device description 4

4. Installation and connection4

Installing the presence

detector 4

Connecting the presence

detector 6

Individual switching 7

Parallel switching 7

Push button control 8

Installation instructions and

detection area 8

5. Walking test 9

6. Setting 9

Setting the brightness

switching value (LUX) 10

Setting the time delay (TIME) 12

7. Settings with remote

control 12

Settings by using theSenda S 13

Settings by using theSenda P 13

Settings with Sendo Pro

868-A 15

8. Technical data 15

9. Contact 16

1. Basic safety information

Danger of death through electric shock or fire!

 Installation should only be carried out by a

qualied electrician!

WARNING

•The device conforms with EN 60669-2-1 if correctly

installed

2. Proper use

•Presence detector for automatic lighting control depen-

dent on presence and brightness

•Suitable for ceiling installation (false ceilings)

•Suitable for small rooms, corridors, toilets, etc.

Disposal

Dispose of the device in an environmentally sound manner

(electronic waste)

3. Device description

Sensor unit

red LED

Power supply unit

2 potentiometers for setting

the time delay (TIME) and

the brightness switching

value (LUX)

4. Installation and connection

Installing the presence detector

LInstallation height: 2–4 m

LCable length: 45 cm

LPresence detector requires clear line of sight to people

Disconnect power source

Create a ceiling opening of Ø 34–36 mm

Connect power supply unit according to the

wiring diagram

Make settings at the potentiometers

Push the power supply unit through the ceiling opening

and attach the sensor with tensioned springs in the ceiling

Ø 34-36 mm

6–8 mm

max. 1 x 2,5 mm2

Connecting the presence detector

Danger of death through electric shock or fire!

 Installation should only be carried out by a

qualied electrician!

WARNING

Disconnect power source

Ensure device cannot be switched on

Check absence of voltage

Earth and bypass

Cover or shield any adjacent live components

The warm-up phase takes approx. 1 min. The LED is perma-

nently red.

Individual switching

In individual switching, the presence detector as master

detects presence and brightness and controls lighting.

L’

Parallel switching

If the detection area covered by a single presence detector

is insufcient (in larger rooms), then the switch contacts of

several detectors can be directly connected with each other.

Set brightness switching value and time delay on all detec-

tors identically.

L’ L’

Push button control

The lighting can be manually switched on/off via a button. If

the light is switched on manually, it will remain on as long as

people are present (plus time delay). Then the light goes into

the set automatic mode. If the light is switched off manually,

it will remain off as long as people are present (plus time

delay). Then the light goes back to automatic mode.

Installation instructions and detection

area

As the detector reacts to variations in temperature, avoid the

following situations:

Do not point the presence detector at objects with highly-

reective surfaces such as mirrors, etc.

Do not install the presence detector near heat sources such

as heating vents, air conditioners, lamps, etc.

Do not point the presence detector at objects that move in

the wind such as curtains, large plants, etc.

Pay attention to the direction of motion during the test run.

2,5 m

360°

Ø 2 m

Ø 8 m

Lrecommended installation height: 2 – 4 m

LTransverse detection area: 8 m (transversal to the detector)

LFrontal detection area: 2 m (directly approaching the detector)

LDetection angle: 360°

5. Walking test

The walking test is used to test the detection area.

Set the time delay potentiometer (TIME) to T(Test). The

presence detector only reacts to movements, brightness

measurement is switched off.

Walk through the detection area. Every detected movement

is indicated by the LED, and the light switch contact closes.

When no one is present the light switch contact opens after

3 seconds.

3 sec

6. Setting

The presence detector has 2 potentiometers for setting time

delay (TIME) and brightness switching value (LUX).

Setting the brightness switching value

(LUX)

You can set different brightness values with the potentiome-

ter for the brightness switching value (LUX).

If you want to change the preset brightness

Set the potentiometer to the desired brightness (5 – 1000

lux = ).

Autres manuels pour thePiccola P360-100 DE

Table des matières

Autres manuels Theben Capteur de sécurité

Theben

Theben thePiccola P360-100 DE Manuel utilisateur

Theben

Theben compact office 24V Manuel utilisateur

Theben

Theben theMova S360-101 DE WH Manuel utilisateur

Theben

Theben thePassa P360-101 UP WH Manuel utilisateur

Theben

Theben thePrema S360-100 E UP WH Manuel utilisateur

Theben

Theben compact office EIB Manuel utilisateur

Theben

Theben theRonda P360-100 M UP WH Manuel utilisateur

Theben

Theben ECO-IR 180EIB-AC Manuel utilisateur

Theben

Theben ECO-IR DUAL-C NT Manuel utilisateur

Theben

Theben LUXA 103-100 AP WH Manuel utilisateur

Theben

Theben TIMEGUARD LEDPROPCB Manuel

Theben

Theben PlanoCentro 101-E Series Manuel utilisateur

Theben

Theben theLeda D B AL Manuel utilisateur

Theben

Theben PlanoCentro A-KNX Instructions d'utilisation

Theben

Theben thePixa P360 24V KNX UP WH Manuel utilisateur

Theben

Theben SPHINX 331 S KNX Manuel utilisateur

Theben

Theben LUXA 103-100 DE WH Manuel utilisateur

Theben

Theben thePassa P360-221 DALI UP WH Manuel utilisateur

Theben

Theben Timeguard PDSM361AB Manuel

Theben

Theben LUXA 104 S360-200-24 DE-UP WH Manuel utilisateur

Theben

Theben theLeda D S AL Manuel utilisateur

Theben

Theben PlanoCentro 000-E Series Manuel utilisateur

Theben

Theben theRonda P360-330 DALI UP WH Manuel utilisateur

Theben

Theben theMura S180-100 UP WH Manuel utilisateur

Manuels Capteur de sécurité populaires d'autres marques

THORLABS

THORLABS PDA10JT Manuel utilisateur

Waeco

Waeco UV-DETECT Manuel utilisateur

Intermatic

Intermatic IOS-DSIMF Manuel utilisateur

urmet domus

urmet domus 1083 Manuel utilisateur

Siemens

Siemens AZL66 Series Manuel utilisateur

BTI

BTI Profiline Multi Finder Manuel utilisateur

Challenger

Challenger SL01 Manuel utilisateur

DMP Electronics

DMP Electronics 1122INT Manuel utilisateur

Rielta

Rielta Ladoga MK-RK Manuel utilisateur

Mirion Technologies

Mirion Technologies ACCURAD PRD Manuel utilisateur

Bosch

Bosch DS835 Manuel utilisateur

DBI SALA

DBI SALA EZ Stop Manuel de l'opérateur

Lamptime

Lamptime ST05C Manuel utilisateur

Ubiquiti

Ubiquiti MFI-MSC Manuel utilisateur

Subsite

Subsite 910R Instructions d'installation

Satel

Satel OPAL Pro Manuel utilisateur

Aleph

Aleph XC-1XTEU Manuel utilisateur

Pima

Pima LARIS QUAD Manuel utilisateur